mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-26 21:13:48 +00:00
595ea7381b
If early firmware initialized the display hardware and the display controllers are scanning out a framebuffer (e.g. a splash screen), make sure to pass information about the memory location of that framebuffer to the kernel before booting to avoid the kernel from using that memory for the buddy allocator. This same mechanism can also be used in the kernel to set up early SMMU mappings and avoid SMMU faults caused by the display controller reading from memory for which it has no mapping. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
193 lines
4.5 KiB
C
193 lines
4.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2013-2015
|
|
* NVIDIA Corporation <www.nvidia.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <environment.h>
|
|
#include <fdtdec.h>
|
|
#include <i2c.h>
|
|
#include <linux/libfdt.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/pinmux.h>
|
|
#include <asm/arch-tegra/cboot.h>
|
|
#include "../p2571/max77620_init.h"
|
|
#include "pinmux-config-p2371-2180.h"
|
|
|
|
void pin_mux_mmc(void)
|
|
{
|
|
struct udevice *dev;
|
|
uchar val;
|
|
int ret;
|
|
|
|
/* Turn on MAX77620 LDO2 to 3.3V for SD card power */
|
|
debug("%s: Set LDO2 for VDDIO_SDMMC_AP power to 3.3V\n", __func__);
|
|
ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
|
|
if (ret) {
|
|
printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
|
|
return;
|
|
}
|
|
/* 0xF2 for 3.3v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
|
|
val = 0xF2;
|
|
ret = dm_i2c_write(dev, MAX77620_CNFG1_L2_REG, &val, 1);
|
|
if (ret)
|
|
printf("i2c_write 0 0x3c 0x27 failed: %d\n", ret);
|
|
|
|
/* Disable LDO4 discharge */
|
|
ret = dm_i2c_read(dev, MAX77620_CNFG2_L4_REG, &val, 1);
|
|
if (ret) {
|
|
printf("i2c_read 0 0x3c 0x2c failed: %d\n", ret);
|
|
} else {
|
|
val &= ~BIT(1); /* ADE */
|
|
ret = dm_i2c_write(dev, MAX77620_CNFG2_L4_REG, &val, 1);
|
|
if (ret)
|
|
printf("i2c_write 0 0x3c 0x2c failed: %d\n", ret);
|
|
}
|
|
|
|
/* Set MBLPD */
|
|
ret = dm_i2c_read(dev, MAX77620_CNFGGLBL1_REG, &val, 1);
|
|
if (ret) {
|
|
printf("i2c_write 0 0x3c 0x00 failed: %d\n", ret);
|
|
} else {
|
|
val |= BIT(6); /* MBLPD */
|
|
ret = dm_i2c_write(dev, MAX77620_CNFGGLBL1_REG, &val, 1);
|
|
if (ret)
|
|
printf("i2c_write 0 0x3c 0x00 failed: %d\n", ret);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Routine: pinmux_init
|
|
* Description: Do individual peripheral pinmux configs
|
|
*/
|
|
void pinmux_init(void)
|
|
{
|
|
pinmux_clear_tristate_input_clamping();
|
|
|
|
gpio_config_table(p2371_2180_gpio_inits,
|
|
ARRAY_SIZE(p2371_2180_gpio_inits));
|
|
|
|
pinmux_config_pingrp_table(p2371_2180_pingrps,
|
|
ARRAY_SIZE(p2371_2180_pingrps));
|
|
|
|
pinmux_config_drvgrp_table(p2371_2180_drvgrps,
|
|
ARRAY_SIZE(p2371_2180_drvgrps));
|
|
}
|
|
|
|
#ifdef CONFIG_PCI_TEGRA
|
|
