mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 13:44:29 +00:00
2fcaa84d01
The OP-TEE binary to use is renamed to v2 as the v1 binary has been deprecated and is no longer built by default. Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com>
350 lines
15 KiB
Text
350 lines
15 KiB
Text
Introduction:
|
|
-------------
|
|
The AM65x family of SoCs is the first device family from K3 Multicore
|
|
SoC architecture, targeted for broad market and industrial control with
|
|
aim to meet the complex processing needs of modern embedded products.
|
|
|
|
The device is built over three domains, each containing specific processing
|
|
cores, voltage domains and peripherals:
|
|
1. Wake-up (WKUP) domain:
|
|
- Device Management and Security Controller (DMSC)
|
|
2. Microcontroller (MCU) domain:
|
|
- Dual Core ARM Cortex-R5F processor
|
|
3. MAIN domain:
|
|
- Quad core 64-bit ARM Cortex-A53
|
|
|
|
More info can be found in TRM: http://www.ti.com/lit/pdf/spruid7
|
|
|
|
Boot Flow:
|
|
----------
|
|
On AM65x family devices, ROM supports boot only via MCU(R5). This means that
|
|
bootloader has to run on R5 core. In order to meet this constraint, and for
|
|
the following reasons the boot flow is designed as mentioned:
|
|
1. Need to move away from R5 asap, so that we want to start *any*
|
|
firmware on the r5 cores like.... autosar can be loaded to receive CAN
|
|
response and other safety operations to be started. This operation is
|
|
very time critical and is applicable for all automotive use cases.
|
|
2. U-Boot on A53 should start other remotecores for various
|
|
applications. This should happen before running Linux.
|
|
3. In production boot flow, we might not like to use full u-boot,
|
|
instead use Flacon boot flow to reduce boot time.
|
|
|
|
+------------------------------------------------------------------------+
|
|
| DMSC | R5 | A53 |
|
|
+------------------------------------------------------------------------+
|
|
| +--------+ | | |
|
|
| | Reset | | | |
|
|
| +--------+ | | |
|
|
| : | | |
|
|
| +--------+ | +-----------+ | |
|
|
| | *ROM* |----------|-->| Reset rls | | |
|
|
| +--------+ | +-----------+ | |
|
|
| | | | : | |
|
|
| | ROM | | : | |
|
|
| |services| | : | |
|
|
| | | | +-------------+ | |
|
|
| | | | | *R5 ROM* | | |
|
|
| | | | +-------------+ | |
|
|
| | |<---------|---|Load and auth| | |
|
|
| | | | | tiboot3.bin | | |
|
|
| | | | +-------------+ | |
|
|
| | | | : | |
|
|
| | | | : | |
|
|
| | | | : | |
|
|
| | | | +-------------+ | |
|
|
| | | | | *R5 SPL* | | |
|
|
| | | | +-------------+ | |
|
|
| | | | | Load | | |
|
|
| | | | | sysfw.itb | | |
|
|
| | Start | | +-------------+ | |
|
|
| | System |<---------|---| Start | | |
|
|
| |Firmware| | | SYSFW | | |
|
|
| +--------+ | +-------------+ | |
|
|
| : | | | | |
|
|
| +---------+ | | Load | | |
|
|
| | *SYSFW* | | | system | | |
|
|
| +---------+ | | Config data | | |
|
|
| | |<--------|---| | | |
|
|
| | | | +-------------+ | |
|
|
| | | | | | | |
|
|
| | | | | DDR | | |
|
|
| | | | | config | | |
|
|
| | | | +-------------+ | |
|
|
| | | | | | | |
|
|
| | |<--------|---| Start A53 | | |
|
|
| | | | | and Reset | | |
|
|
| | | | +-------------+ | |
|
|
| | | | | +-----------+ |
|
|
| | |---------|-----------------------|---->| Reset rls | |
|
|
| | | | | +-----------+ |
|
|
| | DMSC | | | : |
|
|
| |Services | | | +-----------+ |
|
|
| | |<--------|-----------------------|---->|*ATF/OPTEE*| |
|
|
| | | | | +-----------+ |
|
|
| | | | | : |
|
|
| | | | | +-----------+ |
|
|
| | |<--------|-----------------------|---->| *A53 SPL* | |
|
|
| | | | | +-----------+ |
|
|
| | | | | | Load | |
|
|
| | | | | | u-boot.img| |
|
|
| | | | | +-----------+ |
|
|
| | | | | : |
|
|
| | | | | +-----------+ |
|
|
| | |<--------|-----------------------|---->| *U-Boot* | |
|
|
| | | | | +-----------+ |
|
|
| | | | | | prompt | |
|
|
| | | | | +-----------+ |
|
|
| +---------+ | | |
|
|
| | | |
|
|
+------------------------------------------------------------------------+
|
|
|
|
- Here DMSC acts as master and provides all the critical services. R5/A53
|
|
requests DMSC to get these services done as shown in the above diagram.
