mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-19 09:43:08 +00:00
837833a724
When OE is packaging a dtb file into the FIT image it names the node based on the dtb filename. Node names can't have "/" so it is turned into "_". We select our FIT config using the "fdtfile" env var so we don't duplicate the board_name to fdt logic. Result is fdtfile needs mangled when used to select a config node from OE made FIT image. Do this here. Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
157 lines
5.7 KiB
C
157 lines
5.7 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* ti_armv7_common.h
|
|
*
|
|
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* The various ARMv7 SoCs from TI all share a number of IP blocks when
|
|
* implementing a given feature. Rather than define these in every
|
|
* board or even SoC common file, we define a common file to be re-used
|
|
* in all cases. While technically true that some of these details are
|
|
* configurable at the board design, they are common throughout SoC
|
|
* reference platforms as well as custom designs and become de facto
|
|
* standards.
|
|
*/
|
|
|
|
#ifndef __CONFIG_TI_ARMV7_COMMON_H__
|
|
#define __CONFIG_TI_ARMV7_COMMON_H__
|
|
|
|
/*
|
|
* We setup defaults based on constraints from the Linux kernel, which should
|
|
* also be safe elsewhere. We have the default load at 32MB into DDR (for
|
|
* the kernel), FDT above 128MB (the maximum location for the end of the
|
|
* kernel), and the ramdisk 512KB above that (allowing for hopefully never
|
|
* seen large trees). We say all of this must be within the first 256MB
|
|
* as that will normally be within the kernel lowmem and thus visible via
|
|
* bootm_size and we only run on platforms with 256MB or more of memory.
|
|
*
|
|
* As a temporary storage for DTBO blobs (which should be applied into DTB
|
|
* blob), we use the location 15.5 MB above the ramdisk. If someone wants to
|
|
* use ramdisk bigger than 15.5 MB, then DTBO can be loaded and applied to DTB
|
|
* blob before loading the ramdisk, as DTBO location is only used as a temporary
|
|
* storage, and can be re-used after 'fdt apply' command is done.
|
|
*/
|
|
#define DEFAULT_LINUX_BOOT_ENV \
|
|
"loadaddr=0x82000000\0" \
|
|
"kernel_addr_r=0x82000000\0" \
|
|
"fdtaddr=0x88000000\0" \
|
|
"dtboaddr=0x89000000\0" \
|
|
"fdt_addr_r=0x88000000\0" \
|
|
"fdtoverlay_addr_r=0x89000000\0" \
|
|
"rdaddr=0x88080000\0" \
|
|
"ramdisk_addr_r=0x88080000\0" \
|
|
"scriptaddr=0x80000000\0" \
|
|
"pxefile_addr_r=0x80100000\0" \
|
|
"bootm_size=0x10000000\0" \
|
|
"boot_fdt=try\0"
|
|
|
|
#define DEFAULT_FIT_TI_ARGS \
|
|
"boot_fit=0\0" \
|
|
"addr_fit=0x90000000\0" \
|
|
"name_fit=fitImage\0" \
|
|
"update_to_fit=setenv loadaddr ${addr_fit}; setenv bootfile ${name_fit}\0" \
|
|
"get_overlaystring=" \
|
|
"for overlay in $name_overlays;" \
|
|
"do;" \
|
|
"setenv overlaystring ${overlaystring}'#'${overlay};" \
|
|
"done;\0" \
|
|
"get_fit_config=setexpr name_fit_config gsub / _ conf-${fdtfile}\0" \
|
|
"run_fit=run get_fit_config; bootm ${addr_fit}#${name_fit_config}${overlaystring}\0" \
|
|
|
|
/*
|
|
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
|
|
* we say (for simplicity) that we have 1 bank, always, even when
|
|
* we have more. We always start at 0x80000000, and we place the
|
|
* initial stack pointer in our SRAM. Otherwise, we can define
|
|
* CONFIG_NR_DRAM_BANKS before including this file.
