u-boot/include/configs/stv0991.h
Vignesh R 57897c13de spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.

So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.

[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-04 16:38:12 +01:00

81 lines
2.1 KiB
C

/*
* (C) Copyright 2014
* Vikas Manocha, STMicroelectronics, <vikas.manocha@st.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_STV0991_H
#define __CONFIG_STV0991_H
#define CONFIG_SYS_DCACHE_OFF
#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_SYS_CORTEX_R4
#define CONFIG_SYS_NO_FLASH
/* ram memory-related information */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define PHYS_SDRAM_1_SIZE 0x00198000
#define CONFIG_ENV_SIZE 0x10000
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
#define CONFIG_ENV_OFFSET 0x30000
#define CONFIG_ENV_ADDR \
(PHYS_SDRAM_1_SIZE - CONFIG_ENV_SIZE)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024)
/* serial port (PL011) configuration */
#define CONFIG_BAUDRATE 115200
#define CONFIG_PL01X_SERIAL
/* user interface */
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+sizeof(CONFIG_SYS_PROMPT) + 16)
/* MISC */
#define CONFIG_SYS_LOAD_ADDR 0x00000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x8000
#define CONFIG_SYS_INIT_RAM_ADDR 0x00190000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* U-Boot Load Address */
#define CONFIG_SYS_TEXT_BASE 0x00010000
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* GMAC related configs */
#define CONFIG_MII
#define CONFIG_DW_ALTDESCRIPTOR
#define CONFIG_PHY_MICREL
/* Command support defines */
#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
#define CONFIG_SYS_MEMTEST_START 0x0000
#define CONFIG_SYS_MEMTEST_END 1024*1024
/* Misc configuration */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_BOOTCOMMAND "go 0x40040000"
/*
+ * QSPI support
+ */
#ifdef CONFIG_OF_CONTROL /* QSPI is controlled via DT */
#define CONFIG_CQSPI_DECODER 0
#define CONFIG_CQSPI_REF_CLK ((30/4)/2)*1000*1000
#define CONFIG_BOUNCE_BUFFER
#endif
#endif /* __CONFIG_H */