mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 11:13:07 +00:00
4e5114daf9
Synchronise device tree with linux v5.19-rc5. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
472 lines
11 KiB
Text
472 lines
11 KiB
Text
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
/*
|
|
* Copyright 2020 Compass Electronics Group, LLC
|
|
*/
|
|
|
|
/ {
|
|
aliases {
|
|
rtc0 = &rtc;
|
|
rtc1 = &snvs_rtc;
|
|
spi0 = &flexspi;
|
|
};
|
|
|
|
usdhc1_pwrseq: usdhc1_pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usdhc1_gpio>;
|
|
reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
|
|
clocks = <&osc_32k>;
|
|
clock-names = "ext_clock";
|
|
post-power-on-delay-ms = <80>;
|
|
};
|
|
|
|
memory@40000000 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x40000000 0 0x80000000>;
|
|
};
|
|
};
|
|
|
|
&A53_0 {
|
|
cpu-supply = <&buck2_reg>;
|
|
};
|
|
|
|
&A53_1 {
|
|
cpu-supply = <&buck2_reg>;
|
|
};
|
|
|
|
&A53_2 {
|
|
cpu-supply = <&buck2_reg>;
|
|
};
|
|
|
|
&A53_3 {
|
|
cpu-supply = <&buck2_reg>;
|
|
};
|
|
|
|
/* DDR controller is running LPDDR at 800MHz which requires 0.95V */
|
|
&a53_opp_table {
|
|
opp-1200000000 {
|
|
opp-microvolt = <950000>;
|
|
};
|
|
};
|
|
|
|
&ddrc {
|
|
operating-points-v2 = <&ddrc_opp_table>;
|
|
|
|
ddrc_opp_table: opp-table {
|
|
compatible = "operating-points-v2";
|
|
|
|
opp-25M {
|
|
opp-hz = /bits/ 64 <25000000>;
|
|
};
|
|
|
|
opp-100M {
|
|
opp-hz = /bits/ 64 <100000000>;
|
|
};
|
|
|
|
opp-800M {
|
|
opp-hz = /bits/ 64 <800000000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&fec1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_fec1>;
|
|
phy-mode = "rgmii-id";
|
|
phy-handle = <ðphy0>;
|
|
phy-supply = <&buck6_reg>;
|
|
phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
|
|
fsl,magic-packet;
|
|
status = "okay";
|
|
|
|
mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ethphy0: ethernet-phy@0 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&flexspi {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_flexspi>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
reg = <0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <80000000>;
|
|
spi-tx-bus-width = <1>;
|
|
spi-rx-bus-width = <4>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <400000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c1>;
|
|
status = "okay";
|
|
|
|
pmic@4b {
|
|
compatible = "rohm,bd71847";
|
|
reg = <0x4b>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_pmic>;
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
|
rohm,reset-snvs-powered;
|
|
#clock-cells = <0>;
|
|
clocks = <&osc_32k 0>;
|
|
clock-output-names = "clk-32k-out";
|
|
|
|
regulators {
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "buck1";
|
|
regulator-min-microvolt = <700000>;
|
|
regulator-max-microvolt = <1300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-ramp-delay = <1250>;
|
|
};
|
|
|
|
buck2_reg: BUCK2 {
|
|
regulator-name = "buck2";
|
|
regulator-min-microvolt = <700000>;
|
|
regulator-max-microvolt = <1300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-ramp-delay = <1250>;
|
|
rohm,dvs-run-voltage = <1000000>;
|
|
rohm,dvs-idle-voltage = <900000>;
|
|
};
|
|
|
|
buck3_reg: BUCK3 {
|
|
// BUCK5 in datasheet
|
|
regulator-name = "buck3";
|
|
regulator-min-microvolt = <700000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck4_reg: BUCK4 {
|
|
// BUCK6 in datasheet
|
|
regulator-name = "buck4";
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck5_reg: BUCK5 {
|
|
// BUCK7 in datasheet
|
|
regulator-name = "buck5";
|
|
regulator-min-microvolt = <1605000>;
|
|
regulator-max-microvolt = <1995000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck6_reg: BUCK6 {
|
|
// BUCK8 in datasheet
|
|
regulator-name = "buck6";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1400000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo1_reg: LDO1 {
|
|
regulator-name = "ldo1";
|
|
regulator-min-microvolt = <1600000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "ldo2";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <900000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo3_reg: LDO3 {
|
|
regulator-name = "ldo3";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo4_reg: LDO4 {
|
|
regulator-name = "ldo4";
|
|
regulator-min-microvolt = <900000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo6_reg: LDO6 {
|
|
regulator-name = "ldo6";
|
|
regulator-min-microvolt = <900000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c3 {
|
|
clock-frequency = <400000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c3>;
|
|
status = "okay";
|
|
|
|
eeprom@50 {
|
|
compatible = "microchip,24c64", "atmel,24c64";
|
|
pagesize = <32>;
|
|
read-only; /* Manufacturing EEPROM programmed at factory */
|
|
reg = <0x50>;
|
|
};
|
|
|
|
rtc: rtc@51 {
|
|
compatible = "nxp,pcf85263";
|
|
reg = <0x51>;
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart1>;
|
|
assigned-clocks = <&clk IMX8MN_CLK_UART1>;
|
|
assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
|
|
uart-has-rtscts;
|
|
status = "okay";
|
|
|
|
bluetooth {
|
|
compatible = "brcm,bcm43438-bt";
|
|
shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
|
|
host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
|
|
device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
|
|
clocks = <&osc_32k>;
|
|
max-speed = <4000000>;
|
|
clock-names = "extclk";
|
|
};
|
|
};
|
|
|
|
&usdhc1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-names = "default", "state_100mhz", "state_200mhz";
|
|
pinctrl-0 = <&pinctrl_usdhc1>;
|
|
pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
|
|
pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
|
|
vmmc-supply = <&buck4_reg>;
|
|
vqmmc-supply = <&buck5_reg>;
|
|
bus-width = <4>;
|
|
non-removable;
|
|
cap-power-off-card;
|
|
keep-power-in-suspend;
|
|
mmc-pwrseq = <&usdhc1_pwrseq>;
|
|
status = "okay";
|
|
|
|
brcmf: bcrmf@1 {
|
|
reg = <1>;
|
|
