u-boot/include/configs/hikey.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

92 lines
2.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2015 Linaro
*
* Peter Griffin <peter.griffin@linaro.org>
*
* Configuration for HiKey 96boards CE. Parts were derived from other ARM
* configurations.
*/
#ifndef __HIKEY_H
#define __HIKEY_H
#include <linux/sizes.h>
#define CONFIG_POWER
#define CONFIG_POWER_HI6553
#define CONFIG_REMAKE_ELF
#define CONFIG_SYS_BOOTM_LEN SZ_64M
/* Physical Memory Map */
/* CONFIG_SYS_TEXT_BASE needs to align with where ATF loads bl33.bin */
#define PHYS_SDRAM_1 0x00000000
/* 1008 MB (the last 16Mb are secured for TrustZone by ATF*/
#define PHYS_SDRAM_1_SIZE 0x3EFFFFFF
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000)
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 19000000
/* Generic Interrupt Controller Definitions */
#define GICD_BASE 0xf6801000
#define GICC_BASE 0xf6802000
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_8M)
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_DWC2_REG_ADDR 0xF72C0000
/*#define CONFIG_DWC2_DFLT_SPEED_FULL*/
#define CONFIG_DWC2_ENABLE_DYNAMIC_FIFO
#endif
#define CONFIG_HIKEY_GPIO
/* Command line configuration */
/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
/* Initial environment variables */
/*
* Defines where the kernel and FDT will be put in RAM
*/
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 1) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_name=Image\0" \
"kernel_addr_r=0x00080000\0" \
"fdtfile=hi6220-hikey.dtb\0" \
"fdt_addr_r=0x02000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
BOOTENV
/* Preserve environment on eMMC */
#define CONFIG_SYS_MMC_ENV_DEV 0 /* Use eMMC */
#define CONFIG_SYS_MMC_ENV_PART 2 /* Use Boot1 partition */
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#endif /* __HIKEY_H */