mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
3765b3e7bd
Signed-off-by: Wolfgang Denk <wd@denx.de>
357 lines
10 KiB
C
357 lines
10 KiB
C
/*
|
|
* (C) Copyright 2006-2007
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/ppc4xx.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <spd_sdram.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
|
|
|
|
static inline u32 get_async_pci_freq(void)
|
|
{
|
|
if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) &
|
|
CONFIG_SYS_BCSR5_PCI66EN)
|
|
return 66666666;
|
|
else
|
|
return 33333333;
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
register uint reg;
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup the external bus controller/chip selects
|
|
*-------------------------------------------------------------------*/
|
|
mtdcr(EBC0_CFGADDR, EBC0_CFG);
|
|
reg = mfdcr(EBC0_CFGDATA);
|
|
mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup the GPIO pins
|
|
*-------------------------------------------------------------------*/
|
|
/*CPLD cs */
|
|
/*setup Address lines for flash size 64Meg. */
|
|
out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x50010000);
|
|
out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x50010000);
|
|
out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x50000000);
|
|
|
|
/*setup emac */
|
|
out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080);
|
|
out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40);
|
|
out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55);
|
|
out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000);
|
|
out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000);
|
|
|
|
/*UART1 */
|
|
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x02000000);
|
|
out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x00080000);
|
|
out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x00010000);
|
|
|
|
/* external interrupts IRQ0...3 */
|
|
out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000);
|
|
out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00);
|
|
out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500);
|
|
|
|
#ifdef CONFIG_440EP
|
|
/*setup USB 2.0 */
|
|
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000);
|
|
out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000);
|
|
out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf);
|
|
out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa);
|
|
out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500);
|
|
#endif
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup the interrupt controller polarities, triggers, etc.
|
|
*-------------------------------------------------------------------*/
|
|
mtdcr(UIC0SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC0ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC0CR, 0x00000009); /* ATI & UIC1 crit are critical */
|
|
mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
|
|
mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
|
|
mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC0SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr(UIC1SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC1ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC1CR, 0x00000000); /* all non-critical */
|
|
mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
|
|
mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
|
|
mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC1SR, 0xffffffff); /* clear all */
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup other serial configuration
|
|
*-------------------------------------------------------------------*/
|
|
mfsdr(SDR0_PCI0, reg);
|
|
mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
|
|
mtsdr(SDR0_PFC0, 0x00003e00); /* Pin function */
|
|
mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins */
|
|
|
|
/* Check and reconfigure the PCI sync clock if necessary */
|
|
ppc4xx_pci_sync_clock_config(get_async_pci_freq());
|
|
|
|
/*clear tmrclk divisor */
|
|
*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x04) = 0x00;
|
|
|
|
/*enable ethernet */
|
|
*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x08) = 0xf0;
|
|
|
|
#ifdef CONFIG_440EP
|
|
/*enable usb 1.1 fs device and remove usb 2.0 reset */
|
|
*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x09) = 0x00;
|
|
#endif
|
|
|
|
/*get rid of flash write protect */
|
|
*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x07) = 0x00;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r (void)
|
|
{
|
|
uint pbcr;
|
|
int size_val = 0;
|
|
|
|
/* Re-do sizing to get full correct info */
|
|
mtdcr(EBC0_CFGADDR, PB0CR);
|
|
pbcr = mfdcr(EBC0_CFGDATA);
|
|
switch (gd->bd->bi_flashsize) {
|
|
case 1 << 20:
|
|
size_val = 0;
|
|
break;
|
|
case 2 << 20:
|
|
size_val = 1;
|
|
break;
|
|
case 4 << 20:
|
|
size_val = 2;
|
|
break;
|
|
case 8 << 20:
|
|
size_val = 3;
|
|
break;
|
|
case 16 << 20:
|
|
size_val = 4;
|
|
break;
|
|
case 32 << 20:
|
|
size_val = 5;
|
|
break;
|
|
case 64 << 20:
|
|
size_val = 6;
|
|
break;
|
|
case 128 << 20:
|
|
size_val = 7;
|
|
break;
|
|
}
|
|
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
|
|
mtdcr(EBC0_CFGADDR, PB0CR);
|
|
mtdcr(EBC0_CFGDATA, pbcr);
|
|
|
|
/* adjust flash start and offset */
|
|
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
|
|
gd->bd->bi_flashoffset = 0;
|
|
|
|
/* Monitor protection ON by default */
|
|
(void)flash_protect(FLAG_PROTECT_SET,
|
|
-CONFIG_SYS_MONITOR_LEN,
|
|
0xffffffff,
|
|
&flash_info[0]);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char buf[64];
|
|
int i = getenv_f("serial#", buf, sizeof(buf));
|
|
u8 rev;
|
|
u32 clock = get_async_pci_freq();
|
|
|
|
#ifdef CONFIG_440EP
|
|
printf("Board: Yosemite - AMCC PPC440EP Evaluation Board");
|
|
#else
|
|
printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board");
|
|
#endif
|
|
|
|
rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0));
|
|
printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000);
|
|
|
|
if (i > 0) {
|
|
puts(", serial# ");
|
|
puts(buf);
|
|
}
|
|
putc('\n');
|
|
|
|
/*
|
|
* Reconfiguration of the PCI sync clock is already done,
|
|
* now check again if everything is in range:
|
|
*/
|
|
if (ppc4xx_pci_sync_clock_config(clock)) {
|
|
printf("ERROR: PCI clocking incorrect (async=%d "
|
|
"sync=%ld)!\n", clock, get_PCI_freq());
|
|
}
|
|
|
|
return (0);
|
|
}
|
|
|
|
/*************************************************************************
|
|
* initdram -- doesn't use serial presence detect.
