Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-28 07:31:15 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/sks-kinkel/sksimx6/sksimx6.c
Yangbo Lu e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms 
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00

425 lines
11 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2016 Stefano Babic <sbabic@denx.de>
*/
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/video.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <spl.h>
#include <netdev.h>
#include <miiphy.h>
#include <micrel.h>
#include <common.h>
#include <malloc.h>
#include <fuse.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
static iomux_v3_cfg_t const uart1_pads[] = {
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const gpios_pads[] = {
IOMUX_PADS(PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),/* CD */
};
static iomux_v3_cfg_t const enet_pads[] = {
IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |
MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
iomux_v3_cfg_t const enet_pads1[] = {
/* pin 35 - 1 (PHY_AD2) on reset */
IOMUX_PADS(PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* pin 32 - 1 - (MODE0) all */
IOMUX_PADS(PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* pin 31 - 1 - (MODE1) all */
IOMUX_PADS(PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* pin 28 - 1 - (MODE2) all */
IOMUX_PADS(PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* pin 27 - 1 - (MODE3) all */
IOMUX_PADS(PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
IOMUX_PADS(PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* pin 42 PHY nRST */
IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static int mx6_rgmii_rework(struct phy_device *phydev)
{
/* min rx data delay */
ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
0x0);
/* min tx data delay */
ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
0x0);
/* max rx/tx clock delay, min rx/tx control */
ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
0xf0f0);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
mx6_rgmii_rework(phydev);
if (phydev->drv->config)
return phydev->drv->config(phydev);
return 0;
}
#define ENET_NRST IMX_GPIO_NR(1, 25)
void setup_iomux_enet(void)
{
SETUP_IOMUX_PADS(enet_pads);
}
int board_eth_init(bd_t *bis)
{
uint32_t base = IMX_FEC_BASE;
struct mii_dev *bus = NULL;
struct phy_device *phydev = NULL;
int ret;
setup_iomux_enet();
bus = fec_get_miibus(base, -1);
if (!bus)
return -EINVAL;
/* scan phy */
phydev = phy_find_by_mask(bus, (0xf << CONFIG_FEC_MXC_PHYADDR),
PHY_INTERFACE_MODE_RGMII);
if (!phydev) {
ret = -EINVAL;
goto free_bus;
}
ret = fec_probe(bis, -1, base, bus, phydev);
if (ret)
goto free_phydev;
return 0;
free_phydev:
free(phydev);
free_bus:
free(bus);
return ret;
}
int board_early_init_f(void)
{
SETUP_IOMUX_PADS(uart1_pads);
return 0;
}
int board_init(void)
{
/* Address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
/* Take in reset the ATMega processor */
SETUP_IOMUX_PADS(gpios_pads);
gpio_direction_output(IMX_GPIO_NR(5, 4), 0);
return 0;
}
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
struct fsl_esdhc_cfg usdhc_cfg[1] = {
{USDHC2_BASE_ADDR, 0},
};
#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 0)
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret = 0;
if (cfg->esdhc_base == USDHC2_BASE_ADDR)
ret = 1;
return ret;
}
int board_mmc_init(bd_t *bis)
{
int ret;
SETUP_IOMUX_PADS(usdhc2_pads);
gpio_direction_input(USDHC2_CD_GPIO);
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
usdhc_cfg[0].max_bus_width = 4;
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
if (ret) {
printf("Warning: failed to initialize mmc dev \n");
return ret;
}
return 0;
}
#if defined(CONFIG_SPL_BUILD)
#include <asm/arch/mx6-ddr.h>
/*
* Driving strength:
* 0x30 == 40 Ohm
* 0x28 == 48 Ohm
*/
#define IMX6SDL_DRIVE_STRENGTH 0x230
/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
.dram_sdclk_0 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdclk_1 = IMX6SDL_DRIVE_STRENGTH,
.dram_cas = IMX6SDL_DRIVE_STRENGTH,
.dram_ras = IMX6SDL_DRIVE_STRENGTH,
.dram_reset = IMX6SDL_DRIVE_STRENGTH,
