mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
190 lines
4 KiB
C
190 lines
4 KiB
C
/*
|
|
* Copyright (C) 2010 Freescale Semiconductor, Inc.
|
|
* Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <hwconfig.h>
|
|
#include <i2c.h>
|
|
#include <spi.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <pci.h>
|
|
#include <mpc83xx.h>
|
|
#include <vsc7385.h>
|
|
#include <netdev.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <asm/io.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <asm/fsl_mpc83xx_serdes.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* The following are used to control the SPI chip selects for the SPI command.
|
|
*/
|
|
#ifdef CONFIG_MPC8XXX_SPI
|
|
|
|
#define SPI_CS_MASK 0x00400000
|
|
|
|
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
|
|
{
|
|
return bus == 0 && cs == 0;
|
|
}
|
|
|
|
void spi_cs_activate(struct spi_slave *slave)
|
|
{
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
|
|
/* active low */
|
|
clrbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
|
|
}
|
|
|
|
void spi_cs_deactivate(struct spi_slave *slave)
|
|
{
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
|
|
/* inactive high */
|
|
setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
|
|
}
|
|
#endif /* CONFIG_MPC8XXX_SPI */
|
|
|
|
#ifdef CONFIG_FSL_ESDHC
|
|
int board_mmc_init(bd_t *bd)
|
|
{
|
|
return fsl_esdhc_mmc_init(bd);
|
|
}
|
|
#endif
|
|
|
|
static u8 read_board_info(void)
|
|
{
|
|
u8 val8;
|
|
i2c_set_bus_num(0);
|
|
|
|
if (i2c_read(CONFIG_SYS_I2C_PCF8574A_ADDR, 0, 0, &val8, 1) == 0)
|
|
return val8;
|
|
else
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
static const char * const rev_str[] = {
|
|
"1.0",
|
|
"<reserved>",
|
|
"<reserved>",
|
|
"<reserved>",
|
|
"<unknown>",
|
|
};
|
|
u8 info;
|
|
int i;
|
|
|
|
info = read_board_info();
|
|
i = (!info) ? 4 : info & 0x03;
|
|
|
|
printf("Board: Freescale MPC8308RDB Rev %s\n", rev_str[i]);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct pci_region pcie_regions_0[] = {
|
|
{
|
|
.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
|
|
.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
|
|
.size = CONFIG_SYS_PCIE1_MEM_SIZE,
|
|
.flags = PCI_REGION_MEM,
|
|
},
|
|
{
|
|
.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
|
|
.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
|
|
.size = CONFIG_SYS_PCIE1_IO_SIZE,
|
|
.flags = PCI_REGION_IO,
|
|
},
|
|
};
|
|
|
|
void pci_init_board(void)
|
|
{
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
sysconf83xx_t *sysconf = &immr->sysconf;
|
|
law83xx_t *pcie_law = sysconf->pcielaw;
|
|
struct pci_region *pcie_reg[] = { pcie_regions_0 };
|
|
|
|
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
|
|
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
|
|
|
|
/* Deassert the resets in the control register */
|
|
out_be32(&sysconf->pecr1, 0xE0008000);
|
|
udelay(2000);
|
|
|
|
/* Configure PCI Express Local Access Windows */
|
|
out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
|
|
out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
|
|
|
|
mpc83xx_pcie_init(1, pcie_reg);
|
|
}
|
|
/*
|
|
* Miscellaneous late-boot configurations
|
|
*
|
|
* If a VSC7385 microcode image is present, then upload it.
|
|
*/
|
|
int misc_init_r(void)
|
|
{
|
|
#ifdef CONFIG_MPC8XXX_SPI
|
|
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
|
|
sysconf83xx_t *sysconf = &immr->sysconf;
|
|
|
|
/*
|
|
* Set proper bits in SICRH to allow SPI on header J8
|
|
*
|
|
* NOTE: this breaks the TSEC2 interface, attached to the Vitesse
|
|
* switch. The pinmux configuration does not have a fine enough
|
|
* granularity to support both simultaneously.
|
|
*/
|
|
clrsetbits_be32(&sysconf->sicrh, SICRH_GPIO_A_TSEC2, SICRH_GPIO_A_GPIO);
|
|
puts("WARNING: SPI enabled, TSEC2 support is broken\n");
|
|
|
|
/* Set header J8 SPI chip select output, disabled */
|
|
setbits_be32(&immr->gpio[0].dir, SPI_CS_MASK);
|
|
setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
|
|
#endif
|
|
|
|
#ifdef CONFIG_VSC7385_IMAGE
|
|
if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
|
|
CONFIG_VSC7385_IMAGE_SIZE)) {
|
|
puts("Failure uploading VSC7385 microcode.\n");
|
|
return 1;
|
|
}
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
#if defined(CONFIG_OF_BOARD_SETUP)
|
|
void ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
ft_cpu_setup(blob, bd);
|
|
fdt_fixup_dr_usb(blob, bd);
|
|
fdt_fixup_esdhc(blob, bd);
|
|
}
|
|
#endif
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int rv, num_if = 0;
|
|
|
|
/* Initialize TSECs first */
|
|
rv = cpu_eth_init(bis);
|
|
if (rv >= 0)
|
|
num_if += rv;
|
|
else
|
|
printf("ERROR: failed to initialize TSECs.\n");
|
|
|
|
rv = pci_eth_init(bis);
|
|
if (rv >= 0)
|
|
num_if += rv;
|
|
else
|
|
printf("ERROR: failed to initialize PCI Ethernet.\n");
|
|
|
|
return num_if;
|
|
}
|