u-boot/drivers/net/phy/b53.c
Marek Vasut 761e4060fe net: phy: b53: Convert to U_BOOT_PHY_DRIVER()
Convert PHY driver to U_BOOT_PHY_DRIVER() macro and drop phy_register() init call.

Converted using sed
"s@^static struct phy_driver \(.*\)_driver = \+{@U_BOOT_PHY_DRIVER(\L\1) = {"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
2023-04-07 14:18:48 +02:00

763 lines
18 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017
* Broadcom
* Florian Fainelli <f.fainelli@gmail.com>
*/
/*
* PHY driver for Broadcom BCM53xx (roboswitch) Ethernet switches.
*
* This driver configures the b53 for basic use as a PHY. The switch supports
* vendor tags and VLAN configuration that can affect the switching decisions.
* This driver uses a simple configuration in which all ports are only allowed
* to send frames to the CPU port and receive frames from the CPU port this
* providing port isolation (no cross talk).
*
* The configuration determines which PHY ports to activate using the
* CONFIG_B53_PHY_PORTS bitmask. Set bit N will active port N and so on.
*
* This driver was written primarily for the Lamobo R1 platform using a BCM53152
* switch but the BCM53xx being largely register compatible, extending it to
* cover other switches would be trivial.
*/
#include <common.h>
#include <command.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <errno.h>
#include <malloc.h>
#include <miiphy.h>
#include <netdev.h>
/* Pseudo-PHY address (non configurable) to access internal registers */
#define BRCM_PSEUDO_PHY_ADDR 30
/* Maximum number of ports possible */
#define B53_N_PORTS 9
#define B53_CTRL_PAGE 0x00 /* Control */
#define B53_MGMT_PAGE 0x02 /* Management Mode */
/* Port VLAN Page */
#define B53_PVLAN_PAGE 0x31
/* Control Page registers */
#define B53_PORT_CTRL(i) (0x00 + (i))
#define PORT_CTRL_RX_DISABLE BIT(0)
#define PORT_CTRL_TX_DISABLE BIT(1)
#define PORT_CTRL_RX_BCST_EN BIT(2) /* Broadcast RX (P8 only) */
#define PORT_CTRL_RX_MCST_EN BIT(3) /* Multicast RX (P8 only) */
#define PORT_CTRL_RX_UCST_EN BIT(4) /* Unicast RX (P8 only) */
/* Switch Mode Control Register (8 bit) */
#define B53_SWITCH_MODE 0x0b
#define SM_SW_FWD_MODE BIT(0) /* 1 = Managed Mode */
#define SM_SW_FWD_EN BIT(1) /* Forwarding Enable */
/* IMP Port state override register (8 bit) */
#define B53_PORT_OVERRIDE_CTRL 0x0e
#define PORT_OVERRIDE_LINK BIT(0)
#define PORT_OVERRIDE_FULL_DUPLEX BIT(1) /* 0 = Half Duplex */
#define PORT_OVERRIDE_SPEED_S 2
#define PORT_OVERRIDE_SPEED_10M (0 << PORT_OVERRIDE_SPEED_S)
#define PORT_OVERRIDE_SPEED_100M (1 << PORT_OVERRIDE_SPEED_S)
#define PORT_OVERRIDE_SPEED_1000M (2 << PORT_OVERRIDE_SPEED_S)
/* BCM5325 only */
#define PORT_OVERRIDE_RV_MII_25 BIT(4)
#define PORT_OVERRIDE_RX_FLOW BIT(4)
#define PORT_OVERRIDE_TX_FLOW BIT(5)
/* BCM5301X only, requires setting 1000M */
#define PORT_OVERRIDE_SPEED_2000M BIT(6)
#define PORT_OVERRIDE_EN BIT(7) /* Use the register contents */
#define B53_RGMII_CTRL_IMP 0x60
#define RGMII_CTRL_ENABLE_GMII BIT(7)
#define RGMII_CTRL_TIMING_SEL BIT(2)
#define RGMII_CTRL_DLL_RXC BIT(1)
#define RGMII_CTRL_DLL_TXC BIT(0)
/* Switch control (8 bit) */
#define B53_SWITCH_CTRL 0x22
#define B53_MII_DUMB_FWDG_EN BIT(6)
/* Software reset register (8 bit) */
#define B53_SOFTRESET 0x79
#define SW_RST BIT(7)
#define EN_CH_RST BIT(6)
#define EN_SW_RST BIT(4)
/* Fast Aging Control register (8 bit) */
#define B53_FAST_AGE_CTRL 0x88
#define FAST_AGE_STATIC BIT(0)