|
|
|
|
Sources:
|
|
--------
|
|
1. SYSFW:
|
|
Tree: git://git.ti.com/k3-image-gen/k3-image-gen.git
|
|
Branch: master
|
|
|
|
2. ATF:
|
|
Tree: https://github.com/ARM-software/arm-trusted-firmware.git
|
|
Branch: master
|
|
|
|
3. OPTEE:
|
|
Tree: https://github.com/OP-TEE/optee_os.git
|
|
Branch: master
|
|
|
|
4. U-Boot:
|
|
Tree: http://git.denx.de/u-boot.git
|
|
Branch: master
|
|
|
|
Build procedure:
|
|
----------------
|
|
1. SYSFW:
|
|
$ make CROSS_COMPILE=arm-linux-gnueabihf-
|
|
|
|
2. ATF:
|
|
$ make CROSS_COMPILE=aarch64-linux-gnu- ARCH=aarch64 PLAT=k3 TARGET_BOARD=generic SPD=opteed
|
|
|
|
3. OPTEE:
|
|
$ make PLATFORM=k3-am65x CFG_ARM64_core=y
|
|
|
|
4. U-Boot:
|
|
|
|
4.1. R5:
|
|
$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- am65x_evm_r5_defconfig O=/tmp/r5
|
|
$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- O=/tmp/r5
|
|
|
|
4.2. A53:
|
|
$ make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- am65x_evm_a53_defconfig O=/tmp/a53
|
|
$ make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- ATF=<path to ATF dir>/build/k3/generic/release/bl31.bin TEE=<path to OPTEE OS dir>/out/arm-plat-k3/core/tee-pager_v2.bin O=/tmp/a53
|
|
|
|
Target Images
|
|
--------------
|
|
Copy the below images to an SD card and boot:
|
|
- sysfw.itb from step 1
|
|
- tiboot3.bin from step 4.1
|
|
- tispl.bin, u-boot.img from 4.2
|
|
|
|
Image formats:
|
|
--------------
|
|
|
|
- tiboot3.bin:
|
|
+-----------------------+
|
|
| X.509 |
|
|
| Certificate |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | R5 | |
|
|
| | u-boot-spl.bin | |
|
|
| | | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | FIT header | |
|
|
| | +---------------+ | |
|
|
| | | | | |
|
|
| | | DTB 1...N | | |
|
|
| | +---------------+ | |
|
|
| +-------------------+ |
|
|
+-----------------------+
|
|
|
|
- tispl.bin
|
|
+-----------------------+
|
|
| |
|
|
| FIT HEADER |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | A53 ATF | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | A53 OPTEE | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | A53 SPL | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | SPL DTB 1...N | |
|
|
| +-------------------+ |
|
|
+-----------------------+
|
|
|
|
- sysfw.itb
|
|
+-----------------------+
|
|
| |
|
|
| FIT HEADER |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | sysfw.bin | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | board config | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | PM config | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | RM config | |
|
|
| +-------------------+ |
|
|
| | | |
|
|
| | Secure config | |
|
|
| +-------------------+ |
|
|
+-----------------------+
|
|
|
|
eMMC:
|
|
-----
|
|
ROM supports booting from eMMC from boot0 partition offset 0x0
|
|
|
|
Flashing images to eMMC:
|
|
|
|
The following commands can be used to download tiboot3.bin, tispl.bin,
|
|
u-boot.img, and sysfw.itb from an SD card and write them to the eMMC boot0
|
|
partition at respective addresses.
|
|
|
|
=> mmc dev 0 1
|
|
=> fatload mmc 1 ${loadaddr} tiboot3.bin
|
|
=> mmc write ${loadaddr} 0x0 0x400
|
|
=> fatload mmc 1 ${loadaddr} tispl.bin
|
|
=> mmc write ${loadaddr} 0x400 0x1000
|
|
=> fatload mmc 1 ${loadaddr} u-boot.img
|
|
=> mmc write ${loadaddr} 0x1400 0x2000
|
|
=> fatload mmc 1 ${loadaddr} sysfw.itb
|
|
=> mmc write ${loadaddr} 0x3600 0x800
|
|
|
|
To give the ROM access to the boot partition, the following commands must be
|
|
used for the first time:
|
|
=> mmc partconf 0 1 1 1
|
|
=> mmc bootbus 0 1 0 0
|
|
|
|
To create a software partition for the rootfs, the following command can be
|
|
used:
|
|
=> gpt write mmc 0 ${partitions}
|
|
|
|
eMMC layout:
|
|
|
|
boot0 partition (8 MB) user partition
|
|
0x0+----------------------------------+ 0x0+-------------------------+
|
|
| tiboot3.bin (512 KB) | | |
|
|
0x400+----------------------------------+ | |
|
|
| tispl.bin (2 MB) | | |
|
|
0x1400+----------------------------------+ | rootfs |
|
|
| u-boot.img (4 MB) | | |
|
|
0x3400+----------------------------------+ | |
|
|
| environment (128 KB) | | |
|
|
0x3500+----------------------------------+ | |
|
|
| backup environment (128 KB) | | |
|
|
0x3600+----------------------------------+ | |
|
|
| sysfw (1 MB) | | |
|
|
0x3E00+----------------------------------+ +-------------------------+
|
|
|
|
Kernel image and DT are expected to be present in the /boot folder of rootfs.
