mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-28 15:41:40 +00:00
29e31c549d
Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The difference lies in whether we enable the boot ROM to use the eMMC reset signal. Depending on the SoC fuse, the boot ROM configures this pin as a GPIO output to drive the reset signal. Our eMMC vs NAND detection currently only sets that signal to a GPIO without explicitly setting any direction. Previously, by default, it was set as an input. As the boot ROM now configures it as an output, we receive a value of zero instead of one, indicating the absence of the pull-up on eMMC modules. To fix this, set the SION bit, allowing the reading back of the value even if it is configured as an output by the boot ROM. It's important to note that with the new SoC fusing, we now read back what the boot ROM drives rather than the real value caused by the pull-up resistor. However, if it were ever driven low, the eMMC would permanently be reset. In addition, remove hard-coded variant in the eMMC build case as since the commit0c39564d02("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant") will anyways always get overridden by the detection routing in board code. Fixes:0c39564d("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant") Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
172 lines
5.6 KiB
C
172 lines
5.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2016-2018 Toradex AG
|
|
*
|
|
* Configuration settings for the Colibri iMX7 module.
|
|
*
|
|
* based on mx7dsabresd.h:
|
|
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
#ifndef __COLIBRI_IMX7_CONFIG_H
|
|
#define __COLIBRI_IMX7_CONFIG_H
|
|
|
|
#include "mx7_common.h"
|
|
|
|
/* MMC Config*/
|
|
#define CFG_SYS_FSL_ESDHC_ADDR 0
|
|
#ifdef CONFIG_TARGET_COLIBRI_IMX7_NAND
|
|
#define CFG_SYS_FSL_USDHC_NUM 1
|
|
#elif CONFIG_TARGET_COLIBRI_IMX7_EMMC
|
|
#define CFG_SYS_FSL_USDHC_NUM 2
|
|
#endif
|
|
|
|
#if defined(CONFIG_TARGET_COLIBRI_IMX7_EMMC)
|
|
#define UBOOT_UPDATE \
|
|
"uboot_hwpart=1\0" \
|
|
"uboot_blk=2\0" \
|
|
"set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
|
|
"setexpr blkcnt ${blkcnt} / 0x200\0" \
|
|
"update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
|
|
"mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0"
|
|
#elif defined(CONFIG_TARGET_COLIBRI_IMX7_NAND)
|
|
#define UBOOT_UPDATE \
|
|
"update_uboot=nand erase.part u-boot1 && " \
|
|
"nand write ${loadaddr} u-boot1 ${filesize} && " \
|
|
"nand erase.part u-boot2 && " \
|
|
"nand write ${loadaddr} u-boot2 ${filesize}\0"
|
|
#endif
|
|
|
|
#ifndef PARTS_DEFAULT
|
|
/* Define the default GPT table for eMMC */
|
|
#define PARTS_DEFAULT \
|
|
/* Android partitions */ \
|
|
"partitions_android=" \
|
|
"uuid_disk=${uuid_gpt_disk};" \
|
|
"name=boot,start=1M,size=32M,uuid=${uuid_gpt_boot};" \
|
|
"name=environment,size=4M,uuid=${uuid_gpt_environment};" \
|
|
"name=recovery,size=16M,uuid=${uuid_gpt_recovery};" \
|
|
"name=system,size=1536M,uuid=${uuid_gpt_system};" \
|
|
"name=cache,size=512M,uuid=${uuid_gpt_cache};" \
|
|
"name=device,size=8M,uuid=${uuid_gpt_device};" \
|
|
"name=misc,size=4M,uuid=${uuid_gpt_misc};" \
|
|
"name=datafooter,size=2M,uuid=${uuid_gpt_datafooter};" \
|
|
"name=metadata,size=2M,uuid=${uuid_gpt_metadata};" \
|
|
"name=persistdata,size=2M,uuid=${uuid_gpt_persistdata};" \
|
|
"name=userdata,size=128M,uuid=${uuid_gpt_userdata};" \
|
|
"name=fbmisc,size=-,uuid=${uuid_gpt_fbmisc}\0"
|
|
#endif /* PARTS_DEFAULT */
|
|
|
|
#define EMMC_ANDROID_BOOTCMD \
|
|
"android_args=androidboot.storage_type=emmc\0" \
|
|
PARTS_DEFAULT \
|
|
"android_fdt_addr=0x83700000\0" \
|
|
"android_mmc_dev=0\0" \
|
|
"m4binary=rpmsg_imu_freertos.elf\0" \
|
|
"androidboot=ext4load mmc 0:a ${loadaddr} media/0/${m4binary}; "\
|
|
"bootaux ${loadaddr}; " \
|
