u-boot/drivers/spi/Kconfig
Jagan Teki dc738248db spi: Kconfig: Enable SPI_SUNXI for SUNXI
SPI_SUNXI driver is fully dm-aware and the Allwinner
architecture kconfig would have logic to enable the
DM_SPI. So, select default spi sunxi driver for
sunxi architecture.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:31 +05:30

451 lines
14 KiB
Text

menuconfig SPI
bool "SPI Support"
help
The "Serial Peripheral Interface" is a low level synchronous
protocol. Chips that support SPI can have data transfer rates
up to several tens of Mbit/sec. Chips are addressed with a
controller and a chipselect. Most SPI slaves don't support
dynamic device discovery; some are even write-only or read-only.
SPI is widely used by microcontrollers to talk with sensors,
eeprom and flash memory, codecs and various other controller
chips, analog to digital (and d-to-a) converters, and more.
MMC and SD cards can be accessed using SPI protocol; and for
DataFlash cards used in MMC sockets, SPI must always be used.
SPI is one of a family of similar protocols using a four wire
interface (select, clock, data in, data out) including Microwire
(half duplex), SSP, SSI, and PSP. This driver framework should
work with most such devices and controllers.
if SPI
config DM_SPI
bool "Enable Driver Model for SPI drivers"
depends on DM
help
Enable driver model for SPI. The SPI slave interface
(spi_setup_slave(), spi_xfer(), etc.) is then implemented by
the SPI uclass. Drivers provide methods to access the SPI
buses that they control. The uclass interface is defined in
include/spi.h. The existing spi_slave structure is attached
as 'parent data' to every slave on each bus. Slaves
typically use driver-private data instead of extending the
spi_slave structure.
config SPI_MEM
bool "SPI memory extension"
help
Enable this option if you want to enable the SPI memory extension.
This extension is meant to simplify interaction with SPI memories
by providing an high-level interface to send memory-like commands.
if DM_SPI
config ALTERA_SPI
bool "Altera SPI driver"
help
Enable the Altera SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Altera
IP core. Please find details on the "Embedded Peripherals IP
User Guide" of Altera.
config ATCSPI200_SPI
bool "Andestech ATCSPI200 SPI driver"
help
Enable the Andestech ATCSPI200 SPI driver. This driver can be
used to access the SPI flash on AE3XX and AE250 platforms embedding
this Andestech IP core.
config ATH79_SPI
bool "Atheros SPI driver"
depends on ARCH_ATH79
help
Enable the Atheros ar7xxx/ar9xxx SoC SPI driver, it was used
to access SPI NOR flash and other SPI peripherals. This driver
uses driver model and requires a device tree binding to operate.
please refer to doc/device-tree-bindings/spi/spi-ath79.txt.
config ATMEL_QSPI
bool "Atmel Quad SPI Controller"
depends on ARCH_AT91
help
Enable the Atmel Quad SPI controller in master mode. This driver
does not support generic SPI. The implementation supports only the
spi-mem interface.
config ATMEL_SPI
bool "Atmel SPI driver"
default y if ARCH_AT91
help
This enables driver for the Atmel SPI Controller, present on
many AT91 (ARM) chips. This driver can be used to access
the SPI Flash, such as AT25DF321.
config BCM63XX_HSSPI
bool "BCM63XX HSSPI driver"
depends on (ARCH_BMIPS || ARCH_BCM6858 || ARCH_BCM63158)
help
Enable the BCM6328 HSSPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Broadcom
SPI core.
config BCM63XX_SPI
bool "BCM6348 SPI driver"
depends on ARCH_BMIPS
help
Enable the BCM6348/BCM6358 SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding these Broadcom
SPI cores.
config BCMSTB_SPI
bool "BCMSTB SPI driver"
help
Enable the Broadcom set-top box SPI driver. This driver can
be used to access the SPI flash on platforms embedding this
Broadcom SPI core.
config CADENCE_QSPI
bool "Cadence QSPI driver"
help
Enable the Cadence Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Cadence IP core.
config CF_SPI
bool "ColdFire SPI driver"
help
Enable the ColdFire SPI driver. This driver can be used on
some m68k SoCs.
config DESIGNWARE_SPI
bool "Designware SPI driver"
help
Enable the Designware SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Designware
IP core.
config EXYNOS_SPI
bool "Samsung Exynos SPI driver"
help
Enable the Samsung Exynos SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Samsung
Exynos IP core.
config FSL_DSPI
bool "Freescale DSPI driver"
help
Enable the Freescale DSPI driver. This driver can be used to
access the SPI NOR flash and SPI Data flash on platforms embedding
this Freescale DSPI IP core. LS102xA and Colibri VF50/VF61 platforms
use this driver.
config ICH_SPI
bool "Intel ICH SPI driver"
imply SPI_FLASH_BAR
help
Enable the Intel ICH SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Intel
ICH IP core.
config MESON_SPIFC
bool "Amlogic Meson SPI Flash Controller driver"
depends on ARCH_MESON
help
Enable the Amlogic Meson SPI Flash Controller SPIFC) driver.
