mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-22 11:13:07 +00:00
b62450cf22
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
102 lines
2.7 KiB
C
102 lines
2.7 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright 2019 Google LLC
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <log.h>
|
|
#include <asm/cpu_common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/msr.h>
|
|
#include <asm/pci.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/iomap.h>
|
|
#include <asm/arch/uart.h>
|
|
#include <power/acpi_pmc.h>
|
|
|
|
/* Define this here to avoid referencing any drivers for the debug UART 1 */
|
|
#define PCH_DEV_P2SB PCI_BDF(0, 0x0d, 0)
|
|
|
|
void cpu_flush_l1d_to_l2(void)
|
|
{
|
|
struct msr_t msr;
|
|
|
|
msr = msr_read(MSR_POWER_MISC);
|
|
msr.lo |= FLUSH_DL1_L2;
|
|
msr_write(MSR_POWER_MISC, msr);
|
|
}
|
|
|
|
void enable_pm_timer_emulation(const struct udevice *pmc)
|
|
{
|
|
struct acpi_pmc_upriv *upriv = dev_get_uclass_priv(pmc);
|
|
msr_t msr;
|
|
|
|
/*
|
|
* The derived frequency is calculated as follows:
|
|
* (CTC_FREQ * msr[63:32]) >> 32 = target frequency.
|
|
*
|
|
* Back-solve the multiplier so the 3.579545MHz ACPI timer frequency is
|
|
* used.
|
|
*/
|
|
msr.hi = (3579545ULL << 32) / CTC_FREQ;
|
|
|
|
/* Set PM1 timer IO port and enable */
|
|
msr.lo = EMULATE_PM_TMR_EN | (upriv->acpi_base + R_ACPI_PM1_TMR);
|
|
debug("PM timer %x %x\n", msr.hi, msr.lo);
|
|
msr_write(MSR_EMULATE_PM_TIMER, msr);
|
|
}
|
|
|
|
static void pch_uart_init(void)
|
|
{
|
|
/*
|
|
* Set up the pinmux so that the UART rx/tx signals are connected
|
|
* outside the SoC.
|
|
*
|
|
* There are about 500 lines of code required to program the GPIO
|
|
* configuration for the UARTs. But it boils down to four writes, and
|
|
* for the debug UART we want the minimum possible amount of code before
|
|
* the UART is running. So just add the magic writes here. See
|
|
* apl_hostbridge_early_init_pinctrl() for the full horror.
|
|
*/
|
|
if (PCI_FUNC(PCH_DEV_UART) == 1) {
|
|
writel(0x40000402, 0xd0c50650);
|
|
writel(0x3c47, 0xd0c50654);
|
|
writel(0x40000400, 0xd0c50658);
|
|
writel(0x3c48, 0xd0c5065c);
|
|
} else { /* UART2 */
|
|
writel(0x40000402, 0xd0c50670);
|
|
writel(0x3c4b, 0xd0c50674);
|
|
writel(0x40000400, 0xd0c50678);
|
|
writel(0x3c4c, 0xd0c5067c);
|
|
}
|
|
|
|
#ifdef CONFIG_DEBUG_UART
|
|
apl_uart_init(PCH_DEV_UART, CONFIG_VAL(DEBUG_UART_BASE));
|
|
#endif
|
|
}
|
|
|
|
static void p2sb_enable_bar(ulong bar)
|
|
{
|
|
/* Enable PCR Base address in PCH */
|
|
pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_0, bar,
|
|
PCI_SIZE_32);
|
|
pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_1, 0, PCI_SIZE_32);
|
|
|
|
/* Enable P2SB MSE */
|
|
pci_x86_write_config(PCH_DEV_P2SB, PCI_COMMAND,
|
|
PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY,
|
|
PCI_SIZE_8);
|
|
}
|
|
|
|
/*
|
|
* board_debug_uart_init() - Init the debug UART ready for use
|
|
*
|
|
* This is the minimum init needed to get the UART running. It avoids any
|
|
* drivers or complex code, so that the UART is running as soon as possible.
|
|
*/
|
|
void board_debug_uart_init(void)
|
|
{
|
|
p2sb_enable_bar(IOMAP_P2SB_BAR);
|
|
pch_uart_init();
|
|
}
|