u-boot/doc/README.mpc8360emds
2006-11-30 18:02:20 +01:00

126 lines
3.5 KiB
Text

Freescale MPC8360EMDS Board
-----------------------------------------
1. Board Switches and Jumpers
1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC8360EMDS board
For some reason, the HW designers describe the switch settings
in terms of 0 and 1, and then map that to physical switches where
the label "On" refers to logic 0 and "Off" is logic 1.
Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
bits may contribute to signals that are numbered based at 0,
and some of those signals may be high-bit-number-0 too. Heed
well the names and labels and do not get confused.
"Off" == 1
"On" == 0
SW18 is switch 18 as silk-screened onto the board.
SW4[8] is the bit labled 8 on Switch 4.
SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2.
SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3.
SW3[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On"
and bits labeled 8 is set as "Off".
1.1 For the MPC8360E PB PROTO Board
First, make sure the board default setting is consistent with the
document shipped with your board. Then apply the following setting:
SW3[1-8]= 0000_0100 (HRCW setting value is performed on local bus)
SW4[1-8]= 0011_0000 (Flash boot on local bus)
SW9[1-8]= 0110_0110 (PCI Mode enabled. HRCW is read from FLASH)
SW10[1-8]= 0000_1000 (core PLL setting)
SW11[1-8]= 0000_0100 (SW11 is on the another side of the board)
JP6 1-2
on board Oscillator: 66M
2. Memory Map
2.1. The memory map should look pretty much like this:
0x0000_0000 0x7fff_ffff DDR 2G
0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M
0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M
0xc000_0000 0xdfff_ffff Empty 512M
0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M
0xe020_0000 0xe02f_ffff Empty 1M
0xe030_0000 0xe03f_ffff PCI IO 1M
0xe040_0000 0xefff_ffff Empty 252M
0xf000_0000 0xf3ff_ffff Local Bus SDRAM 64M
0xf400_0000 0xf7ff_ffff Empty 64M
0xf800_0000 0xf800_7fff BCSR on CS1 32K
0xf800_8000 0xf800_ffff PIB CS4 32K
0xf801_0000 0xf801_7fff PIB CS5 32K
0xfe00_0000 0xfeff_ffff FLASH on CS0 16M
3. Definitions
3.1 Explanation of NEW definitions in:
include/configs/MPC8360EMDS.h
CONFIG_MPC83XX MPC83xx family for both MPC8349 and MPC8360
CONFIG_MPC8360 MPC8360 specific
CONFIG_MPC8360EMDS MPC8360EMDS board specific
4. Compilation
Assuming you're using BASH shell:
export CROSS_COMPILE=your-cross-compile-prefix
cd u-boot
make distclean
make MPC8360EMDS_config
make
MPC8360 support PCI in host and slave mode.
To make u-boot support PCI host 66M :
1) DIP SW support PCI mode as described in Section 1.1.
2) Make MPC8360EMDS_HOST_66_config
To make u-boot support PCI host 33M :
1) DIP SW setting is similar as Section 1.1, except for SW3[4] is 1
2) Make MPC8360EMDS_HOST_33_config
To make u-boot support PCI slave 66M :
1) DIP SW setting is similar as Section 1.1, except for SW9[3] is 1
2) Make MPC8360EMDS_SLAVE_config
5. Downloading and Flashing Images
5.0 Download over serial line using Kermit:
loadb
[Drop to kermit:
^\c
send <u-boot-bin-image>
c
]
Or via tftp:
tftp 10000 u-boot.bin
5.1 Reflash U-boot Image using U-boot
tftp 20000 u-boot.bin
protect off fef00000 fef3ffff
erase fef00000 fef3ffff
cp.b 20000 fef00000 xxxx
or
cp.b 20000 fef00000 3ffff
You have to supply the correct byte count with 'xxxx' from the TFTP result log.
Maybe 3ffff will work too, that corresponds to the erased sectors.
6. Notes
1) The console baudrate for MPC8360EMDS is 115200bps.