u-boot/include/configs/am3517_evm.h
Simon Glass 2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00

314 lines
9.6 KiB
C

/*
* am3517_evm.h - Default configuration for AM3517 EVM board.
*
* Author: Vaibhav Hiremath <hvaibhav@ti.com>
*
* Based on omap3_evm_config.h
*
* Copyright (C) 2010 Texas Instruments Incorporated
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
* header. That is 0x800FFFC0--0x80100000 should not be used for any
* other needs.
*/
#define CONFIG_SYS_TEXT_BASE 0x80100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap.h>
#define CONFIG_MISC_INIT_R
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (16 << 20)
/* Hardware drivers */
/* NS16550 Configuration */
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
/* select serial console configuration */
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SERIAL3 3 /* UART3 on AM3517 EVM */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
/*
* USB configuration
* Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard
* Enable CONFIG_USB_MUSB_GADGET for Device functionalities.
*/
#define CONFIG_USB_MUSB_AM35X
#define CONFIG_USB_MUSB_PIO_ONLY
#ifdef CONFIG_USB_MUSB_AM35X
#ifdef CONFIG_USB_MUSB_HOST
#ifdef CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_PREBOOT "usb start"
#endif /* CONFIG_USB_KEYBOARD */
#endif /* CONFIG_USB_MUSB_HOST */
#ifdef CONFIG_USB_MUSB_GADGET
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_RNDIS
#endif /* CONFIG_USB_MUSB_GADGET */
#endif /* CONFIG_USB_MUSB_AM35X */
/* commands to include */
#define CONFIG_CMD_NAND
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
#define CONFIG_SYS_I2C_OMAP34XX
/* Ethernet */
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_DRIVER_TI_EMAC_USE_RMII
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
/* Board NAND Info. */
#ifdef CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_GPMC_PREFETCH
#define CONFIG_BCH
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access */
/* nand at CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
11, 12, 13, 14, 16, 17, 18, 19, 20, \
21, 22, 23, 24, 25, 26, 27, 28, 30, \
31, 32, 33, 34, 35, 36, 37, 38, 39, \
40, 41, 42, 44, 45, 46, 47, 48, 49, \
50, 51, 52, 53, 54, 55, 56 }
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
/* NAND block size is 128 KiB. Synchronize these values with
* corresponding Device Tree entries in Linux:
* MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
* U-Boot 15 * NAND_BLOCK_SIZE = 1920 KiB @ 0x080000
* U-Boot environment 2 * NAND_BLOCK_SIZE = 256 KiB @ 0x260000
* Kernel 64 * NAND_BLOCK_SIZE = 8 MiB @ 0x2A0000
* DTB 4 * NAND_BLOCK_SIZE = 512 KiB @ 0xAA0000
* RootFS Remaining Flash Space @ 0xB20000
*/
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
"512k(MLO)," \
"1920k(u-boot)," \
"256k(u-boot-env)," \
"8m(kernel)," \
"512k(dtb)," \
"-(rootfs)"
#else
#define MTDIDS_DEFAULT
#define MTDPARTS_DEFAULT
#endif /* CONFIG_NAND */
/* Environment information */
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"console=ttyO2,115200n8\0" \
"fdtfile=am3517-evm.dtb\0" \
"fdtaddr=0x82C00000\0" \
"vram=16M\0" \
"bootenv=uEnv.txt\0" \
"cmdline=\0" \
"optargs=\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
"mmcpart=1\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext4 rootwait fixrtc\0" \
"mmcargs=setenv bootargs console=${console} " \
"${mtdparts} " \
"${optargs} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype} " \
"${cmdline}\0" \
"nandargs=setenv bootargs console=${console} " \
"${mtdparts} " \
"${optargs} " \
"root=ubi0:rootfs rw ubi.mtd=rootfs " \
"rootfstype=ubifs rootwait " \
"${cmdline}\0" \
"loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootenv}\0"\
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t ${loadaddr} ${filesize}\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootfile}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdtaddr} ${fdtfile}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootz ${loadaddr} - ${fdtaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nand read ${loadaddr} 2a0000 800000; " \
"nand read ${fdtaddr} aa0000 80000; " \
"bootm ${loadaddr} - ${fdtaddr}\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"echo SD/MMC found on device $mmcdev; " \
"if run loadbootenv; then " \
"run importbootenv; " \
"fi; " \
"echo Checking if uenvcmd is set ...; " \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...; " \
"run uenvcmd; " \
"fi; " \
"echo Running default loadimage ...; " \
"setenv bootfile zImage; " \
"if run loadimage; then " \
"run loadfdt; " \
"run mmcboot; " \
"fi; " \
"else run nandboot; fi"
/* Miscellaneous configurable options */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
/* We set the max number of command args high to avoid HUSH bugs. */
#define CONFIG_SYS_MAXARGS 64
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 512
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
/* address */
/*
* AM3517 has 12 GP timers, they can be driven by the system clock
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
* This rate is divided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
/* Physical Memory Map */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
/* FLASH and environment organization */
/* **** PISMO SUPPORT *** */
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
/* on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#if defined(CONFIG_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_ENV_SIZE CONFIG_SYS_ENV_SECT_SIZE
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_TEXT_BASE 0x40200000
#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
CONFIG_SPL_TEXT_BASE)
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds"
#endif /* __CONFIG_H */