mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
134 lines
3.9 KiB
C
134 lines
3.9 KiB
C
/*
|
|
* (C) Copyright 2006
|
|
* KwikByte <kb9200_dev@kwikbyte.com>
|
|
*
|
|
* (C) Copyright 2009
|
|
* Matthias Kaehlcke <matthias@kaehlcke.net>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/AT91RM9200.h>
|
|
#include <asm/arch/hardware.h>
|
|
|
|
#include <nand.h>
|
|
|
|
/*
|
|
* hardware specific access to control-lines
|
|
*/
|
|
|
|
#define MASK_ALE (1 << 22) /* our ALE is A22 */
|
|
#define MASK_CLE (1 << 21) /* our CLE is A21 */
|
|
|
|
#define KB9202_NAND_NCE (1 << 28) /* EN* on D28 */
|
|
#define KB9202_NAND_BUSY (1 << 29) /* RB* on D29 */
|
|
|
|
#define KB9202_SMC2_NWS (1 << 2)
|
|
#define KB9202_SMC2_TDF (1 << 8)
|
|
#define KB9202_SMC2_RWSETUP (1 << 24)
|
|
#define KB9202_SMC2_RWHOLD (1 << 29)
|
|
|
|
/*
|
|
* Board-specific function to access device control signals
|
|
*/
|
|
static void kb9202_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
|
|
{
|
|
struct nand_chip *this = mtd->priv;
|
|
|
|
if (ctrl & NAND_CTRL_CHANGE) {
|
|
ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
|
|
|
|
/* clear ALE and CLE bits */
|
|
IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
|
|
|
|
if (ctrl & NAND_CLE)
|
|
IO_ADDR_W |= MASK_CLE;
|
|
|
|
if (ctrl & NAND_ALE)
|
|
IO_ADDR_W |= MASK_ALE;
|
|
|
|
this->IO_ADDR_W = (void *) IO_ADDR_W;
|
|
|
|
if (ctrl & NAND_NCE)
|
|
writel(KB9202_NAND_NCE, AT91C_PIOC_CODR);
|
|
else
|
|
writel(KB9202_NAND_NCE, AT91C_PIOC_SODR);
|
|
}
|
|
|
|
if (cmd != NAND_CMD_NONE)
|
|
writeb(cmd, this->IO_ADDR_W);
|
|
}
|
|
|
|
|
|
/*
|
|
* Board-specific function to access the device ready signal.
|
|
*/
|
|
static int kb9202_nand_ready(struct mtd_info *mtd)
|
|
{
|
|
return readl(AT91C_PIOC_PDSR) & KB9202_NAND_BUSY;
|
|
}
|
|
|
|
|
|
/*
|
|
* Board-specific NAND init. Copied from include/linux/mtd/nand.h for reference.
|
|
*
|
|
* struct nand_chip - NAND Private Flash Chip Data
|
|
* @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device
|
|
* @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device
|
|
* @hwcontrol: [BOARDSPECIFIC] hardwarespecific function for accesing control-lines
|
|
* @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line
|
|
* If set to NULL no access to ready/busy is available and the ready/busy information
|
|
* is read from the chip status register
|
|
* @enable_hwecc: [BOARDSPECIFIC] function to enable (reset) hardware ecc generator. Must only
|
|
* be provided if a hardware ECC is available
|
|
* @eccmode: [BOARDSPECIFIC] mode of ecc, see defines
|
|
* @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR)
|
|
* @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about
|
|
* special functionality. See the defines for further explanation
|
|
*/
|
|
/*
|
|
* This routine initializes controller and GPIOs.
|
|
*/
|
|
int board_nand_init(struct nand_chip *nand)
|
|
{
|
|
unsigned int value;
|
|
|
|
nand->ecc.mode = NAND_ECC_SOFT;
|
|
nand->cmd_ctrl = kb9202_nand_hwcontrol;
|
|
nand->dev_ready = kb9202_nand_ready;
|
|
|
|
/* in case running outside of bootloader */
|
|
writel(1 << AT91C_ID_PIOC, AT91C_PMC_PCER);
|
|
|
|
/* setup nand flash access (allow ample margin) */
|
|
/* 4 wait states, 1 setup, 1 hold, 1 float for 8-bit device */
|
|
writel(AT91C_SMC2_WSEN | KB9202_SMC2_NWS | KB9202_SMC2_TDF |
|
|
AT91C_SMC2_DBW_8 | KB9202_SMC2_RWSETUP | KB9202_SMC2_RWHOLD,
|
|
AT91C_SMC_CSR3);
|
|
|
|
/* enable internal NAND controller */
|
|
value = readl(AT91C_EBI_CSA);
|
|
value |= AT91C_EBI_CS3A_SMC_SmartMedia;
|
|
writel(value, AT91C_EBI_CSA);
|
|
|
|
/* enable SMOE/SMWE */
|
|
writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_ASR);
|
|
writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_PDR);
|
|
writel(AT91C_PC1_BFRDY_SMOE | AT91C_PC3_BFBAA_SMWE, AT91C_PIOC_OER);
|
|
|
|
/* set NCE to high */
|
|
writel(KB9202_NAND_NCE, AT91C_PIOC_SODR);
|
|
|
|
/* disable output on pin connected to the busy line of the NAND */
|
|
writel(KB9202_NAND_BUSY, AT91C_PIOC_ODR);
|
|
|
|
/* enable the PIO to control NCE and BUSY */
|
|
writel(KB9202_NAND_NCE | KB9202_NAND_BUSY, AT91C_PIOC_PER);
|
|
|
|
/* enable output for NCE */
|
|
writel(KB9202_NAND_NCE, AT91C_PIOC_OER);
|
|
|
|
return (0);
|
|
}
|