mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 10:48:51 +00:00
10f6e4dc3a
This converts the following to Kconfig: CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_SPL_MALLOC_START We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to control if we have a malloc pool or not. Signed-off-by: Tom Rini <trini@konsulko.com>
111 lines
2.8 KiB
Text
111 lines
2.8 KiB
Text
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_SPL_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_COUNTER_FREQUENCY=12500000
|
|
CONFIG_TARGET_LS1021ATWR=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x1020000
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x20000
|
|
CONFIG_ENV_OFFSET=0x300000
|
|
CONFIG_SYS_I2C_MXC_I2C1=y
|
|
CONFIG_SYS_I2C_MXC_I2C2=y
|
|
CONFIG_SYS_I2C_MXC_I2C3=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-twr-duart"
|
|
CONFIG_SPL_TEXT_BASE=0x10000000
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL=y
|
|
CONFIG_SYS_LOAD_ADDR=0x82000000
|
|
CONFIG_AHCI=y
|
|
CONFIG_SYS_MEMTEST_START=0x80000000
|
|
CONFIG_SYS_MEMTEST_END=0x9fffffff
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_FIT=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_RAMBOOT_PBL=y
|
|
CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1021atwr/ls102xa_pbi.cfg"
|
|
CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg"
|
|
CONFIG_SD_BOOT=y
|
|
CONFIG_SD_BOOT_QSPI=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0"
|
|
CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt"
|
|
CONFIG_SILENT_CONSOLE=y
|
|
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
|
CONFIG_ARCH_MISC_INIT=y
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_ID_EEPROM=y
|
|
CONFIG_SPL_MAX_SIZE=0x1a000
|
|
CONFIG_SPL_PAD_TO=0x1c000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0x80100000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x80000
|
|
CONFIG_SPL_FSL_PBL=y
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x1001d000
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
|
|
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x82100000
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xe8
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_MPC8XXX_INIT_DDR=y
|
|
CONFIG_SPL_WATCHDOG=y
|
|
CONFIG_SYS_CBSIZE=256
|
|
CONFIG_SYS_PBSIZE=276
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_MEMINFO=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="ethernet@2d10000"
|
|
CONFIG_DM=y
|
|
CONFIG_SATA=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
CONFIG_MPC8XXX_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SPL_SYS_I2C_LEGACY=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x53
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHY_ATHEROS=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_DM_MDIO=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_TSEC_ENET=y
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PCI=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_DSPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|