mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 17:41:08 +00:00
e8e35efc8f
Rewrite the assembly serial_early_puts() helper to place the strings in the .rodata section rather than embedding them directly in the .text section. Using .text is a little simpler, but it doesn't let people execute out of internal L1 sram (since core reads don't work on those regions). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
308 lines
8.2 KiB
C
308 lines
8.2 KiB
C
/*
|
|
* serial.h - common serial defines for early debug and serial driver.
|
|
* any functions defined here must be always_inline since
|
|
* initcode cannot have function calls.
|
|
*
|
|
* Copyright (c) 2004-2007 Analog Devices Inc.
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#ifndef __BFIN_CPU_SERIAL_H__
|
|
#define __BFIN_CPU_SERIAL_H__
|
|
|
|
#include <asm/blackfin.h>
|
|
#include <asm/mach-common/bits/uart.h>
|
|
|
|
#ifndef CONFIG_UART_CONSOLE
|
|
# define CONFIG_UART_CONSOLE 0
|
|
#endif
|
|
|
|
#ifdef CONFIG_DEBUG_EARLY_SERIAL
|
|
# define BFIN_DEBUG_EARLY_SERIAL 1
|
|
#else
|
|
# define BFIN_DEBUG_EARLY_SERIAL 0
|
|
#endif
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
#include <asm/portmux.h>
|
|
|
|
#define LOB(x) ((x) & 0xFF)
|
|
#define HIB(x) (((x) >> 8) & 0xFF)
|
|
|
|
#if defined(__ADSPBF50x__) || defined(__ADSPBF54x__)
|
|
# define BFIN_UART_HW_VER 2
|
|
#else
|
|
# define BFIN_UART_HW_VER 1
|
|
#endif
|
|
|
|
/*
|
|
* All Blackfin system MMRs are padded to 32bits even if the register
|
|
* itself is only 16bits. So use a helper macro to streamline this.
|
|
*/
|
|
#define __BFP(m) u16 m; u16 __pad_##m
|
|
struct bfin_mmr_serial {
|
|
#if BFIN_UART_HW_VER == 2
|
|
__BFP(dll);
|
|
__BFP(dlh);
|
|
__BFP(gctl);
|
|
__BFP(lcr);
|
|
__BFP(mcr);
|
|
__BFP(lsr);
|
|
__BFP(msr);
|
|
__BFP(scr);
|
|
__BFP(ier_set);
|
|
__BFP(ier_clear);
|
|
__BFP(thr);
|
|
__BFP(rbr);
|
|
#else
|
|
union {
|
|
u16 dll;
|
|
u16 thr;
|
|
const u16 rbr;
|
|
};
|
|
const u16 __spad0;
|
|
union {
|
|
u16 dlh;
|
|
u16 ier;
|
|
};
|
|
const u16 __spad1;
|
|
const __BFP(iir);
|
|
__BFP(lcr);
|
|
__BFP(mcr);
|
|
__BFP(lsr);
|
|
__BFP(msr);
|
|
__BFP(scr);
|
|
const u32 __spad2;
|
|
__BFP(gctl);
|
|
#endif
|
|
};
|
|
#undef __BFP
|
|
|
|
#define __PASTE_UART(num, pfx, sfx) pfx##num##_##sfx
|
|
#define _PASTE_UART(num, pfx, sfx) __PASTE_UART(num, pfx, sfx)
|
|
#define MMR_UART(n) _PASTE_UART(n, UART, DLL)
|
|
#define _P_UART(n, pin) _PASTE_UART(n, P_UART, pin)
|
|
#define P_UART(pin) _P_UART(CONFIG_UART_CONSOLE, pin)
|
|
|
|
#ifndef UART_DLL
|
|
# define UART_DLL MMR_UART(CONFIG_UART_CONSOLE)
|
|
#else
|
|
# define UART0_DLL UART_DLL
|
|
# if CONFIG_UART_CONSOLE != 0
|
|
# error CONFIG_UART_CONSOLE must be 0 on parts with only one UART
|
|
# endif
|
|
#endif
|
|
#define pUART ((volatile struct bfin_mmr_serial *)uart_base)
|
|
|
|
#if BFIN_UART_HW_VER == 2
|
|
# define ACCESS_LATCH()
|
|
# define ACCESS_PORT_IER()
|
|
#else
|
|
# define ACCESS_LATCH() \
|
|
bfin_write(&pUART->lcr, bfin_read(&pUART->lcr) | DLAB)
|
|
# define ACCESS_PORT_IER() \
|
|
bfin_write(&pUART->lcr, bfin_read(&pUART->lcr) & ~DLAB)
|
|
#endif
|
|
|
|
__attribute__((always_inline))
|