compatible = "brcm,bcm4329-fmac";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_wlan>;
|
|
interrupt-parent = <&gpio2>;
|
|
interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "host-wake";
|
|
};
|
|
};
|
|
|
|
&usdhc3 {
|
|
pinctrl-names = "default", "state_100mhz", "state_200mhz";
|
|
pinctrl-0 = <&pinctrl_usdhc3>;
|
|
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
|
|
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
status = "okay";
|
|
};
|
|
|
|
&wdog1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_wdog>;
|
|
fsl,ext-reset-output;
|
|
status = "okay";
|
|
};
|
|
|
|
&iomuxc {
|
|
pinctrl_fec1: fec1grp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3
|
|
MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
|
|
MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
|
|
MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
|
|
MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
|
|
MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
|
|
MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
|
|
MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
|
|
MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
|
|
MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
|
|
MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
|
|
MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
|
|
MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
|
|
MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
|
|
MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c1: i2c1grp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
|
|
MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c3: i2c3grp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
|
|
MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
|
|
>;
|
|
};
|
|
|
|
pinctrl_flexspi: flexspigrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2
|
|
MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
|
|
MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
|
|
MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
|
|
MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
|
|
MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
|
|
>;
|
|
};
|
|
|
|
pinctrl_pmic: pmicirqgrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141
|
|
>;
|
|
};
|
|
|
|
pinctrl_uart1: uart1grp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
|
|
MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
|
|
MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140
|
|
MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140
|
|
MX8MN_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19
|
|
MX8MN_IOMUXC_SD1_DATA5_GPIO2_IO7 0x19
|
|
MX8MN_IOMUXC_SD1_DATA6_GPIO2_IO8 0x19
|
|
MX8MN_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc1_gpio: usdhc1gpiogrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc1: usdhc1grp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
|
|
MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
|
|
MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
|
|
MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
|
|
MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
|
|
MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
|
|
MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
|
|
MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
|
|
MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
|
|
MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
|
|
MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
|
|
MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
|
|
MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
|
|
MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
|
|
MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
|
|
MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc3: usdhc3grp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
|
|
MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
|
|
MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
|
|
MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
|
|
MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
|
|
MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
|
|
MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
|
|
MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
|
|
MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
|
|
MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
|
|
MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
|
|
MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
|
|
MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
|
|
MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
|
|
MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
|
|
MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
|
|
MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
|
|
MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
|
|
MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
|
|
MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
|
|
MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
|
|
>;
|
|
};
|
|
|
|
pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
|
|
MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
|
|
MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
|
|
MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
|
|
MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
|
|
MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
|
|
MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
|
|
MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
|
|
MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
|
|
MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
|
|
MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
|
|
>;
|
|
};
|
|
|
|
pinctrl_wdog: wdoggrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
|
|
>;
|
|
};
|
|
|
|
pinctrl_wlan: wlangrp {
|
|
fsl,pins = <
|
|
MX8MN_IOMUXC_SD1_DATA7_GPIO2_IO9 0x111
|
|
>;
|
|
};
|
|
};
|