|
|
To boot kernel from eMMC, use the following commands:
|
|
=> setenv mmcdev 0
|
|
=> setenv bootpart 0
|
|
=> boot
|
|
|
|
OSPI:
|
|
-----
|
|
ROM supports booting from OSPI from offset 0x0.
|
|
|
|
Flashing images to OSPI:
|
|
|
|
Below commands can be used to download tiboot3.bin, tispl.bin, u-boot.img,
|
|
and sysfw.itb over tftp and then flash those to OSPI at their respective
|
|
addresses.
|
|
|
|
=> sf probe
|
|
=> tftp ${loadaddr} tiboot3.bin
|
|
=> sf update $loadaddr 0x0 $filesize
|
|
=> tftp ${loadaddr} tispl.bin
|
|
=> sf update $loadaddr 0x80000 $filesize
|
|
=> tftp ${loadaddr} u-boot.img
|
|
=> sf update $loadaddr 0x280000 $filesize
|
|
=> tftp ${loadaddr} sysfw.itb
|
|
=> sf update $loadaddr 0x6C0000 $filesize
|
|
|
|
Flash layout for OSPI:
|
|
|
|
0x0 +----------------------------+
|
|
| ospi.tiboot3(512K) |
|
|
| |
|
|
0x80000 +----------------------------+
|
|
| ospi.tispl(2M) |
|
|
| |
|
|
0x280000 +----------------------------+
|
|
| ospi.u-boot(4M) |
|
|
| |
|
|
0x680000 +----------------------------+
|
|
| ospi.env(128K) |
|
|
| |
|
|
0x6A0000 +----------------------------+
|
|
| ospi.env.backup (128K) |
|
|
| |
|
|
0x6C0000 +----------------------------+
|
|
| ospi.sysfw(1M) |
|
|
| |
|
|
0x7C0000 +----------------------------+
|
|
| padding (256k) |
|
|
0x800000 +----------------------------+
|
|
| ospi.rootfs(UBIFS) |
|
|
| |
|
|
+----------------------------+
|
|
|
|
Kernel Image and DT are expected to be present in the /boot folder of UBIFS
|
|
ospi.rootfs just like in SD card case. U-Boot looks for UBI volume named
|
|
"rootfs" for rootfs.
|
|
|
|
To boot kernel from OSPI, at the U-Boot prompt:
|
|
=> setenv boot ubi
|
|
=> boot
|
|
|
|
UART:
|
|
-----
|
|
ROM supports booting from MCU_UART0 via X-Modem protocol. The entire UART-based
|
|
boot process up to U-Boot (proper) prompt goes through different stages and uses
|
|
different UART peripherals as follows:
|
|
|
|
WHO | Loading WHAT | HW Module | Protocol
|
|
----------+---------------+-------------+------------
|
|
Boot ROM | tiboot3.bin | MCU_UART0 | X-Modem(*)
|
|
R5 SPL | sysfw.itb | MCU_UART0 | Y-Modem(*)
|
|
R5 SPL | tispl.bin | MAIN_UART0 | Y-Modem
|
|
A53 SPL | u-boot.img | MAIN_UART0 | Y-Modem
|
|
|
|
(*) Note that in addition to X/Y-Modem related protocol timeouts the DMSC
|
|
watchdog timeout of 3min (typ.) needs to be observed until System Firmware
|
|
is fully loaded (from sysfw.itb) and started.
|
|
|
|
Example bash script sequence for running on a Linux host PC feeding all boot
|
|
artifacts needed to the device:
|
|
|
|
MCU_DEV=/dev/ttyUSB1
|
|
MAIN_DEV=/dev/ttyUSB0
|
|
|
|
stty -F $MCU_DEV 115200 cs8 -cstopb -parenb
|
|
stty -F $MAIN_DEV 115200 cs8 -cstopb -parenb
|
|
|
|
sb --xmodem tiboot3.bin > $MCU_DEV < $MCU_DEV
|
|
sb --ymodem sysfw.itb > $MCU_DEV < $MCU_DEV
|
|
sb --ymodem tispl.bin > $MAIN_DEV < $MAIN_DEV
|
|
sleep 1
|
|
sb --xmodem u-boot.img > $MAIN_DEV < $MAIN_DEV
|