|
static inline void serial_do_portmux(void)
|
|
{
|
|
if (!BFIN_DEBUG_EARLY_SERIAL) {
|
|
const unsigned short pins[] = { P_UART(RX), P_UART(TX), 0, };
|
|
peripheral_request_list(pins, "bfin-uart");
|
|
return;
|
|
}
|
|
|
|
#if defined(__ADSPBF50x__)
|
|
# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \
|
|
bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | PORT_x_MUX_##mux_tx##_FUNC_1 | PORT_x_MUX_##mux_rx##_FUNC_1); \
|
|
bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
|
|
switch (CONFIG_UART_CONSOLE) {
|
|
case 0: DO_MUX(G, 7, 7, 12, 13); break; /* Port G; mux 7; PG12 and PG13 */
|
|
case 1: DO_MUX(F, 3, 3, 6, 7); break; /* Port F; mux 3; PF6 and PF7 */
|
|
}
|
|
SSYNC();
|
|
#elif defined(__ADSPBF51x__)
|
|
# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \
|
|
bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | PORT_x_MUX_##mux_tx##_FUNC_2 | PORT_x_MUX_##mux_rx##_FUNC_2); \
|
|
bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
|
|
switch (CONFIG_UART_CONSOLE) {
|
|
case 0: DO_MUX(G, 5, 5, 9, 10); break; /* Port G; mux 5; PG9 and PG10 */
|
|
case 1: DO_MUX(F, 2, 3, 14, 15); break; /* Port H; mux 2/3; PH14 and PH15 */
|
|
}
|
|
SSYNC();
|
|
#elif defined(__ADSPBF52x__)
|
|
# define DO_MUX(port, mux, tx, rx) \
|
|
bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~PORT_x_MUX_##mux##_MASK) | PORT_x_MUX_##mux##_FUNC_3); \
|
|
bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
|
|
switch (CONFIG_UART_CONSOLE) {
|
|
case 0: DO_MUX(G, 2, 7, 8); break; /* Port G; mux 2; PG2 and PG8 */
|
|
case 1: DO_MUX(F, 5, 14, 15); break; /* Port F; mux 5; PF14 and PF15 */
|
|
}
|
|
SSYNC();
|
|
#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__)
|
|
const uint16_t func[] = { PFDE, PFTE, };
|
|
bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~func[CONFIG_UART_CONSOLE]);
|
|
bfin_write_PORTF_FER(bfin_read_PORTF_FER() |
|
|
(1 << P_IDENT(P_UART(RX))) |
|
|
(1 << P_IDENT(P_UART(TX))));
|
|
SSYNC();
|
|
#elif defined(__ADSPBF54x__)
|
|
# define DO_MUX(port, tx, rx) \
|
|
bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##tx##_MASK | PORT_x_MUX_##rx##_MASK)) | PORT_x_MUX_##tx##_FUNC_1 | PORT_x_MUX_##rx##_FUNC_1); \
|
|
bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
|
|
switch (CONFIG_UART_CONSOLE) {
|
|
case 0: DO_MUX(E, 7, 8); break; /* Port E; PE7 and PE8 */
|
|
case 1: DO_MUX(H, 0, 1); break; /* Port H; PH0 and PH1 */
|
|
case 2: DO_MUX(B, 4, 5); break; /* Port B; PB4 and PB5 */
|
|
case 3: DO_MUX(B, 6, 7); break; /* Port B; PB6 and PB7 */
|
|
}
|
|
SSYNC();
|
|
#elif defined(__ADSPBF561__)
|
|
/* UART pins could be GPIO, but they aren't pin muxed. */
|
|
#else
|
|
# if (P_UART(RX) & P_DEFINED) || (P_UART(TX) & P_DEFINED)
|
|
# error "missing portmux logic for UART"
|
|
# endif
|
|
#endif
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline int uart_init(uint32_t uart_base)
|
|
{
|
|
/* always enable UART -- avoids anomalies 05000309 and 05000350 */
|
|
bfin_write(&pUART->gctl, UCEN);
|
|
|
|
/* Set LCR to Word Lengh 8-bit word select */
|
|
bfin_write(&pUART->lcr, WLS_8);
|
|
|
|
SSYNC();
|
|
|
|
return 0;