This driver can be used to access the SPI NOR flash chips on
Amlogic Meson SoCs.
config MPC8XX_SPI
bool "MPC8XX SPI Driver"
depends on MPC8xx
help
Enable support for SPI on MPC8XX
config MPC8XXX_SPI
bool "MPC8XXX SPI Driver"
help
Enable support for SPI on the MPC8XXX PowerPC SoCs.
config MT7621_SPI
bool "MediaTek MT7621 SPI driver"
depends on SOC_MT7628
help
Enable the MT7621 SPI driver. This driver can be used to access
the SPI NOR flash on platforms embedding this Ralink / MediaTek
SPI core, like MT7621/7628/7688.
config MTK_SNFI_SPI
bool "Mediatek SPI memory controller driver"
depends on SPI_MEM
help
Enable the Mediatek SPI memory controller driver. This driver is
originally based on the MediaTek SNFI IP core. It can only be
used to access SPI memory devices like SPI-NOR or SPI-NAND on
platforms embedding this IP core, like MT7622/M7629.
config MVEBU_A3700_SPI
bool "Marvell Armada 3700 SPI driver"
select CLK_ARMADA_3720
help
Enable the Marvell Armada 3700 SPI driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Marvell IP core.
config PIC32_SPI
bool "Microchip PIC32 SPI driver"
depends on MACH_PIC32
help
Enable the Microchip PIC32 SPI driver. This driver can be used
to access the SPI NOR flash, MMC-over-SPI on platforms based on
Microchip PIC32 family devices.
config PL022_SPI
bool "ARM AMBA PL022 SSP controller driver"
depends on ARM
help
This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
controller. If you have an embedded system with an AMBA(R)
bus and a PL022 controller, say Y or M here.
config RENESAS_RPC_SPI
bool "Renesas RPC SPI driver"
depends on RCAR_GEN3 || RZA1
imply SPI_FLASH_BAR
help
Enable the Renesas RPC SPI driver, used to access SPI NOR flash
on Renesas RCar Gen3 SoCs. This uses driver model and requires a
device tree binding to operate.
config ROCKCHIP_SPI
bool "Rockchip SPI driver"
help
Enable the Rockchip SPI driver, used to access SPI NOR flash and
other SPI peripherals (such as the Chrome OS EC) on Rockchip SoCs.
This uses driver model and requires a device tree binding to
operate.
config SANDBOX_SPI
bool "Sandbox SPI driver"
depends on SANDBOX && DM
help
Enable SPI support for sandbox. This is an emulation of a real SPI
bus. Devices can be attached to the bus using the device tree
which specifies the driver to use. As an example, see this device
tree fragment from sandbox.dts. It shows that the SPI bus has a
single flash device on chip select 0 which is emulated by the driver
for "sandbox,spi-flash", which is in drivers/mtd/spi/sandbox.c.
spi@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
compatible = "sandbox,spi";
cs-gpios = <0>, <&gpio_a 0>;
flash@0 {
reg = <0>;
compatible = "spansion,m25p16", "jedec,spi-nor";
spi-max-frequency = <40000000>;
sandbox,filename = "spi.bin";
};
};
config SPI_SIFIVE
bool "SiFive SPI driver"
help
This driver supports the SiFive SPI IP. If unsure say N.
Enable the SiFive SPI controller driver.
The SiFive SPI controller driver is found on various SiFive SoCs.
config SPI_SUNXI
bool "Allwinner SoC SPI controllers"
default ARCH_SUNXI
help
Enable the Allwinner SoC SPi controller driver.
Same controller driver can reuse in all Allwinner SoC variants.
config STM32_QSPI
bool "STM32F7 QSPI driver"
depends on STM32F4 || STM32F7 || ARCH_STM32MP
help
Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash chips on platforms embedding
this ST IP core.
config STM32_SPI
bool "STM32 SPI driver"
depends on ARCH_STM32MP
help
Enable the STM32 Serial Peripheral Interface (SPI) driver for STM32MP
SoCs. This uses driver model and requires a device tree binding to
operate.
config TEGRA114_SPI
bool "nVidia Tegra114 SPI driver"
help
Enable the nVidia Tegra114 SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this nVidia Tegra114
IP core.
