u-boot/board/compulab/cm_t335/cm_t335.c
Mugunthan V N 9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00

162 lines
3.6 KiB
C

/*
* Board functions for Compulab CM-T335 board
*
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
*
* Author: Ilya Ledvich <ilya@compulab.co.il>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <errno.h>
#include <miiphy.h>
#include <cpsw.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/hardware_am33xx.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include "../common/eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
gpmc_init();
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
#endif
return 0;
}
#if defined (CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slave = {
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
.phy_addr = 0,
.phy_if = PHY_INTERFACE_MODE_RGMII,
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x800,
.slaves = 1,
.slave_data = &cpsw_slave,
.ale_reg_ofs = 0xd00,
.ale_entries = 1024,
.host_port_reg_ofs = 0x108,
.hw_stats_reg_ofs = 0x900,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_2,
};
/* PHY reset GPIO */
#define GPIO_PHY_RST GPIO_PIN(3, 7)
static void board_phy_init(void)
{
gpio_request(GPIO_PHY_RST, "phy_rst");
gpio_direction_output(GPIO_PHY_RST, 0);
mdelay(2);
gpio_set_value(GPIO_PHY_RST, 1);
mdelay(2);
}
static void get_efuse_mac_addr(uchar *enetaddr)
{
uint32_t mac_hi, mac_lo;
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
mac_lo = readl(&cdev->macid0l);
mac_hi = readl(&cdev->macid0h);
enetaddr[0] = mac_hi & 0xFF;
enetaddr[1] = (mac_hi & 0xFF00) >> 8;
enetaddr[2] = (mac_hi & 0xFF0000) >> 16;
enetaddr[3] = (mac_hi & 0xFF000000) >> 24;
enetaddr[4] = mac_lo & 0xFF;
enetaddr[5] = (mac_lo & 0xFF00) >> 8;
}
/*
* Routine: handle_mac_address
* Description: prepare MAC address for on-board Ethernet.
*/
static int handle_mac_address(void)
{
uchar enetaddr[6];
int rv;
rv = eth_getenv_enetaddr("ethaddr", enetaddr);
if (rv)
return 0;
rv = cl_eeprom_read_mac_addr(enetaddr);
if (rv)
get_efuse_mac_addr(enetaddr);
if (!is_valid_ether_addr(enetaddr))
return -1;
return eth_setenv_enetaddr("ethaddr", enetaddr);
}
#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
#define AR8051_PHY_DEBUG_DATA_REG 0x1e
#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
#define AR8051_RGMII_TX_CLK_DLY 0x100
int board_eth_init(bd_t *bis)
{
int rv, n = 0;
const char *devname;
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
rv = handle_mac_address();
if (rv)
printf("No MAC address found!\n");
writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel);
board_phy_init();
rv = cpsw_register(&cpsw_data);
if (rv < 0)
printf("Error %d registering CPSW switch\n", rv);
else
n += rv;
/*
* CPSW RGMII Internal Delay Mode is not supported in all PVT
* operating points. So we must set the TX clock delay feature
* in the AR8051 PHY. Since we only support a single ethernet
* device, we only do this for the first instance.
*/
devname = miiphy_get_current_dev();
miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_ADDR_REG,
AR8051_DEBUG_RGMII_CLK_DLY_REG);
miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_DATA_REG,
AR8051_RGMII_TX_CLK_DLY);
return n;
}
#endif /* CONFIG_DRIVER_TI_CPSW && !CONFIG_SPL_BUILD */