u-boot/include/configs/lacie_kw.h
Patrick Delaunay abe66b1b5d Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:59 -04:00

156 lines
3.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
*/
#ifndef _CONFIG_LACIE_KW_H
#define _CONFIG_LACIE_KW_H
/*
* Machine number definition
*/
#if defined(CONFIG_INETSPACE_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_INETSPACE_V2
#elif defined(CONFIG_NETSPACE_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_V2
#elif defined(CONFIG_NETSPACE_LITE_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_LITE_V2
#elif defined(CONFIG_NETSPACE_MINI_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MINI_V2
#elif defined(CONFIG_NETSPACE_MAX_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MAX_V2
#elif defined(CONFIG_D2NET_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_D2NET_V2
#elif defined(CONFIG_NET2BIG_V2)
#define CONFIG_MACH_TYPE MACH_TYPE_NET2BIG_V2
#else
#error "Unknown board"
#endif
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
/* SoC name */
#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
#define CONFIG_KW88F6192
#else
#define CONFIG_KW88F6281
#endif
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
* Core clock definition
*/
#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
/*
* SDRAM configuration
*/
/*
* Different SDRAM configuration and size for some of the boards derived
* from the Network Space v2
*/
#if defined(CONFIG_INETSPACE_V2)
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
#endif
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/* Remove or override few declarations from mv-common.h */
#undef CONFIG_SYS_IDE_MAXBUS
#undef CONFIG_SYS_IDE_MAXDEVICE
/*
* Enable platform initialisation via misc_init_r() function
*/
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_NETCONSOLE
#endif
/*
* SATA Driver configuration
*/
#ifdef CONFIG_MVSATA_IDE
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
defined(CONFIG_NET2BIG_V2)
#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
#define CONFIG_SYS_IDE_MAXBUS 2
#define CONFIG_SYS_IDE_MAXDEVICE 2
#else
#define CONFIG_SYS_IDE_MAXBUS 1
#define CONFIG_SYS_IDE_MAXDEVICE 1
#endif
#endif /* CONFIG_MVSATA_IDE */
/*
* Enable GPI0 support
*/
#define CONFIG_KIRKWOOD_GPIO
/*
* Enable I2C support
*/
#ifdef CONFIG_CMD_I2C
/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
#if defined(CONFIG_NET2BIG_V2)
#define CONFIG_SYS_I2C_G762_ADDR 0x3e
#endif
#endif /* CONFIG_CMD_I2C */
/*
* Partition support
*/
/*
* File systems support
*/
/*
* Environment variables configurations
*/
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64KB */
#define CONFIG_ENV_SIZE 0x1000 /* 4KB */
#define CONFIG_ENV_ADDR 0x70000
#define CONFIG_ENV_OFFSET 0x70000 /* env starts here */
/*
* Default environment variables
*/
#define CONFIG_BOOTCOMMAND \
"dhcp && run netconsole; " \
"if run usbload || run diskload; then bootm; fi"
#define CONFIG_EXTRA_ENV_SETTINGS \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0" \
"bootfile=uImage\0" \
"loadaddr=0x800000\0" \
"autoload=no\0" \
"netconsole=" \
"set stdin $stdin,nc; " \
"set stdout $stdout,nc; " \
"set stderr $stderr,nc;\0" \
"diskload=ide reset && " \
"ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
"usbload=usb start && " \
"fatload usb 0:1 $loadaddr /boot/$bootfile\0"
#endif /* _CONFIG_LACIE_KW_H */