#define FAST_AGE_DYNAMIC BIT(1)
#define FAST_AGE_PORT BIT(2)
#define FAST_AGE_VLAN BIT(3)
#define FAST_AGE_STP BIT(4)
#define FAST_AGE_MC BIT(5)
#define FAST_AGE_DONE BIT(7)
/* Port VLAN mask (16 bit) IMP port is always 8, also on 5325 & co */
#define B53_PVLAN_PORT_MASK(i) ((i) * 2)
/* MII registers */
#define REG_MII_PAGE 0x10 /* MII Page register */
#define REG_MII_ADDR 0x11 /* MII Address register */
#define REG_MII_DATA0 0x18 /* MII Data register 0 */
#define REG_MII_DATA1 0x19 /* MII Data register 1 */
#define REG_MII_DATA2 0x1a /* MII Data register 2 */
#define REG_MII_DATA3 0x1b /* MII Data register 3 */
#define REG_MII_PAGE_ENABLE BIT(0)
#define REG_MII_ADDR_WRITE BIT(0)
#define REG_MII_ADDR_READ BIT(1)
struct b53_device {
struct mii_dev *bus;
unsigned int cpu_port;
};
static int b53_mdio_op(struct mii_dev *bus, u8 page, u8 reg, u16 op)
{
int ret;
int i;
u16 v;
/* set page number */
v = (page << 8) | REG_MII_PAGE_ENABLE;
ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_PAGE, v);
if (ret)
return ret;
/* set register address */
v = (reg << 8) | op;
ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_ADDR, v);
if (ret)
return ret;
/* check if operation completed */
for (i = 0; i < 5; ++i) {
v = bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_ADDR);
if (!(v & (REG_MII_ADDR_WRITE | REG_MII_ADDR_READ)))
break;
udelay(100);
}
if (i == 5)
return -EIO;
return 0;
}
static int b53_mdio_read8(struct mii_dev *bus, u8 page, u8 reg, u8 *val)
{
int ret;
ret = b53_mdio_op(bus, page, reg, REG_MII_ADDR_READ);
if (ret)
return ret;
*val = bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0) & 0xff;
return 0;
}
static int b53_mdio_read16(struct mii_dev *bus, u8 page, u8 reg, u16 *val)
{
int ret;
ret = b53_mdio_op(bus, page, reg, REG_MII_ADDR_READ);
if (ret)
return ret;
*val = bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0);
return 0;
}
static int b53_mdio_read32(struct mii_dev *bus, u8 page, u8 reg, u32 *val)
{
int ret;
ret = b53_mdio_op(bus, page, reg, REG_MII_ADDR_READ);
if (ret)
return ret;
*val = bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0);
*val |= bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA1) << 16;
return 0;
}
static int b53_mdio_read48(struct mii_dev *bus, u8 page, u8 reg, u64 *val)
{
u64 temp = 0;
int i;
int ret;
ret = b53_mdio_op(bus, page, reg, REG_MII_ADDR_READ);
if (ret)
return ret;
for (i = 2; i >= 0; i--) {
temp <<= 16;
temp |= bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0 + i);
}
*val = temp;
return 0;
}
static int b53_mdio_read64(struct mii_dev *bus, u8 page, u8 reg, u64 *val)
{
u64 temp = 0;
int i;
int ret;
ret = b53_mdio_op(bus, page, reg, REG_MII_ADDR_READ);
if (ret)
return ret;
for (i = 3; i >= 0; i--) {
temp <<= 16;
temp |= bus->read(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0 + i);
}
*val = temp;
return 0;
}
static int b53_mdio_write8(struct mii_dev *bus, u8 page, u8 reg, u8 value)
{
int ret;
ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0, value);
if (ret)
return ret;
return b53_mdio_op(bus, page, reg, REG_MII_ADDR_WRITE);
}
static int b53_mdio_write16(struct mii_dev *bus, u8 page, u8 reg,
u16 value)
{
int ret;
ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR, MDIO_DEVAD_NONE,
REG_MII_DATA0, value);
if (ret)
return ret;
return b53_mdio_op(bus, page, reg, REG_MII_ADDR_WRITE);
}
static int b53_mdio_write32(struct mii_dev *bus, u8 page, u8 reg,
