mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-10-20 13:04:51 +00:00
dcfd37e5ef
The change adds support of LPC32xx SLC NAND controller. LPC32xx SoC has two different mutually exclusive NAND controllers to communicate with single and multiple layer chips. This simple driver allows to specify NAND chip timings and defines custom read_buf()/write_buf() operations, because access to 8-bit data register must be 32-bit aligned. Support of hardware ECC calculation is not implemented (data correction is always done by software), since it requires a working DMA engine. The driver can be included to an SPL image. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Scott Wood <scottwood@freescale.com> Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
88 lines
2 KiB
C
88 lines
2 KiB
C
/*
|
|
* Copyright (C) 2011 by Vladimir Zapolskiy <vz@mleia.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <asm/arch/uart.h>
|
|
#include <asm/arch/mux.h>
|
|
#include <asm/io.h>
|
|
#include <dm.h>
|
|
|
|
static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
|
|
static struct uart_ctrl_regs *ctrl = (struct uart_ctrl_regs *)UART_CTRL_BASE;
|
|
static struct mux_regs *mux = (struct mux_regs *)MUX_BASE;
|
|
|
|
void lpc32xx_uart_init(unsigned int uart_id)
|
|
{
|
|
if (uart_id < 1 || uart_id > 7)
|
|
return;
|
|
|
|
/* Disable loopback mode, if it is set by S1L bootloader */
|
|
clrbits_le32(&ctrl->loop,
|
|
UART_LOOPBACK(CONFIG_SYS_LPC32XX_UART));
|
|
|
|
if (uart_id < 3 || uart_id > 6)
|
|
return;
|
|
|
|
/* Enable UART system clock */
|
|
setbits_le32(&clk->uartclk_ctrl, CLK_UART(uart_id));
|
|
|
|
/* Set UART into autoclock mode */
|
|
clrsetbits_le32(&ctrl->clkmode,
|
|
UART_CLKMODE_MASK(uart_id),
|
|
UART_CLKMODE_AUTO(uart_id));
|
|
|
|
/* Bypass pre-divider of UART clock */
|
|
writel(CLK_UART_X_DIV(1) | CLK_UART_Y_DIV(1),
|
|
&clk->u3clk + (uart_id - 3));
|
|
}
|
|
|
|
void lpc32xx_mac_init(void)
|
|
{
|
|
/* Enable MAC interface */
|
|
writel(CLK_MAC_REG | CLK_MAC_SLAVE | CLK_MAC_MASTER
|
|
| CLK_MAC_MII, &clk->macclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_mlc_nand_init(void)
|
|
{
|
|
/* Enable NAND interface */
|
|
writel(CLK_NAND_MLC | CLK_NAND_MLC_INT, &clk->flashclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_slc_nand_init(void)
|
|
{
|
|
/* Enable SLC NAND interface */
|
|
writel(CLK_NAND_SLC | CLK_NAND_SLC_SELECT, &clk->flashclk_ctrl);
|
|
}
|
|
|
|
void lpc32xx_i2c_init(unsigned int devnum)
|
|
{
|
|
/* Enable I2C interface */
|
|
uint32_t ctrl = readl(&clk->i2cclk_ctrl);
|
|
if (devnum == 1)
|
|
ctrl |= CLK_I2C1_ENABLE;
|
|
if (devnum == 2)
|
|
ctrl |= CLK_I2C2_ENABLE;
|
|
writel(ctrl, &clk->i2cclk_ctrl);
|
|
}
|
|
|
|
U_BOOT_DEVICE(lpc32xx_gpios) = {
|
|
.name = "gpio_lpc32xx"
|
|
};
|
|
|
|
/* Mux for SCK0, MISO0, MOSI0. We do not use SSEL0. */
|
|
|
|
#define P_MUX_SET_SSP0 0x1600
|
|
|
|
void lpc32xx_ssp_init(void)
|
|
{
|
|
/* Enable SSP0 interface */
|
|
writel(CLK_SSP0_ENABLE_CLOCK, &clk->ssp_ctrl);
|
|
/* Mux SSP0 pins */
|
|
writel(P_MUX_SET_SSP0, &mux->p_mux_set);
|
|
}
|