u-boot/board/freescale/p1023rdb/p1023rdb.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

153 lines
3.2 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2013 Freescale Semiconductor, Inc.
*
* Authors: Roy Zang <tie-fei.zang@freescale.com>
* Chunhe Lan <Chunhe.Lan@freescale.com>
*/
#include <common.h>
#include <command.h>
#include <pci.h>
#include <asm/io.h>
#include <asm/cache.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
#include <fsl_ddr_sdram.h>
#include <asm/fsl_portals.h>
#include <fsl_qbman.h>
#include <linux/libfdt.h>
#include <fdt_support.h>
#include <netdev.h>
#include <malloc.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <miiphy.h>
#include <phy.h>
#include <fsl_dtsec.h>
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
fsl_lbc_t *lbc = LBC_BASE_ADDR;
/* Set ABSWP to implement conversion of addresses in the LBC */
setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
return 0;
}
int checkboard(void)
{
printf("Board: P1023 RDB\n");
return 0;
}
#ifdef CONFIG_PCI
void pci_init_board(void)
{
fsl_pcie_init_board(0);
}
#endif
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
int flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash + PROMJET region to caching-inhibited
* so that flash can be erased properly.
*/
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
if (flash_esel == -1) {
/* very unlikely unless something is messed up */
puts("Error: Could not find TLB for FLASH BASE\n");
flash_esel = 2; /* give our best effort to continue */
} else {
/* invalidate existing TLB entry for flash + promjet */
disable_tlb(flash_esel);
}
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, flash_esel, BOOKE_PAGESZ_256M, 1);
setup_qbman_portals();
return 0;
}
unsigned long get_board_sys_clk(ulong dummy)
{
return gd->bus_clk;
}
unsigned long get_board_ddr_clk(ulong dummy)
{
return gd->mem_clk;
}
int board_eth_init(bd_t *bis)
{
ccsr_gur_t *gur = (ccsr_gur_t *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
struct fsl_pq_mdio_info dtsec_mdio_info;
/*
* Need to set dTSEC 1 pin multiplexing to TSEC. The default setting
* is not correct.
*/
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TSEC1_1);
dtsec_mdio_info.regs =
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
/* Register the 1G MDIO bus */
fsl_pq_mdio_init(bis, &dtsec_mdio_info);
fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
fm_info_set_mdio(FM1_DTSEC1,
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
fm_info_set_mdio(FM1_DTSEC2,
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
#ifdef CONFIG_FMAN_ENET
cpu_eth_init(bis);
#endif
return pci_eth_init(bis);
}
#if defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, bd_t *bd)
{
phys_addr_t base;
phys_size_t size;
ft_cpu_setup(blob, bd);
base = env_get_bootm_low();
size = env_get_bootm_size();
fdt_fixup_memory(blob, (u64)base, (u64)size);
#ifdef CONFIG_HAS_FSL_DR_USB
fsl_fdt_fixup_dr_usb(blob, bd);
#endif
fdt_fixup_fman_ethernet(blob);
return 0;
}
#endif