mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-13 08:27:23 +00:00
22052c6236
This parameter should also be supported. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
94 lines
3.6 KiB
Text
94 lines
3.6 KiB
Text
SPI (Serial Peripheral Interface) busses
|
|
|
|
SPI busses can be described with a node for the SPI master device
|
|
and a set of child nodes for each SPI slave on the bus. For this
|
|
discussion, it is assumed that the system's SPI controller is in
|
|
SPI master mode. This binding does not describe SPI controllers
|
|
in slave mode.
|
|
|
|
The SPI master node requires the following properties:
|
|
- #address-cells - number of cells required to define a chip select
|
|
address on the SPI bus.
|
|
- #size-cells - should be zero.
|
|
- compatible - name of SPI bus controller following generic names
|
|
recommended practice.
|
|
- cs-gpios - (optional) gpios chip select.
|
|
No other properties are required in the SPI bus node. It is assumed
|
|
that a driver for an SPI bus device will understand that it is an SPI bus.
|
|
However, the binding does not attempt to define the specific method for
|
|
assigning chip select numbers. Since SPI chip select configuration is
|
|
flexible and non-standardized, it is left out of this binding with the
|
|
assumption that board specific platform code will be used to manage
|
|
chip selects. Individual drivers can define additional properties to
|
|
support describing the chip select layout.
|
|
|
|
Optional property:
|
|
- num-cs : total number of chipselects
|
|
|
|
If cs-gpios is used the number of chip select will automatically increased
|
|
with max(cs-gpios > hw cs)
|
|
|
|
So if for example the controller has 2 CS lines, and the cs-gpios
|
|
property looks like this:
|
|
|
|
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
|
|
|
|
Then it should be configured so that num_chipselect = 4 with the
|
|
following mapping:
|
|
|
|
cs0 : &gpio1 0 0
|
|
cs1 : native
|
|
cs2 : &gpio1 1 0
|
|
cs3 : &gpio1 2 0
|
|
|
|
SPI slave nodes must be children of the SPI master node and can
|
|
contain the following properties.
|
|
- reg - (required) chip select address of device.
|
|
- compatible - (required) name of SPI device following generic names
|
|
recommended practice
|
|
- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
|
|
- spi-cpol - (optional) Empty property indicating device requires
|
|
inverse clock polarity (CPOL) mode
|
|
- spi-cpha - (optional) Empty property indicating device requires
|
|
shifted clock phase (CPHA) mode
|
|
- spi-cs-high - (optional) Empty property indicating device requires
|
|
chip select active high
|
|
- spi-3wire - (optional) Empty property indicating device requires
|
|
3-wire mode.
|
|
- spi-tx-bus-width - (optional) The bus width(number of data wires) that
|
|
used for MOSI. Defaults to 1 if not present.
|
|
- spi-rx-bus-width - (optional) The bus width(number of data wires) that
|
|
used for MISO. Defaults to 1 if not present.
|
|
- spi-half-duplex - (optional) Indicates that the SPI bus should wait for
|
|
a header byte before reading data from the slave.
|
|
|
|
Some SPI controllers and devices support Dual and Quad SPI transfer mode.
|
|
It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD).
|
|
Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is
|
|
only 1(SINGLE), 2(DUAL) and 4(QUAD).
|
|
Dual/Quad mode is not allowed when 3-wire mode is used.
|
|
|
|
If a gpio chipselect is used for the SPI slave the gpio number will be passed
|
|
via the cs_gpio
|
|
|
|
SPI example for an MPC5200 SPI bus:
|
|
spi@f00 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
|
|
reg = <0xf00 0x20>;
|
|
interrupts = <2 13 0 2 14 0>;
|
|
interrupt-parent = <&mpc5200_pic>;
|
|
|
|
ethernet-switch@0 {
|
|
compatible = "micrel,ks8995m";
|
|
spi-max-frequency = <1000000>;
|
|
reg = <0>;
|
|
};
|
|
|
|
codec@1 {
|
|
compatible = "ti,tlv320aic26";
|
|
spi-max-frequency = <100000>;
|
|
reg = <1>;
|
|
};
|
|
};
|