|
|
*
|
|
* Assumes: 256 MB, ECC, non-registered
|
|
* PLB @ 133 MHz
|
|
*
|
|
************************************************************************/
|
|
#define NUM_TRIES 64
|
|
#define NUM_READS 10
|
|
|
|
void sdram_tr1_set(int ram_address, int* tr1_value)
|
|
{
|
|
int i;
|
|
int j, k;
|
|
volatile unsigned int* ram_pointer = (unsigned int*)ram_address;
|
|
int first_good = -1, last_bad = 0x1ff;
|
|
|
|
unsigned long test[NUM_TRIES] = {
|
|
0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
|
|
0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
|
|
0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
|
|
0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
|
|
0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
|
|
0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
|
|
0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
|
|
0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
|
|
0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
|
|
0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
|
|
0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
|
|
0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
|
|
0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
|
|
0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
|
|
0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
|
|
0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 };
|
|
|
|
/* go through all possible SDRAM0_TR1[RDCT] values */
|
|
for (i=0; i<=0x1ff; i++) {
|
|
/* set the current value for TR1 */
|
|
mtsdram(SDRAM0_TR1, (0x80800800 | i));
|
|
|
|
/* write values */
|
|
for (j=0; j<NUM_TRIES; j++) {
|
|
ram_pointer[j] = test[j];
|
|
|
|
/* clear any cache at ram location */
|
|
__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
|
|
}
|
|
|
|
/* read values back */
|
|
for (j=0; j<NUM_TRIES; j++) {
|
|
for (k=0; k<NUM_READS; k++) {
|
|
/* clear any cache at ram location */
|
|
__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
|
|
|
|
if (ram_pointer[j] != test[j])
|
|
break;
|
|
}
|
|
|
|
/* read error */
|
|
if (k != NUM_READS) {
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* we have a SDRAM0_TR1[RDCT] that is part of the window */
|
|
if (j == NUM_TRIES) {
|
|
if (first_good == -1)
|
|
first_good = i; /* found beginning of window */
|
|
} else { /* bad read */
|
|
/* if we have not had a good read then don't care */
|
|
if(first_good != -1) {
|
|
/* first failure after a good read */
|
|
last_bad = i-1;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* return the current value for TR1 */
|
|
*tr1_value = (first_good + last_bad) / 2;
|
|
}
|
|
|
|
phys_size_t initdram(int board)
|
|
{
|
|
register uint reg;
|
|
int tr1_bank1, tr1_bank2;
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup some default
|
|
*------------------------------------------------------------------*/
|
|
mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
|
|
mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
|
|
mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
|
|
mtsdram(SDRAM0_CLKTR, 0x40000000); /* ?? */
|
|
mtsdram(SDRAM0_WDDCTR, 0x40000000); /* ?? */
|
|
|
|
/*clear this first, if the DDR is enabled by a debugger
|
|
then you can not make changes. */
|
|
mtsdram(SDRAM0_CFG0, 0x00000000); /* Disable EEC */
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup for board-specific specific mem
|
|
*------------------------------------------------------------------*/
|
|
/*
|
|
* Following for CAS Latency = 2.5 @ 133 MHz PLB
|
|
*/
|
|
mtsdram(SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
|
|
mtsdram(SDRAM0_B1CR, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */
|
|
|
|
mtsdram(SDRAM0_TR0, 0x410a4012); /* ?? */
|
|
mtsdram(SDRAM0_RTR, 0x04080000); /* ?? */
|
|
mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
|
|
mtsdram(SDRAM0_CFG0, 0x30000000); /* Disable EEC */
|
|
udelay(400); /* Delay 200 usecs (min) */
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Enable the controller, then wait for DCEN to complete
|
|
*------------------------------------------------------------------*/
|
|
mtsdram(SDRAM0_CFG0, 0x80000000); /* Enable */
|
|
|
|
for (;;) {
|
|
mfsdram(SDRAM0_MCSTS, reg);
|
|
if (reg & 0x80000000)
|
|
break;
|
|
}
|
|
|
|
sdram_tr1_set(0x00000000, &tr1_bank1);
|
|
sdram_tr1_set(0x08000000, &tr1_bank2);
|
|
mtsdram(SDRAM0_TR1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
|
|
|
|
return CONFIG_SYS_SDRAM_BANKS * (CONFIG_SYS_KBYTES_SDRAM * 1024); /* return bytes */
|
|
}
|
|
|
|
/*************************************************************************
|
|
* hw_watchdog_reset
|
|
*
|
|
* This routine is called to reset (keep alive) the watchdog timer
|
|
*
|
|
************************************************************************/
|
|
#if defined(CONFIG_HW_WATCHDOG)
|
|
void hw_watchdog_reset(void)
|
|
{
|
|
|
|
}
|
|
#endif
|
|
|
|
void board_reset(void)
|
|
{
|
|
/* give reset to BCSR */
|
|
*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x06) = 0x09;
|
|
}
|