u-boot/include/configs/qemu-ppce500.h
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

144 lines
3.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2011-2014 Freescale Semiconductor, Inc.
*/
/*
* Corenet DS style board configuration file
*/
#ifndef __QEMU_PPCE500_H
#define __QEMU_PPCE500_H
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#define CONFIG_SYS_RAMBOOT
#define CONFIG_PCI1 1 /* PCI controller 1 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
/* Needed to fill the ccsrbar pointer */
/* Virtual address to CCSRBAR */
#define CONFIG_SYS_CCSRBAR 0xe0000000
/* Physical address should be a function call */
#ifndef __ASSEMBLY__
extern unsigned long long get_phys_ccsrbar_addr_early(void);
#define CONFIG_SYS_CCSRBAR_PHYS_HIGH (get_phys_ccsrbar_addr_early() >> 32)
#define CONFIG_SYS_CCSRBAR_PHYS_LOW get_phys_ccsrbar_addr_early()
#else
#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#endif
/* Virtual address range for PCI region maps */
#define CONFIG_SYS_PCI_MAP_START 0x80000000
#define CONFIG_SYS_PCI_MAP_END 0xe8000000
/* Virtual address to a temporary map if we need it (max 128MB) */
#define CONFIG_SYS_TMPVIRT 0xe8000000
/*
* DDR Setup
*/
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_CHIP_SELECTS_PER_CTRL 0
#define CONFIG_SYS_CLK_FREQ 33000000
#define CONFIG_SYS_BOOT_BLOCK 0x00000000 /* boot TLB */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_HWCONFIG
#define CONFIG_SYS_INIT_RAM_ADDR 0x00100000
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0x0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0x00100000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
#define CONFIG_LBA48
/*
* Environment
*/
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO /* echo on for serial download */
/*
* Command line configuration.
*/
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/*
* Environment Configuration
*/
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTCOMMAND \
"test -n \"$qemu_kernel_addr\" && bootm $qemu_kernel_addr - $fdt_addr_r\0"
#endif /* __QEMU_PPCE500_H */