.dram_sdcke0 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdcke1 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdba2 = 0x00000000,
.dram_sdodt0 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdodt1 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs0 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs1 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs2 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs3 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs4 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs5 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs6 = IMX6SDL_DRIVE_STRENGTH,
.dram_sdqs7 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm0 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm1 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm2 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm3 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm4 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm5 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm6 = IMX6SDL_DRIVE_STRENGTH,
.dram_dqm7 = IMX6SDL_DRIVE_STRENGTH,
};
/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
.grp_ddr_type = 0x000c0000,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_addds = IMX6SDL_DRIVE_STRENGTH,
.grp_ctlds = IMX6SDL_DRIVE_STRENGTH,
.grp_ddrmode = 0x00020000,
.grp_b0ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b1ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b2ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b3ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b4ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b5ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b6ds = IMX6SDL_DRIVE_STRENGTH,
.grp_b7ds = IMX6SDL_DRIVE_STRENGTH,
};
/* MT41K128M16JT-125 */
static struct mx6_ddr3_cfg mt41k128m16jt_125 = {
/* quad = 1066, duallite = 800 */
.mem_speed = 1066,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
.SRT = 0,
};
static struct mx6_mmdc_calibration mx6dl_1g_mmdc_calib = {
.p0_mpwldectrl0 = 0x0043004E,
.p0_mpwldectrl1 = 0x003D003F,
.p1_mpwldectrl0 = 0x00230021,
.p1_mpwldectrl1 = 0x0028003E,
.p0_mpdgctrl0 = 0x42580250,
.p0_mpdgctrl1 = 0x0238023C,
.p1_mpdgctrl0 = 0x422C0238,
.p1_mpdgctrl1 = 0x02180228,
.p0_mprddlctl = 0x44464A46,
.p1_mprddlctl = 0x44464A42,
.p0_mpwrdlctl = 0x36343236,
.p1_mpwrdlctl = 0x36343230,
};
/* DDR 64bit 1GB */
static struct mx6_ddr_sysinfo mem_qdl = {
.dsize = 2,
.cs1_mirror = 0,
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32,
.ncs = 1,
.bi_on = 1,
.rtt_nom = 1,
.rtt_wr = 1,
.ralat = 5,
.walat = 0,
.mif3_mode = 3,
.rst_to_cke = 0x23,
.sde_to_rst = 0x10,
.refsel = 1, /* Refresh cycles at 32KHz */
.refr = 7, /* 8 refresh commands per refresh cycle */
};
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* set the default clock gate to save power */
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0xFFFFFFFF, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void spl_dram_init(void)
{
if (is_cpu_type(MXC_CPU_MX6DL)) {
mt41k128m16jt_125.mem_speed = 800;
mem_qdl.rtt_nom = 1;
mem_qdl.rtt_wr = 1;
mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
mx6_dram_cfg(&mem_qdl, &mx6dl_1g_mmdc_calib, &mt41k128m16jt_125);
} else {
printf("Wrong CPU for this board\n");
return;
}
udelay(100);
#ifdef CONFIG_MX6_DDRCAL
/* Perform DDR DRAM calibration */
mmdc_do_write_level_calibration(&mem_qdl);
mmdc_do_dqs_calibration(&mem_qdl);
#endif
}
static void check_bootcfg(void)
{
u32 val5, val6;
fuse_sense(0, 5, &val5);
fuse_sense(0, 6, &val6);
/* Check if boot from MMC */
if (val6 & 0x10) {
puts("BT_FUSE_SEL already fused, will do nothing\n");
return;
}
fuse_prog(0, 5, 0x00000840);
/* BT_FUSE_SEL */
fuse_prog(0, 6, 0x00000010);
do_reset(NULL, 0, 0, NULL);
}
void board_init_f(ulong dummy)
{
ccgr_init();
/* setup AIPS and disable watchdog */
arch_cpu_init();
gpr_init();
/* iomux */
board_early_init_f();
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* DDR initialization */
spl_dram_init();
/* Set fuses for new boards and reboot if not set */
check_bootcfg();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
#endif
Reference in a new issue View git blame Copy permalink