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline int serial_early_init(uint32_t uart_base)
|
|
{
|
|
/* handle portmux crap on different Blackfins */
|
|
serial_do_portmux();
|
|
|
|
return uart_init(uart_base);
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline int serial_early_uninit(uint32_t uart_base)
|
|
{
|
|
/* disable the UART by clearing UCEN */
|
|
bfin_write(&pUART->gctl, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline void serial_early_put_div(uint32_t uart_base, uint16_t divisor)
|
|
{
|
|
/* Set DLAB in LCR to Access DLL and DLH */
|
|
ACCESS_LATCH();
|
|
SSYNC();
|
|
|
|
/* Program the divisor to get the baud rate we want */
|
|
bfin_write(&pUART->dll, LOB(divisor));
|
|
bfin_write(&pUART->dlh, HIB(divisor));
|
|
SSYNC();
|
|
|
|
/* Clear DLAB in LCR to Access THR RBR IER */
|
|
ACCESS_PORT_IER();
|
|
SSYNC();
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline uint16_t serial_early_get_div(void)
|
|
{
|
|
uint32_t uart_base = UART_DLL;
|
|
|
|
/* Set DLAB in LCR to Access DLL and DLH */
|
|
ACCESS_LATCH();
|
|
SSYNC();
|
|
|
|
uint8_t dll = bfin_read(&pUART->dll);
|
|
uint8_t dlh = bfin_read(&pUART->dlh);
|
|
uint16_t divisor = (dlh << 8) | dll;
|
|
|
|
/* Clear DLAB in LCR to Access THR RBR IER */
|
|
ACCESS_PORT_IER();
|
|
SSYNC();
|
|
|
|
return divisor;
|
|
}
|
|
|
|
/* We cannot use get_sclk() early on as it uses caches in external memory */
|
|
#if defined(BFIN_IN_INITCODE) || defined(CONFIG_DEBUG_EARLY_SERIAL)
|
|
# define get_sclk() (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV)
|
|
#endif
|
|
|
|
__attribute__((always_inline))
|
|
static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud)
|
|
{
|
|
/* Translate from baud into divisor in terms of SCLK. The
|
|
* weird multiplication is to make sure we over sample just
|
|
* a little rather than under sample the incoming signals.
|
|
*/
|
|
serial_early_put_div(uart_base,
|
|
(get_sclk() + (baud * 8)) / (baud * 16) - ANOMALY_05000230);
|
|
}
|
|
|
|
#ifndef BFIN_IN_INITCODE
|
|
__attribute__((always_inline))
|
|
static inline void serial_early_puts(const char *s)
|
|
{
|
|
if (BFIN_DEBUG_EARLY_SERIAL) {
|
|
serial_puts("Early: ");
|
|
serial_puts(s);
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#else
|
|
|
|
.macro serial_early_init
|
|
#ifdef CONFIG_DEBUG_EARLY_SERIAL
|
|
call _serial_initialize;
|
|
#endif
|
|
.endm
|
|
|
|
.macro serial_early_set_baud
|
|
#ifdef CONFIG_DEBUG_EARLY_SERIAL
|
|
R0.L = LO(CONFIG_BAUDRATE);
|
|
R0.H = HI(CONFIG_BAUDRATE);
|
|
call _serial_set_baud;
|
|
#endif
|
|
.endm
|
|
|
|
/* Since we embed the string right into our .text section, we need
|
|
* to find its address. We do this by getting our PC and adding 2
|
|
* bytes (which is the length of the jump instruction). Then we
|
|
* pass this address to serial_puts().
|
|
*/
|
|
#ifdef CONFIG_DEBUG_EARLY_SERIAL
|
|
# define serial_early_puts(str) \
|
|
.section .rodata; \
|
|
7: \
|
|
.ascii "Early:"; \
|
|
.ascii __FILE__; \
|
|
.ascii ": "; \
|
|
.ascii str; \
|
|
.asciz "\n"; \
|
|
.previous; \
|
|
R0.L = 7b; \
|
|
R0.H = 7b; \
|
|
call _serial_puts;
|
|
#else
|
|
# define serial_early_puts(str)
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|