|
|
*/
|
|
#define CFG_SYS_SDRAM_BASE 0x80000000
|
|
|
|
/* If DM_I2C, enable non-DM I2C support */
|
|
|
|
/*
|
|
* The following are general good-enough settings for U-Boot. We set a
|
|
* large malloc pool as we generally have a lot of DDR, and we opt for
|
|
* function over binary size in the main portion of U-Boot as this is
|
|
* generally easily constrained later if needed. We enable the config
|
|
* options that give us information in the environment about what board
|
|
* we are on so we do not need to rely on the command prompt. We set a
|
|
* console baudrate of 115200 and use the default baud rate table.
|
|
*/
|
|
|
|
/* As stated above, the following choices are optional. */
|
|
|
|
/* Console I/O Buffer Size */
|
|
/*
|
|
* When we have SPI, NOR or NAND flash we expect to be making use of
|
|
* mtdparts, both for ease of use in U-Boot and for passing information
|
|
* on to the Linux kernel.
|
|
*/
|
|
|
|
/*
|
|
* Our platforms make use of SPL to initalize the hardware (primarily
|
|
* memory) enough for full U-Boot to be loaded. We make use of the general
|
|
* SPL framework found under common/spl/. Given our generally common memory
|
|
* map, we set a number of related defaults and sizes here.
|
|
*/
|
|
#if !defined(CONFIG_NOR_BOOT) && \
|
|
!(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX))
|
|
|
|
/*
|
|
* We also support Falcon Mode so that the Linux kernel can be booted
|
|
* directly from SPL. This is not currently available on HS devices.
|
|
*/
|
|
|
|
/*
|
|
* Place the image at the start of the ROM defined image space (per
|
|
* CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined
|
|
* downloaded image area minus 1KiB for scratch space. We initalize DRAM as
|
|
* soon as we can so that we can place stack, malloc and BSS there. We load
|
|
* U-Boot itself into memory at 0x80800000 for legacy reasons (to not conflict
|
|
* with older SPLs). We have our BSS be placed 2MiB after this, to allow for
|
|
* the default Linux kernel address of 0x80008000 to work with most sized
|
|
* kernels, in the Falcon Mode case. We have the SPL malloc pool at the end
|
|
* of the BSS area. We suggest that the stack be placed at 32MiB after the
|
|
* start of DRAM to allow room for all of the above (handled in Kconfig).
|
|
*/
|
|
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
/* FAT */
|
|
|
|
/* RAW SD card / eMMC */
|
|
#endif
|
|
|
|
/* General parts of the framework, required. */
|
|
|
|
#ifdef CONFIG_MTD_RAW_NAND
|
|
#define CFG_SYS_NAND_U_BOOT_START CONFIG_TEXT_BASE
|
|
#endif
|
|
#endif /* !CONFIG_NOR_BOOT */
|
|
|
|
/* Generic Environment Variables */
|
|
|
|
#ifdef CONFIG_CMD_NET
|
|
#define NETARGS \
|
|
"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
|
|
"::off\0" \
|
|
"nfsopts=nolock\0" \
|
|
"rootpath=/export/rootfs\0" \
|
|
"netloadimage=tftp ${loadaddr} ${bootfile}\0" \
|
|
"netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
|
|
"netargs=setenv bootargs console=${console} " \
|
|
"${optargs} " \
|
|
"root=/dev/nfs " \
|
|
"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
|
|
"ip=dhcp\0" \
|
|
"netboot=echo Booting from network ...; " \
|
|
"setenv autoload no; " \
|
|
"dhcp; " \
|
|
"run netloadimage; " \
|
|
"run netloadfdt; " \
|
|
"run netargs; " \
|
|
"bootz ${loadaddr} - ${fdtaddr}\0"
|
|
#else
|
|
#define NETARGS ""
|
|
#endif
|
|
|
|
#endif /* __CONFIG_TI_ARMV7_COMMON_H__ */
|