u-boot/board/Marvell/db-mv784mp-gp/db-mv784mp-gp.c
Stefan Roese e3b9c98a23 net: mvneta: Convert to driver model
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.

With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:

PHY-mode ("phy-mode") and PHY-address ("reg").

The base addresses for the ethernet controllers can be removed from
the header files as well.

Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
2016-01-14 14:08:59 +01:00

118 lines
3 KiB
C

/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
DECLARE_GLOBAL_DATA_PTR;
#define ETH_PHY_CTRL_REG 0
#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
/*
* Those values and defines are taken from the Marvell U-Boot version
* "u-boot-2011.12-2014_T1.0" for the board rd78460gp aka
* "RD-AXP-GP rev 1.0".
*
* GPPs
* MPP# NAME IN/OUT
* ----------------------------------------------
* 21 SW_Reset_ OUT
* 25 Phy_Int# IN
* 28 SDI_WP IN
* 29 SDI_Status IN
* 54-61 On GPP Connector ?
* 62 Switch Interrupt IN
* 63-65 Reserved from SW Board ?
* 66 SW_BRD connected IN
*/
#define RD_78460_GP_GPP_OUT_ENA_LOW (~(BIT(21) | BIT(20)))
#define RD_78460_GP_GPP_OUT_ENA_MID (~(BIT(26) | BIT(27)))
#define RD_78460_GP_GPP_OUT_ENA_HIGH (~(0x0))
#define RD_78460_GP_GPP_OUT_VAL_LOW (BIT(21) | BIT(20))
#define RD_78460_GP_GPP_OUT_VAL_MID (BIT(26) | BIT(27))
#define RD_78460_GP_GPP_OUT_VAL_HIGH 0x0
int board_early_init_f(void)
{
/* Configure MPP */
writel(0x00000000, MVEBU_MPP_BASE + 0x00);
writel(0x00000000, MVEBU_MPP_BASE + 0x04);
writel(0x33000000, MVEBU_MPP_BASE + 0x08);
writel(0x11000000, MVEBU_MPP_BASE + 0x0c);
writel(0x11111111, MVEBU_MPP_BASE + 0x10);
writel(0x00221100, MVEBU_MPP_BASE + 0x14);
writel(0x00000003, MVEBU_MPP_BASE + 0x18);
writel(0x00000000, MVEBU_MPP_BASE + 0x1c);
writel(0x00000000, MVEBU_MPP_BASE + 0x20);
/* Configure GPIO */
writel(RD_78460_GP_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
writel(RD_78460_GP_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
writel(RD_78460_GP_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
writel(RD_78460_GP_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
writel(RD_78460_GP_GPP_OUT_VAL_HIGH, MVEBU_GPIO2_BASE + 0x00);
writel(RD_78460_GP_GPP_OUT_ENA_HIGH, MVEBU_GPIO2_BASE + 0x04);
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
return 0;
}
int checkboard(void)
{
puts("Board: Marvell DB-MV784MP-GP\n");
return 0;
}
int board_eth_init(bd_t *bis)
{
cpu_eth_init(bis); /* Built in controller(s) come first */
return pci_eth_init(bis);
}
int board_phy_config(struct phy_device *phydev)
{
u16 reg;
/* Enable QSGMII AN */
/* Set page to 4 */
phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 4);
/* Enable AN */
phy_write(phydev, MDIO_DEVAD_NONE, 0x0, 0x1140);
/* Set page to 0 */
phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 0);
/* Phy C_ANEG */
reg = phy_read(phydev, MDIO_DEVAD_NONE, 0x4);
reg |= 0x1E0;
phy_write(phydev, MDIO_DEVAD_NONE, 0x4, reg);
/* Soft-Reset */
phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);
phy_write(phydev, MDIO_DEVAD_NONE, 0, 0x9140);
/* Power up the phy */
reg = phy_read(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG);
reg &= ~(ETH_PHY_CTRL_POWER_DOWN_MASK);
phy_write(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG, reg);
printf("88E1545 Initialized\n");
return 0;
}