u32 value)
{
unsigned int i;
u32 temp = value;
for (i = 0; i < 2; i++) {
int ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR,
MDIO_DEVAD_NONE,
REG_MII_DATA0 + i, temp & 0xffff);
if (ret)
return ret;
temp >>= 16;
}
return b53_mdio_op(bus, page, reg, REG_MII_ADDR_WRITE);
}
static int b53_mdio_write48(struct mii_dev *bus, u8 page, u8 reg,
u64 value)
{
unsigned int i;
u64 temp = value;
for (i = 0; i < 3; i++) {
int ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR,
MDIO_DEVAD_NONE,
REG_MII_DATA0 + i, temp & 0xffff);
if (ret)
return ret;
temp >>= 16;
}
return b53_mdio_op(bus, page, reg, REG_MII_ADDR_WRITE);
}
static int b53_mdio_write64(struct mii_dev *bus, u8 page, u8 reg,
u64 value)
{
unsigned int i;
u64 temp = value;
for (i = 0; i < 4; i++) {
int ret = bus->write(bus, BRCM_PSEUDO_PHY_ADDR,
MDIO_DEVAD_NONE,
REG_MII_DATA0 + i, temp & 0xffff);
if (ret)
return ret;
temp >>= 16;
}
return b53_mdio_op(bus, page, reg, REG_MII_ADDR_WRITE);
}
static inline int b53_read8(struct b53_device *dev, u8 page,
u8 reg, u8 *value)
{
return b53_mdio_read8(dev->bus, page, reg, value);
}
static inline int b53_read16(struct b53_device *dev, u8 page,
u8 reg, u16 *value)
{
return b53_mdio_read16(dev->bus, page, reg, value);
}
static inline int b53_read32(struct b53_device *dev, u8 page,
u8 reg, u32 *value)
{
return b53_mdio_read32(dev->bus, page, reg, value);
}
static inline int b53_read48(struct b53_device *dev, u8 page,
u8 reg, u64 *value)
{
return b53_mdio_read48(dev->bus, page, reg, value);
}
static inline int b53_read64(struct b53_device *dev, u8 page,
u8 reg, u64 *value)
{
return b53_mdio_read64(dev->bus, page, reg, value);
}
static inline int b53_write8(struct b53_device *dev, u8 page,
u8 reg, u8 value)
{
return b53_mdio_write8(dev->bus, page, reg, value);
}
static inline int b53_write16(struct b53_device *dev, u8 page,
u8 reg, u16 value)
{
return b53_mdio_write16(dev->bus, page, reg, value);
}
static inline int b53_write32(struct b53_device *dev, u8 page,
u8 reg, u32 value)
{
return b53_mdio_write32(dev->bus, page, reg, value);
}
static inline int b53_write48(struct b53_device *dev, u8 page,
u8 reg, u64 value)
{
return b53_mdio_write48(dev->bus, page, reg, value);
}
static inline int b53_write64(struct b53_device *dev, u8 page,
u8 reg, u64 value)
{
return b53_mdio_write64(dev->bus, page, reg, value);
}
static int b53_flush_arl(struct b53_device *dev, u8 mask)
{
unsigned int i;
b53_write8(dev, B53_CTRL_PAGE, B53_FAST_AGE_CTRL,
FAST_AGE_DONE | FAST_AGE_DYNAMIC | mask);
for (i = 0; i < 10; i++) {
u8 fast_age_ctrl;
b53_read8(dev, B53_CTRL_PAGE, B53_FAST_AGE_CTRL,
&fast_age_ctrl);
if (!(fast_age_ctrl & FAST_AGE_DONE))
goto out;
mdelay(1);
}
return -ETIMEDOUT;
out:
/* Only age dynamic entries (default behavior) */
b53_write8(dev, B53_CTRL_PAGE, B53_FAST_AGE_CTRL, FAST_AGE_DYNAMIC);
return 0;
}
static int b53_switch_reset(struct phy_device *phydev)
{
struct b53_device *dev = phydev->priv;
unsigned int timeout = 1000;
u8 mgmt;
u8 reg;
b53_read8(dev, B53_CTRL_PAGE, B53_SOFTRESET, &reg);
reg |= SW_RST | EN_SW_RST | EN_CH_RST;
b53_write8(dev, B53_CTRL_PAGE, B53_SOFTRESET, reg);
do {
b53_read8(dev, B53_CTRL_PAGE, B53_SOFTRESET, &reg);
if (!(reg & SW_RST))
break;
mdelay(1);
} while (timeout-- > 0);
if (timeout == 0)
return -ETIMEDOUT;
b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, &mgmt);
if (!(mgmt & SM_SW_FWD_EN)) {
mgmt &= ~SM_SW_FWD_MODE;
mgmt |= SM_SW_FWD_EN;
