mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-21 02:33:07 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
138 lines
2.5 KiB
C
138 lines
2.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2010, 2018
|
|
* Allied Telesis <www.alliedtelesis.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <led.h>
|
|
#include <asm/global_data.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/mpp.h>
|
|
#include <asm/arch/gpio.h>
|
|
|
|
#define SBX81LIFXCAT_OE_LOW (~0)
|
|
#define SBX81LIFXCAT_OE_HIGH (~BIT(11))
|
|
#define SBX81LIFXCAT_OE_VAL_LOW (0)
|
|
#define SBX81LIFXCAT_OE_VAL_HIGH (BIT(11))
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* default gpio configuration
|
|
* There are maximum 64 gpios controlled through 2 sets of registers
|
|
* the below configuration configures mainly initial LED status
|
|
*/
|
|
mvebu_config_gpio(SBX81LIFXCAT_OE_VAL_LOW,
|
|
SBX81LIFXCAT_OE_VAL_HIGH,
|
|
SBX81LIFXCAT_OE_LOW, SBX81LIFXCAT_OE_HIGH);
|
|
|
|
/* Multi-Purpose Pins Functionality configuration */
|
|
static const u32 kwmpp_config[] = {
|
|
MPP0_SPI_SCn,
|
|
MPP1_SPI_MOSI,
|
|
MPP2_SPI_SCK,
|
|
MPP3_SPI_MISO,
|
|
MPP4_NF_IO6,
|
|
MPP5_NF_IO7,
|
|
MPP6_SYSRST_OUTn,
|
|
MPP7_GPO,
|
|
MPP8_TW_SDA,
|
|
MPP9_TW_SCK,
|
|
MPP10_UART0_TXD,
|
|
MPP11_UART0_RXD,
|
|
MPP12_GPO,
|
|
MPP13_UART1_TXD,
|
|
MPP14_UART1_RXD,
|
|
MPP15_GPIO,
|
|
MPP16_GPIO,
|
|
MPP17_GPIO,
|
|
MPP18_NF_IO0,
|
|
MPP19_NF_IO1,
|
|
MPP20_GE1_0,
|
|
MPP21_GE1_1,
|
|
MPP22_GE1_2,
|
|
MPP23_GE1_3,
|
|
MPP24_GE1_4,
|
|
MPP25_GE1_5,
|
|
MPP26_GE1_6,
|
|
MPP27_GE1_7,
|
|
MPP28_GE1_8,
|
|
MPP29_GE1_9,
|
|
MPP30_GE1_10,
|
|
MPP31_GE1_11,
|
|
MPP32_GE1_12,
|
|
MPP33_GE1_13,
|
|
MPP34_GPIO,
|
|
MPP35_GPIO,
|
|
MPP36_GPIO,
|
|
MPP37_GPIO,
|
|
MPP38_GPIO,
|
|
MPP39_GPIO,
|
|
MPP40_GPIO,
|
|
MPP41_GPIO,
|
|
MPP42_GPIO,
|
|
MPP43_GPIO,
|
|
MPP44_GPIO,
|
|
MPP45_GPIO,
|
|
MPP46_GPIO,
|
|
MPP47_GPIO,
|
|
MPP48_GPIO,
|
|
MPP49_GPIO,
|
|
0
|
|
};
|
|
|
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* automatically defined by kirkwood config.h */
|
|
void reset_phy(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_MV88E61XX_SWITCH
|
|
int mv88e61xx_hw_reset(struct phy_device *phydev)
|
|
{
|
|
phydev->advertising = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full;
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_MISC_INIT_R
|
|
int misc_init_r(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
ret = led_get_by_label("status:ledp", &dev);
|
|
if (!ret)
|
|
led_set_state(dev, LEDST_ON);
|
|
|
|
ret = led_get_by_label("status:ledn", &dev);
|
|
if (!ret)
|
|
led_set_state(dev, LEDST_OFF);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|