int tegra_pcie_board_init(void)
|
|
{
|
|
struct udevice *dev;
|
|
uchar val;
|
|
int ret;
|
|
|
|
/* Turn on MAX77620 LDO1 to 1.05V for PEX power */
|
|
debug("%s: Set LDO1 for PEX power to 1.05V\n", __func__);
|
|
ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
|
|
if (ret) {
|
|
printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
|
|
return -1;
|
|
}
|
|
/* 0xCA for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
|
|
val = 0xCA;
|
|
ret = dm_i2c_write(dev, MAX77620_CNFG1_L1_REG, &val, 1);
|
|
if (ret)
|
|
printf("i2c_write 0 0x3c 0x25 failed: %d\n", ret);
|
|
|
|
return 0;
|
|
}
|
|
#endif /* PCI */
|
|
|
|
static void ft_mac_address_setup(void *fdt)
|
|
{
|
|
const void *cboot_fdt = (const void *)cboot_boot_x0;
|
|
uint8_t mac[ETH_ALEN], local_mac[ETH_ALEN];
|
|
const char *path;
|
|
int offset, err;
|
|
|
|
err = cboot_get_ethaddr(cboot_fdt, local_mac);
|
|
if (err < 0)
|
|
memset(local_mac, 0, ETH_ALEN);
|
|
|
|
path = fdt_get_alias(fdt, "ethernet");
|
|
if (!path)
|
|
return;
|
|
|
|
debug("ethernet alias found: %s\n", path);
|
|
|
|
offset = fdt_path_offset(fdt, path);
|
|
if (offset < 0) {
|
|
printf("ethernet alias points to absent node %s\n", path);
|
|
return;
|
|
}
|
|
|
|
if (is_valid_ethaddr(local_mac)) {
|
|
err = fdt_setprop(fdt, offset, "local-mac-address", local_mac,
|
|
ETH_ALEN);
|
|
if (!err)
|
|
debug("Local MAC address set: %pM\n", local_mac);
|
|
}
|
|
|
|
if (eth_env_get_enetaddr("ethaddr", mac)) {
|
|
if (memcmp(local_mac, mac, ETH_ALEN) != 0) {
|
|
err = fdt_setprop(fdt, offset, "mac-address", mac,
|
|
ETH_ALEN);
|
|
if (!err)
|
|
debug("MAC address set: %pM\n", mac);
|
|
}
|
|
}
|
|
}
|
|
|
|
static int ft_copy_carveout(void *dst, const void *src, const char *node)
|
|
{
|
|
struct fdt_memory fb;
|
|
int err;
|
|
|
|
err = fdtdec_get_carveout(src, node, "memory-region", 0, &fb);
|
|
if (err < 0) {
|
|
if (err != -FDT_ERR_NOTFOUND)
|
|
printf("failed to get carveout for %s: %d\n", node,
|
|
err);
|
|
|
|
return err;
|
|
}
|
|
|
|
err = fdtdec_set_carveout(dst, node, "memory-region", 0, "framebuffer",
|
|
&fb);
|
|
if (err < 0) {
|
|
printf("failed to set carveout for %s: %d\n", node, err);
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ft_carveout_setup(void *fdt)
|
|
{
|
|
const void *cboot_fdt = (const void *)cboot_boot_x0;
|
|
static const char * const nodes[] = {
|
|
"/host1x@50000000/dc@54200000",
|
|
"/host1x@50000000/dc@54240000",
|
|
};
|
|
unsigned int i;
|
|
int err;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(nodes); i++) {
|
|
err = ft_copy_carveout(fdt, cboot_fdt, nodes[i]);
|
|
if (err < 0) {
|
|
if (err != -FDT_ERR_NOTFOUND)
|
|
printf("failed to copy carveout for %s: %d\n",
|
|
nodes[i], err);
|
|
continue;
|
|
}
|
|
}
|
|
}
|
|
|
|
int ft_board_setup(void *fdt, bd_t *bd)
|
|
{
|
|
ft_mac_address_setup(fdt);
|
|
ft_carveout_setup(fdt);
|
|
|
|
return 0;
|
|
}
|