b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, mgmt);
b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_MODE, &mgmt);
if (!(mgmt & SM_SW_FWD_EN)) {
printf("Failed to enable switch!\n");
return -EINVAL;
}
}
/* Include IMP port in dumb forwarding mode when no tagging protocol
* is configured
*/
b53_read8(dev, B53_CTRL_PAGE, B53_SWITCH_CTRL, &mgmt);
mgmt |= B53_MII_DUMB_FWDG_EN;
b53_write8(dev, B53_CTRL_PAGE, B53_SWITCH_CTRL, mgmt);
return b53_flush_arl(dev, FAST_AGE_STATIC);
}
static void b53_enable_cpu_port(struct phy_device *phydev)
{
struct b53_device *dev = phydev->priv;
u8 port_ctrl;
port_ctrl = PORT_CTRL_RX_BCST_EN |
PORT_CTRL_RX_MCST_EN |
PORT_CTRL_RX_UCST_EN;
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(dev->cpu_port), port_ctrl);
port_ctrl = PORT_OVERRIDE_EN | PORT_OVERRIDE_LINK |
PORT_OVERRIDE_FULL_DUPLEX | PORT_OVERRIDE_SPEED_1000M;
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_OVERRIDE_CTRL, port_ctrl);
b53_read8(dev, B53_CTRL_PAGE, B53_RGMII_CTRL_IMP, &port_ctrl);
}
static void b53_imp_vlan_setup(struct b53_device *dev, int cpu_port)
{
unsigned int port;
u16 pvlan;
/* Enable the IMP port to be in the same VLAN as the other ports
* on a per-port basis such that we only have Port i and IMP in
* the same VLAN.
*/
for (port = 0; port < B53_N_PORTS; port++) {
if (!((1 << port) & CONFIG_B53_PHY_PORTS))
continue;
b53_read16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port),
&pvlan);
pvlan |= BIT(cpu_port);
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port),
pvlan);
}
}
static int b53_port_enable(struct phy_device *phydev, unsigned int port)
{
struct b53_device *dev = phydev->priv;
unsigned int cpu_port = dev->cpu_port;
u16 pvlan;
/* Clear the Rx and Tx disable bits and set to no spanning tree */
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), 0);
/* Set this port, and only this one to be in the default VLAN */
b53_read16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), &pvlan);
pvlan &= ~0x1ff;
pvlan |= BIT(port);
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
b53_imp_vlan_setup(dev, cpu_port);
return 0;
}
static int b53_switch_init(struct phy_device *phydev)
{
static int init;
int ret;
if (init)
return 0;
ret = b53_switch_reset(phydev);
if (ret < 0)
return ret;
b53_enable_cpu_port(phydev);
init = 1;
return 0;
}
static int b53_probe(struct phy_device *phydev)
{
struct b53_device *dev;
int ret;
dev = malloc(sizeof(*dev));
if (!dev)
return -ENOMEM;
memset(dev, 0, sizeof(*dev));
phydev->priv = dev;
dev->bus = phydev->bus;
dev->cpu_port = CONFIG_B53_CPU_PORT;
ret = b53_switch_reset(phydev);
if (ret < 0)
return ret;
return 0;
}
static int b53_phy_config(struct phy_device *phydev)
{
unsigned int port;
int res;
res = b53_switch_init(phydev);
if (res < 0)
return res;
for (port = 0; port < B53_N_PORTS; port++) {
if (!((1 << port) & CONFIG_B53_PHY_PORTS))
continue;
res = b53_port_enable(phydev, port);
if (res < 0) {
printf("Error enabling port %i\n", port);
continue;
}
res = genphy_config_aneg(phydev);
if (res < 0) {
printf("Error setting PHY %i autoneg\n", port);
continue;
}
res = 0;
}
return res;
}
static int b53_phy_startup(struct phy_device *phydev)
{
unsigned int port;
int res;
for (port = 0; port < B53_N_PORTS; port++) {
if (!((1 << port) & CONFIG_B53_PHY_PORTS))
continue;
phydev->addr = port;
res = genphy_startup(phydev);
if (res < 0)
continue;
else
break;
}
