mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 04:23:46 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
263 lines
7.1 KiB
C
263 lines
7.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015-2019 Variscite Ltd.
|
|
* Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
|
|
* Copyright (C) 2021 Marc Ferland, Amotus Solutions Inc., <ferlandm@amotus.ca>
|
|
*/
|
|
|
|
#include <init.h>
|
|
#include <net.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <dm.h>
|
|
#include <fsl_esdhc_imx.h>
|
|
#include <i2c_eeprom.h>
|
|
#include <linux/bitops.h>
|
|
#include <malloc.h>
|
|
#include <miiphy.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_NAND_MXS
|
|
#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
|
|
#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_SRE_FAST)
|
|
#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
|
|
static iomux_v3_cfg_t const nand_pads[] = {
|
|
MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
MX6_PAD_NAND_DQS__RAWNAND_DQS | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
|
|
};
|
|
|
|
static void setup_gpmi_nand(void)
|
|
{
|
|
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
|
|
/* config gpmi nand iomux */
|
|
imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
|
|
|
|
clrbits_le32(&mxc_ccm->CCGR4,
|
|
MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
|
|
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
|
|
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
|
|
MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
|
|
MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
|
|
|
|
/*
|
|
* config gpmi and bch clock to 100 MHz
|
|
* bch/gpmi select PLL2 PFD2 400M
|
|
* 100M = 400M / 4
|
|
*/
|
|
clrbits_le32(&mxc_ccm->cscmr1,
|
|
MXC_CCM_CSCMR1_BCH_CLK_SEL |
|
|
MXC_CCM_CSCMR1_GPMI_CLK_SEL);
|
|
clrsetbits_le32(&mxc_ccm->cscdr1,
|
|
MXC_CCM_CSCDR1_BCH_PODF_MASK |
|
|
MXC_CCM_CSCDR1_GPMI_PODF_MASK,
|
|
(3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
|
|
(3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
|
|
|
|
/* enable gpmi and bch clock gating */
|
|
setbits_le32(&mxc_ccm->CCGR4,
|
|
MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
|
|
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
|
|
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
|
|
MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
|
|
MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
|
|
|
|
/* enable apbh clock gating */
|
|
setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
static int setup_fec(int fec_id)
|
|
{
|
|
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
int ret;
|
|
|
|
if (fec_id == 0) {
|
|
/*
|
|
* Use 50M anatop loopback REF_CLK1 for ENET1,
|
|
* clear gpr1[13], set gpr1[17].
|
|
*/
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
|
|
IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
|
|
} else {
|
|
/*
|
|
* Use 50M anatop loopback REF_CLK2 for ENET2,
|
|
* clear gpr1[14], set gpr1[18].
|
|
*/
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
|
|
IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
|
|
}
|
|
|
|
ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
|
|
if (ret)
|
|
return ret;
|
|
|
|
enable_enet_clk(1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
/*
|
|
* Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
|
|
* 50 MHz RMII clock mode.
|
|
*/
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_FEC_MXC */
|
|
|
|
int board_init(void)
|
|
{
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
setup_fec(CONFIG_FEC_ENET_DEV);
|
|
#endif
|
|
|
|
#ifdef CONFIG_NAND_MXS
|
|
setup_gpmi_nand();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
/* length of strings stored in the eeprom */
|
|
#define DART6UL_PN_LEN 16
|
|
#define DART6UL_ASSY_LEN 16
|
|
#define DART6UL_DATE_LEN 12
|
|
|
|
/* eeprom content, 512 bytes */
|
|
struct dart6ul_info {
|
|
u32 magic;
|
|
u8 partnumber[DART6UL_PN_LEN];
|
|
u8 assy[DART6UL_ASSY_LEN];
|
|
u8 date[DART6UL_DATE_LEN];
|
|
u32 custom_addr_val[32];
|
|
struct cmd {
|
|
u8 addr;
|
|
u8 index;
|
|
} custom_cmd[150];
|
|
u8 res[33];
|
|
u8 som_info;
|
|
u8 ddr_size;
|
|
u8 crc;
|
|
} __attribute__ ((__packed__));
|
|
|
|
#define DART6UL_INFO_STORAGE_GET(n) ((n) & 0x3)
|
|
#define DART6UL_INFO_WIFI_GET(n) ((n) >> 2 & 0x1)
|
|
#define DART6UL_INFO_REV_GET(n) ((n) >> 3 & 0x3)
|
|
#define DART6UL_DDRSIZE(n) ((n) * SZ_128M)
|
|
#define DART6UL_INFO_MAGIC 0x32524156
|
|
|
|
static const char *som_info_storage_to_str(u8 som_info)
|
|
{
|
|
switch (DART6UL_INFO_STORAGE_GET(som_info)) {
|
|
case 0x0: return "none (SD only)";
|
|
case 0x1: return "NAND";
|
|
case 0x2: return "eMMC";
|
|
default: return "unknown";
|
|
}
|
|
}
|
|
|
|
static const char *som_info_rev_to_str(u8 som_info)
|
|
{
|
|
switch (DART6UL_INFO_REV_GET(som_info)) {
|
|
case 0x0: return "2.4G";
|
|
case 0x1: return "5G";
|
|
default: return "unknown";
|
|
}
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
const char *path = "eeprom0";
|
|
struct dart6ul_info *info;
|
|
struct udevice *dev;
|
|
int ret, off;
|
|
|
|
off = fdt_path_offset(gd->fdt_blob, path);
|
|
if (off < 0) {
|
|
printf("%s: fdt_path_offset() failed: %d\n", __func__, off);
|
|
return off;
|
|
}
|
|
|
|
ret = uclass_get_device_by_of_offset(UCLASS_I2C_EEPROM, off, &dev);
|
|
if (ret) {
|
|
printf("%s: uclass_get_device_by_of_offset() failed: %d\n", __func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
info = malloc(sizeof(struct dart6ul_info));
|
|
if (!info)
|
|
return -ENOMEM;
|
|
|
|
ret = i2c_eeprom_read(dev, 0, (uint8_t *)info,
|
|
sizeof(struct dart6ul_info));
|
|
if (ret) {
|
|
printf("%s: i2c_eeprom_read() failed: %d\n", __func__, ret);
|
|
free(info);
|
|
return ret;
|
|
}
|
|
|
|
if (info->magic != DART6UL_INFO_MAGIC) {
|
|
printf("Board: Invalid board info magic: 0x%08x, expected 0x%08x\n",
|
|
info->magic, DART6UL_INFO_MAGIC);
|
|
/* do not fail if the content is invalid */
|
|
free(info);
|
|
return 0;
|
|
}
|
|
|
|
/* make sure strings are null terminated */
|
|
info->partnumber[DART6UL_PN_LEN - 1] = '\0';
|
|
info->assy[DART6UL_ASSY_LEN - 1] = '\0';
|
|
info->date[DART6UL_DATE_LEN - 1] = '\0';
|
|
|
|
printf("Board: PN: %s, Assy: %s, Date: %s\n"
|
|
" Storage: %s, Wifi: %s, DDR: %d MiB, Rev: %s\n",
|
|
info->partnumber,
|
|
info->assy,
|
|
info->date,
|
|
som_info_storage_to_str(info->som_info),
|
|
DART6UL_INFO_WIFI_GET(info->som_info) ? "yes" : "no",
|
|
DART6UL_DDRSIZE(info->ddr_size) / SZ_1M,
|
|
som_info_rev_to_str(info->som_info));
|
|
|
|
free(info);
|
|
|
|
return 0;
|
|
}
|