Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-11 22:03:15 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/esd/meesc/meesc.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style 
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

276 lines
6.5 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* (C) Copyright 2009-2015
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*/
#include <common.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/at91_matrix.h>
#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_REVISION_TAG
static int hw_rev = -1; /* hardware revision */
int get_hw_rev(void)
{
if (hw_rev >= 0)
return hw_rev;
hw_rev = at91_get_pio_value(AT91_PIO_PORTB, 19);
hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 20) << 1;
hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 21) << 2;
hw_rev |= at91_get_pio_value(AT91_PIO_PORTB, 22) << 3;
if (hw_rev == 15)
hw_rev = 0;
return hw_rev;
}
#endif /* CONFIG_REVISION_TAG */
#ifdef CONFIG_CMD_NAND
static void meesc_nand_hw_init(void)
{
unsigned long csa;
at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
/* Enable CS3 */
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
writel(csa, &matrix->csa[0]);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(2),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(6) | AT91_SMC_CYCLE_NRD(6),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(12),
&smc->cs[3].mode);
/* Configure RDY/BSY */
gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
/* Enable NandFlash */
gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif /* CONFIG_CMD_NAND */
#ifdef CONFIG_MACB
static void meesc_macb_hw_init(void)
{
at91_periph_clk_enable(ATMEL_ID_EMAC);
at91_macb_hw_init();
}
#endif
/*
* Static memory controller initialization to enable Beckhoff ET1100 EtherCAT
* controller debugging
* The ET1100 is located at physical address 0x70000000
* Its process memory is located at physical address 0x70001000
*/
static void meesc_ethercat_hw_init(void)
{
at91_smc_t *smc1 = (at91_smc_t *) ATMEL_BASE_SMC1;
/* Configure SMC EBI1_CS0 for EtherCAT */
writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(0) | AT91_SMC_SETUP_NCS_RD(0),
&smc1->cs[0].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(9) |
AT91_SMC_PULSE_NRD(5) | AT91_SMC_PULSE_NCS_RD(9),
&smc1->cs[0].pulse);
writel(AT91_SMC_CYCLE_NWE(10) | AT91_SMC_CYCLE_NRD(6),
&smc1->cs[0].cycle);
/*
* Configure behavior at external wait signal, byte-select mode, 16 bit
* data bus width, none data float wait states and TDF optimization
*/
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_EXNW_READY |
AT91_SMC_MODE_DBW_16 | AT91_SMC_MODE_TDF_CYCLE(0) |
AT91_SMC_MODE_TDF, &smc1->cs[0].mode);
/* Configure RDY/BSY */
at91_set_b_periph(AT91_PIO_PORTE, 20, 0); /* EBI1_NWAIT */
}
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
PHYS_SDRAM_SIZE);
return 0;
}
int dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM;
gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
#endif
return rc;
}
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
char str[32];
u_char hw_type; /* hardware type */
/* read the "Type" register of the ET1100 controller */
hw_type = readb(CONFIG_ET1100_BASE);
switch (hw_type) {
case 0x11:
case 0x3F:
/* ET1100 present, arch number of MEESC-Board */
gd->bd->bi_arch_number = MACH_TYPE_MEESC;
puts("Board: CAN-EtherCAT Gateway");
break;
case 0xFF:
/* no ET1100 present, arch number of EtherCAN/2-Board */
gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
puts("Board: EtherCAN/2 Gateway");
/* switch on LED1D */
at91_set_pio_output(AT91_PIO_PORTB, 12, 1);
break;
default:
/* assume, no ET1100 present, arch number of EtherCAN/2-Board */
gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
printf("ERROR! Read invalid hw_type: %02X\n", hw_type);
puts("Board: EtherCAN/2 Gateway");
break;
}
if (env_get_f("serial#", str, sizeof(str)) > 0) {
puts(", serial# ");
puts(str);
}
#ifdef CONFIG_REVISION_TAG
printf("\nHardware-revision: 1.%d\n", get_hw_rev());
#endif
printf("Mach-type: %lu\n", gd->bd->bi_arch_number);
return 0;
}
#endif /* CONFIG_DISPLAY_BOARDINFO */
#ifdef CONFIG_SERIAL_TAG
void get_board_serial(struct tag_serialnr *serialnr)
{
char *str;
char *serial = env_get("serial#");
if (serial) {
str = strchr(serial, '_');
if (str && (strlen(str) >= 4)) {
serialnr->high = (*(str + 1) << 8) | *(str + 2);
serialnr->low = simple_strtoul(str + 3, NULL, 16);
}
} else {
serialnr->high = 0;
serialnr->low = 0;
}
}
#endif
#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return hw_rev | 0x100;
}
#endif
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
char *str;
char buf[32];
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
/*
* Normally the processor clock has a divisor of 2.
* In some cases this this needs to be set to 4.
* Check the user has set environment mdiv to 4 to change the divisor.
*/
str = env_get("mdiv");
if (str && (strcmp(str, "4") == 0)) {
writel((readl(&pmc->mckr) & ~AT91_PMC_MDIV) |
AT91SAM9_PMC_MDIV_4, &pmc->mckr);
at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
serial_setbrg();
/* Notify the user that the clock is not default */
printf("Setting master clock to %s MHz\n",
strmhz(buf, get_mck_clk_rate()));
}
return 0;
}
#endif /* CONFIG_MISC_INIT_R */
int board_early_init_f(void)
{
at91_periph_clk_enable(ATMEL_ID_UHP);
return 0;
}
int board_init(void)
{
/* initialize ET1100 Controller */
meesc_ethercat_hw_init();
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
meesc_nand_hw_init();
#endif
#ifdef CONFIG_MACB
meesc_macb_hw_init();
#endif
#ifdef CONFIG_AT91_CAN
at91_can_hw_init();
#endif
#ifdef CONFIG_USB_OHCI_NEW
at91_uhp_hw_init();
#endif
return 0;
}
Reference in a new issue View git blame Copy permalink