mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-08 22:24:32 +00:00
4dde343d7e
AQR107 PHYs interrupt pins are active-low, while the GIC expects a level-high signal. Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
110 lines
3 KiB
C
110 lines
3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright 2018 NXP
|
|
*/
|
|
|
|
#ifndef __LX2_RDB_H
|
|
#define __LX2_RDB_H
|
|
|
|
#include "lx2160a_common.h"
|
|
|
|
/* Qixis */
|
|
#define QIXIS_XMAP_MASK 0x07
|
|
#define QIXIS_XMAP_SHIFT 5
|
|
#define QIXIS_RST_CTL_RESET_EN 0x30
|
|
#define QIXIS_LBMAP_DFLTBANK 0x00
|
|
#define QIXIS_LBMAP_ALTBANK 0x20
|
|
#define QIXIS_LBMAP_QSPI 0x00
|
|
#define QIXIS_RCW_SRC_QSPI 0xff
|
|
#define QIXIS_RST_CTL_RESET 0x31
|
|
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
|
|
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
|
|
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
|
#define QIXIS_LBMAP_MASK 0x0f
|
|
#define QIXIS_LBMAP_SD
|
|
#define QIXIS_RCW_SRC_SD 0x08
|
|
#define NON_EXTENDED_DUTCFG
|
|
|
|
/* VID */
|
|
|
|
#define I2C_MUX_CH_VOL_MONITOR 0xA
|
|
/* Voltage monitor on channel 2*/
|
|
#define I2C_VOL_MONITOR_ADDR 0x63
|
|
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
|
|
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
|
|
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
|
|
#define CONFIG_VID_FLS_ENV "lx2160ardb_vdd_mv"
|
|
#define CONFIG_VID
|
|
|
|
/* The lowest and highest voltage allowed*/
|
|
#define VDD_MV_MIN 775
|
|
#define VDD_MV_MAX 855
|
|
|
|
/* PM Bus commands code for LTC3882*/
|
|
#define PMBUS_CMD_PAGE 0x0
|
|
#define PMBUS_CMD_READ_VOUT 0x8B
|
|
#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
|
|
#define PMBUS_CMD_VOUT_COMMAND 0x21
|
|
#define PWM_CHANNEL0 0x0
|
|
|
|
#define CONFIG_VOL_MONITOR_LTC3882_SET
|
|
#define CONFIG_VOL_MONITOR_LTC3882_READ
|
|
|
|
/* RTC */
|
|
#define CONFIG_SYS_RTC_BUS_NUM 4
|
|
|
|
/* MAC/PHY configuration */
|
|
#if defined(CONFIG_FSL_MC_ENET)
|
|
#define CONFIG_MII
|
|
#define CONFIG_ETHPRIME "DPMAC1@xgmii"
|
|
|
|
#define AQR107_PHY_ADDR1 0x04
|
|
#define AQR107_PHY_ADDR2 0x05
|
|
#define AQR107_IRQ_MASK 0x0C
|
|
|
|
#define CORTINA_NO_FW_UPLOAD
|
|
#define CORTINA_PHY_ADDR1 0x0
|
|
#define INPHI_PHY_ADDR1 0x0
|
|
|
|
#define RGMII_PHY_ADDR1 0x01
|
|
#define RGMII_PHY_ADDR2 0x02
|
|
|
|
#endif
|
|
|
|
/* EMC2305 */
|
|
#define I2C_MUX_CH_EMC2305 0x09
|
|
#define I2C_EMC2305_ADDR 0x4D
|
|
#define I2C_EMC2305_CMD 0x40
|
|
#define I2C_EMC2305_PWM 0x80
|
|
|
|
/* EEPROM */
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
|
|
|
/* Initial environment variables */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
EXTRA_ENV_SETTINGS \
|
|
"lx2160ardb_vdd_mv=800\0" \
|
|
"BOARD=lx2160ardb\0" \
|
|
"xspi_bootcmd=echo Trying load from flexspi..;" \
|
|
"sf probe 0:0 && sf read $load_addr " \
|
|
"$kernel_start $kernel_size ; env exists secureboot &&" \
|
|
"sf read $kernelheader_addr_r $kernelheader_start " \
|
|
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
|
|
" bootm $load_addr#$BOARD\0" \
|
|
"sd_bootcmd=echo Trying load from sd card..;" \
|
|
"mmcinfo; mmc read $load_addr " \
|
|
"$kernel_addr_sd $kernel_size_sd ;" \
|
|
"env exists secureboot && mmc read $kernelheader_addr_r "\
|
|
"$kernelhdr_addr_sd $kernelhdr_size_sd " \
|
|
" && esbc_validate ${kernelheader_addr_r};" \
|
|
"bootm $load_addr#$BOARD\0"
|
|
|
|
#include <asm/fsl_secure_boot.h>
|
|
|
|
#endif /* __LX2_RDB_H */
|