This controller is different than the older SoCs SPI controller and
also register interface get changed with this controller.
config TEGRA20_SFLASH
bool "nVidia Tegra20 Serial Flash controller driver"
help
Enable the nVidia Tegra20 Serial Flash controller driver. This driver
can be used to access the SPI NOR flash on platforms embedding this
nVidia Tegra20 IP core.
config TEGRA20_SLINK
bool "nVidia Tegra20/Tegra30 SLINK driver"
help
Enable the nVidia Tegra20/Tegra30 SLINK driver. This driver can
be used to access the SPI NOR flash on platforms embedding this
nVidia Tegra20/Tegra30 IP cores.
config TEGRA210_QSPI
bool "nVidia Tegra210 QSPI driver"
help
Enable the Tegra Quad-SPI (QSPI) driver for T210. This driver
be used to access SPI chips on platforms embedding this
NVIDIA Tegra210 IP core.
config TI_QSPI
bool "TI QSPI driver"
imply TI_EDMA3
help
Enable the TI Quad-SPI (QSPI) driver for DRA7xx and AM43xx evms.
This driver support spi flash single, quad and memory reads.
config UNIPHIER_SPI
bool "Socionext UniPhier SPI driver"
depends on ARCH_UNIPHIER
help
Enable the Socionext UniPhier SPI driver. This driver can
be used to access SPI chips on platforms embedding this
UniPhier IP core.
config XILINX_SPI
bool "Xilinx SPI driver"
help
Enable the Xilinx SPI driver from the Xilinx EDK. This SPI
controller support 8 bit SPI transfers only, with or w/o FIFO.
For more info on Xilinx SPI Register Definitions and Overview
see driver file - drivers/spi/xilinx_spi.c
config ZYNQ_SPI
bool "Zynq SPI driver"
depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL
help
Enable the Zynq SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Zynq
SPI IP core.
config ZYNQ_QSPI
bool "Zynq QSPI driver"
depends on ARCH_ZYNQ
imply SPI_FLASH_BAR
help
Enable the Zynq Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Zynq QSPI IP core. This IP is used to connect the flash in
4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel.
config ZYNQMP_GQSPI
bool "Configure ZynqMP Generic QSPI"
depends on ARCH_ZYNQMP || ARCH_VERSAL
help
This option is used to enable ZynqMP QSPI controller driver which
is used to communicate with qspi flash devices.
endif # if DM_SPI
config SOFT_SPI
bool "Soft SPI driver"
depends on DM_SPI || (DEPRECATED && !DM_SPI)
help
Enable Soft SPI driver. This driver is to use GPIO simulate
the SPI protocol.
config MSCC_BB_SPI
bool "MSCC bitbang SPI driver"
depends on SOC_VCOREIII
help
Enable MSCC bitbang SPI driver. This driver can be used on
MSCC SOCs.
config CF_SPI
bool "ColdFire SPI driver"
help
Enable the ColdFire SPI driver. This driver can be used on
some m68k SoCs.
config FSL_ESPI
bool "Freescale eSPI driver"
help
Enable the Freescale eSPI driver. This driver can be used to
access the SPI interface and SPI NOR flash on platforms embedding
this Freescale eSPI IP core.
config FSL_QSPI
bool "Freescale QSPI driver"
imply SPI_FLASH_BAR
help
Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Freescale IP core.
config DAVINCI_SPI
bool "Davinci & Keystone SPI driver"
depends on ARCH_DAVINCI || ARCH_KEYSTONE
help
Enable the Davinci SPI driver
config SH_SPI
bool "SuperH SPI driver"
depends on DEPRECATED
help
Enable the SuperH SPI controller driver. This driver can be used
on various SuperH SoCs, such as SH7757.
config SH_QSPI
bool "Renesas Quad SPI driver"
help
Enable the Renesas Quad SPI controller driver. This driver can be
used on Renesas SoCs.
config KIRKWOOD_SPI
bool "Marvell Kirkwood SPI Driver"
help
Enable support for SPI on various Marvell SoCs, such as
Kirkwood and Armada 375.
config LPC32XX_SSP
bool "LPC32XX SPI Driver"
depends on DEPRECATED
help
Enable support for SPI on LPC32xx
config MXC_SPI
bool "MXC SPI Driver"
help
Enable the MXC SPI controller driver. This driver can be used
on various i.MX SoCs such as i.MX31/35/51/6/7.
config MXS_SPI
bool "MXS SPI Driver"
help
Enable the MXS SPI controller driver. This driver can be used
on the i.MX23 and i.MX28 SoCs.
config OMAP3_SPI
bool "McSPI driver for OMAP"
help
SPI master controller for OMAP24XX and later Multichannel SPI
(McSPI). This driver be used to access SPI chips on platforms
embedding this OMAP3 McSPI IP core.
endif # menu "SPI Support"