u-boot/board/freescale/ls1021aiot
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
..
dcu.c SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
Kconfig NXP: Introduce board/freescale/common/Kconfig and migrate CHAIN_OF_TRUST 2017-01-24 10:33:59 -05:00
ls102xa_pbi.cfg armv7: Add support of ls1021a-iot board 2016-11-21 09:20:32 -08:00
ls102xa_rcw_sd.cfg armv7: Add support of ls1021a-iot board 2016-11-21 09:20:32 -08:00
ls1021aiot.c SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
MAINTAINERS armv7: Add support of ls1021a-iot board 2016-11-21 09:20:32 -08:00
Makefile SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
psci.S SPDX: Convert all of our single license tags to Linux Kernel style 2018-05-07 09:34:12 -04:00
README armv7: Add support of ls1021a-iot board 2016-11-21 09:20:32 -08:00

Overview
--------
The LS1021A-IOT is a Freescale reference board that hosts
the LS1021A SoC.

LS1021AIOT board Overview
-------------------------
 - DDR Controller
	- Supports 1GB un-buffered DDR3L SDRAM discrete
	devices(32-bit bus) with 4 bit ECC
	- DDR power supplies 1.35V to all devices with
	automatic tracking of VTT
	- Soldered DDR chip
	- Supprot one fixed speed
 - Ethernet
	- Two on-board SGMII 10/100/1G ethernet ports
	- One Gbit Etherent RGMII interface to 4-ports switch
	with 4x 10/100/1000 RJ145 ports
 - CPLD
	- 8-bit registers in CPLD for system configuration
	- connected to IFC_AD[0:7]
 - Power Supplies
	- 12V@5A DC
 - SDHC
	- SDHC port connects directly to a full 8-bit SD/MMC slot
	- Support for SDIO devices
 - USB
	- Two on-board USB 3.0
	- One on-board USB k22
 - PCIe
	- Two MiniPCIe Solts
 - SATA
	- Support SATA Connector
 - AUDIO
	- AUDIO in and out
 - I/O Expansion
	- Arduino Shield Connector
	- Port0 - CAN/GPIO/Flextimer
	- Port1 - GPIO/CPLD Expansion
	- Port2 - SPI/I2C/UART

Memory map
-----------
The addresses in brackets are physical addresses.

Start Address	End Address		Description			Size
0x00_0100_0000	0x00_0FFF_FFFF	CCSRBAR				240MB
0x00_4000_0000	0x00_43FF_FFFF	QSPI(Chip select 0)	64MB
0x00_4400_0000	0x00_47FF_FFFF	QSPI(Chip select 1)	64MB
0x00_6000_0000	0x00_6000_FFFF	CPLD				64K
0x00_8000_0000	0x00_BFFF_FFFF	DDR					1GB

Boot description
-----------------
LS1021A-IOT support two ways of boot:
Qspi boot and SD boot
The board doesn't support boot from another
source without changing any switch/jumper.