|
"setenv loadaddr 0x88000000; " \
|
|
"setenv bootm_boot_mode sec;" \
|
|
"setenv bootargs androidboot.serialno=${serial#} " \
|
|
"$android_args; " \
|
|
"part start mmc ${android_mmc_dev} boot boot_start; " \
|
|
"part size mmc ${android_mmc_dev} boot boot_size; " \
|
|
"mmc read ${loadaddr} ${boot_start} ${boot_size}; " \
|
|
"part start mmc ${android_mmc_dev} environment env_start; " \
|
|
"part size mmc ${android_mmc_dev} environment env_size; " \
|
|
"mmc read ${android_fdt_addr} ${env_start} ${env_size}; " \
|
|
"bootm ${loadaddr} ${loadaddr} ${android_fdt_addr}\0 "
|
|
|
|
#define MEM_LAYOUT_ENV_SETTINGS \
|
|
"bootm_size=0x10000000\0" \
|
|
"fdt_addr_r=0x88200000\0" \
|
|
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
|
|
"pxefile_addr_r=0x88300000\0" \
|
|
"ramdisk_addr_r=0x88400000\0" \
|
|
"scriptaddr=0x88280000\0"
|
|
|
|
#define UBI_BOOTCMD \
|
|
"ubiargs=ubi.mtd=ubi root=ubi0:rootfs rootfstype=ubifs " \
|
|
"ubi.fm_autoconvert=1\0" \
|
|
"ubiboot=run setup; " \
|
|
"setenv bootargs ${defargs} ${ubiargs} " \
|
|
"${setupargs} ${vidargs} ${tdxargs}; echo Booting from NAND...; " \
|
|
"ubi part ubi && run m4boot && " \
|
|
"ubi read ${kernel_addr_r} kernel && " \
|
|
"ubi read ${fdt_addr_r} dtb && " \
|
|
"run fdt_fixup && bootz ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
|
|
|
#if defined(CONFIG_TARGET_COLIBRI_IMX7_NAND)
|
|
#define MODULE_EXTRA_ENV_SETTINGS \
|
|
UBI_BOOTCMD
|
|
#elif defined(CONFIG_TARGET_COLIBRI_IMX7_EMMC)
|
|
#define MODULE_EXTRA_ENV_SETTINGS \
|
|
EMMC_ANDROID_BOOTCMD
|
|
#endif
|
|
|
|
#if defined(CONFIG_TARGET_COLIBRI_IMX7_NAND)
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 0) \
|
|
func(USB, usb, 0) \
|
|
func(DHCP, dhcp, na)
|
|
#elif defined(CONFIG_TARGET_COLIBRI_IMX7_EMMC)
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 1) \
|
|
func(MMC, mmc, 0) \
|
|
func(USB, usb, 0) \
|
|
func(DHCP, dhcp, na)
|
|
#endif
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
#define CFG_EXTRA_ENV_SETTINGS \
|
|
BOOTENV \
|
|
MEM_LAYOUT_ENV_SETTINGS \
|
|
MODULE_EXTRA_ENV_SETTINGS \
|
|
UBOOT_UPDATE \
|
|
"boot_file=zImage\0" \
|
|
"boot_script_dhcp=boot.scr\0" \
|
|
"console=ttymxc0\0" \
|
|
"defargs=\0" \
|
|
"fdt_board=eval-v3\0" \
|
|
"fdt_fixup=;\0" \
|
|
"m4boot=;\0" \
|
|
"ip_dyn=yes\0" \
|
|
"kernel_file=zImage\0" \
|
|
"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
|
|
"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
|
|
"${board}/flash_eth.img && source ${loadaddr}\0" \
|
|
"setsdupdate=mmc rescan && setenv interface mmc && " \
|
|
"fatload ${interface} 0:1 ${loadaddr} " \
|
|
"${board}/flash_blk.img && source ${loadaddr}\0" \
|
|
"setup=setenv setupargs " \
|
|
"console=tty1 console=${console}" \
|
|
",${baudrate}n8 ${memargs} ${mtdparts} consoleblank=0\0" \
|
|
"setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
|
|
"setusbupdate=usb start && setenv interface usb && " \
|
|
"fatload ${interface} 0:1 ${loadaddr} " \
|
|
"${board}/flash_blk.img && source ${loadaddr}\0" \
|
|
"splashpos=m,m\0" \
|
|
"splashimage=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
|
|
"videomode=video=ctfb:x:640,y:480,depth:18,pclk:39722,le:48,ri:16,up:33,lo:10,hs:96,vs:2,sync:0,vmode:0\0" \
|
|
"updlevel=2\0"
|
|
|
|
/* Miscellaneous configurable options */
|
|
|
|
/* Physical Memory Map */
|
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
|
|
|
|
#define CFG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CFG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CFG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
#ifdef CONFIG_TARGET_COLIBRI_IMX7_NAND
|
|
/* NAND stuff */
|
|
#define CFG_SYS_NAND_BASE 0x40000000
|
|
#endif
|
|
|
|
/* USB Configs */
|
|
|
|
#define CFG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CFG_MXC_USB_FLAGS 0
|
|
|
|
#endif
|