u-boot/board/engicam/icorem6_rqs
Jagan Teki 6121a54d60 arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial support
Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530)

CPU:   Freescale i.MX6DL rev1.3 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
..
icorem6_rqs.c arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial support 2016-12-16 17:16:10 +01:00
Kconfig arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial support 2016-12-16 17:16:10 +01:00
MAINTAINERS arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial support 2016-12-16 17:16:10 +01:00
Makefile arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial support 2016-12-16 17:16:10 +01:00
README arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial support 2016-12-16 17:16:10 +01:00

How to use U-Boot on Engicam i.CoreM6 RQS Solo/DualLite and Quad/Dual Starter Kit:
----------------------------------------------------------------------------------

$ make mrproper

- Configure U-Boot for Engicam i.CoreM6 RQS Quad/Dual:
$ make imx6q_icore_rqs_mmc_defconfig

- Configure U-Boot for Engicam i.CoreM6 RQS Solo/DualLite:
$ make imx6dl_icore_rqs_mmc_defconfig

- Build U-Boot
$ make

This will generate the SPL image called SPL and the u-boot-dtb.img.

- Flash the SPL image into the micro SD card:

sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync

- Flash the u-boot-dtb.img image into the micro SD card:

sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync

- Jumper settings:

MMC Boot: JM3 Closed

- Connect the Serial cable between the Starter Kit and the PC for the console.
(J28 is the Linux Serial console connector)

- Insert the micro SD card in the board, power it up and U-Boot messages should
come up.