/* Since we are connected directly to the switch, hardcode the link
* parameters to match those of the CPU port configured in
* b53_enable_cpu_port, we cannot be dependent on the user-facing port
* settings (e.g: 100Mbits/sec would not work here)
*/
phydev->speed = 1000;
phydev->duplex = 1;
phydev->link = 1;
return 0;
}
U_BOOT_PHY_DRIVER(b53) = {
.name = "Broadcom BCM53125",
.uid = 0x03625c00,
.mask = 0xfffffc00,
.features = PHY_GBIT_FEATURES,
.probe = b53_probe,
.config = b53_phy_config,
.startup = b53_phy_startup,
.shutdown = &genphy_shutdown,
};
int do_b53_reg_read(const char *name, int argc, char *const argv[])
{
u8 page, offset, width;
struct mii_dev *bus;
int ret = -EINVAL;
u64 value64 = 0;
u32 value32 = 0;
u16 value16 = 0;
u8 value8 = 0;
bus = miiphy_get_dev_by_name(name);
if (!bus) {
printf("unable to find MDIO bus: %s\n", name);
return ret;
}
page = hextoul(argv[1], NULL);
offset = hextoul(argv[2], NULL);
width = dectoul(argv[3], NULL);
switch (width) {
case 8:
ret = b53_mdio_read8(bus, page, offset, &value8);
printf("page=0x%02x, offset=0x%02x, value=0x%02x\n",
page, offset, value8);
break;
case 16:
ret = b53_mdio_read16(bus, page, offset, &value16);
printf("page=0x%02x, offset=0x%02x, value=0x%04x\n",
page, offset, value16);
break;
case 32:
ret = b53_mdio_read32(bus, page, offset, &value32);
printf("page=0x%02x, offset=0x%02x, value=0x%08x\n",
page, offset, value32);
break;
case 48:
ret = b53_mdio_read48(bus, page, offset, &value64);
printf("page=0x%02x, offset=0x%02x, value=0x%012llx\n",
page, offset, value64);
break;
case 64:
ret = b53_mdio_read48(bus, page, offset, &value64);
printf("page=0x%02x, offset=0x%02x, value=0x%016llx\n",
page, offset, value64);
break;
default:
printf("Unsupported width: %d\n", width);
break;
}
return ret;
}
int do_b53_reg_write(const char *name, int argc, char *const argv[])
{
u8 page, offset, width;
struct mii_dev *bus;
int ret = -EINVAL;
u64 value64 = 0;
u32 value = 0;
bus = miiphy_get_dev_by_name(name);
if (!bus) {
printf("unable to find MDIO bus: %s\n", name);
return ret;
}
page = hextoul(argv[1], NULL);
offset = hextoul(argv[2], NULL);
width = dectoul(argv[3], NULL);
if (width == 48 || width == 64)
value64 = simple_strtoull(argv[4], NULL, 16);
else
value = hextoul(argv[4], NULL);
switch (width) {
case 8:
ret = b53_mdio_write8(bus, page, offset, value & 0xff);
break;
case 16:
ret = b53_mdio_write16(bus, page, offset, value);
break;
case 32:
ret = b53_mdio_write32(bus, page, offset, value);
break;
case 48:
ret = b53_mdio_write48(bus, page, offset, value64);
break;
case 64:
ret = b53_mdio_write64(bus, page, offset, value64);
break;
default:
printf("Unsupported width: %d\n", width);
break;
}
return ret;
}
int do_b53_reg(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
{
const char *cmd, *mdioname;
int ret = 0;
if (argc < 2)
return cmd_usage(cmdtp);
cmd = argv[1];
--argc;
++argv;
if (!strcmp(cmd, "write")) {
if (argc < 4)
return cmd_usage(cmdtp);
mdioname = argv[1];
--argc;
++argv;
ret = do_b53_reg_write(mdioname, argc, argv);
} else if (!strcmp(cmd, "read")) {
if (argc < 5)
return cmd_usage(cmdtp);
mdioname = argv[1];
--argc;
++argv;
ret = do_b53_reg_read(mdioname, argc, argv);
} else {
return cmd_usage(cmdtp);
}
return ret;
}
U_BOOT_CMD(b53_reg, 7, 1, do_b53_reg,
"Broadcom B53 switch register access",
"write mdioname page (hex) offset (hex) width (dec) value (hex)\n"
"read mdioname page (hex) offset (hex) width (dec)\n"
);