u-boot/include/linux/usb/xhci-fsl.h
Sriram Dash e915716a5c drivers: usb: xhci-fsl: Change burst beat and outstanding pipelined transfers requests
This is required for better performance, and performs below tuning:
1. Enable burst length set, and define it as 4/8/16.
2. Set burst request limit to 16 requests.

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
2016-09-27 23:30:16 +02:00

74 lines
2.6 KiB
C

/*
* Copyright 2015 Freescale Semiconductor, Inc.
*
* FSL USB HOST xHCI Controller
*
* Author: Ramneek Mehresh<ramneek.mehresh@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _ASM_ARCH_XHCI_FSL_H_
#define _ASM_ARCH_XHCI_FSL_H_
/* Default to the FSL XHCI defines */
#define USB3_PWRCTL_CLK_CMD_MASK 0x3FE000
#define USB3_PWRCTL_CLK_FREQ_MASK 0xFFC
#define USB3_PHY_PARTIAL_RX_POWERON BIT(6)
#define USB3_PHY_RX_POWERON BIT(14)
#define USB3_PHY_TX_POWERON BIT(15)
#define USB3_PHY_TX_RX_POWERON (USB3_PHY_RX_POWERON | USB3_PHY_TX_POWERON)
#define USB3_PWRCTL_CLK_CMD_SHIFT 14
#define USB3_PWRCTL_CLK_FREQ_SHIFT 22
#define USB3_ENABLE_BEAT_BURST 0xF
#define USB3_ENABLE_BEAT_BURST_MASK 0xFF
#define USB3_SET_BEAT_BURST_LIMIT 0xF00
/* USBOTGSS_WRAPPER definitions */
#define USBOTGSS_WRAPRESET BIT(17)
#define USBOTGSS_DMADISABLE BIT(16)
#define USBOTGSS_STANDBYMODE_NO_STANDBY BIT(4)
#define USBOTGSS_STANDBYMODE_SMRT BIT(5)
#define USBOTGSS_STANDBYMODE_SMRT_WKUP (0x3 << 4)
#define USBOTGSS_IDLEMODE_NOIDLE BIT(2)
#define USBOTGSS_IDLEMODE_SMRT BIT(3)
#define USBOTGSS_IDLEMODE_SMRT_WKUP (0x3 << 2)
/* USBOTGSS_IRQENABLE_SET_0 bit */
#define USBOTGSS_COREIRQ_EN BIT(1)
/* USBOTGSS_IRQENABLE_SET_1 bits */
#define USBOTGSS_IRQ_SET_1_IDPULLUP_FALL_EN BIT(1)
#define USBOTGSS_IRQ_SET_1_DISCHRGVBUS_FALL_EN BIT(3)
#define USBOTGSS_IRQ_SET_1_CHRGVBUS_FALL_EN BIT(4)
#define USBOTGSS_IRQ_SET_1_DRVVBUS_FALL_EN BIT(5)
#define USBOTGSS_IRQ_SET_1_IDPULLUP_RISE_EN BIT(8)
#define USBOTGSS_IRQ_SET_1_DISCHRGVBUS_RISE_EN BIT(11)
#define USBOTGSS_IRQ_SET_1_CHRGVBUS_RISE_EN BIT(12)
#define USBOTGSS_IRQ_SET_1_DRVVBUS_RISE_EN BIT(13)
#define USBOTGSS_IRQ_SET_1_OEVT_EN BIT(16)
#define USBOTGSS_IRQ_SET_1_DMADISABLECLR_EN BIT(17)
struct fsl_xhci {
struct xhci_hccr *hcd;
struct dwc3 *dwc3_reg;
};
#if defined(CONFIG_LS102XA) || defined(CONFIG_ARCH_LS1012A)
#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_XHCI_USB1_ADDR
#define CONFIG_SYS_FSL_XHCI_USB2_ADDR 0
#define CONFIG_SYS_FSL_XHCI_USB3_ADDR 0
#elif defined(CONFIG_LS2080A)
#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_XHCI_USB1_ADDR
#define CONFIG_SYS_FSL_XHCI_USB2_ADDR CONFIG_SYS_XHCI_USB2_ADDR
#define CONFIG_SYS_FSL_XHCI_USB3_ADDR 0
#elif defined(CONFIG_LS1043A)
#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_XHCI_USB1_ADDR
#define CONFIG_SYS_FSL_XHCI_USB2_ADDR CONFIG_SYS_XHCI_USB2_ADDR
#define CONFIG_SYS_FSL_XHCI_USB3_ADDR CONFIG_SYS_XHCI_USB3_ADDR
#endif
#define FSL_USB_XHCI_ADDR {CONFIG_SYS_FSL_XHCI_USB1_ADDR, \
CONFIG_SYS_FSL_XHCI_USB2_ADDR, \
CONFIG_SYS_FSL_XHCI_USB3_ADDR}
#endif /* _ASM_ARCH_XHCI_FSL_H_ */