mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-25 06:00:43 +00:00
93145335fb
The way that we use this file currently means that we have to guard it in every platform Kconfig. But it is also required in all NXP platforms, including non-reference platforms. Make all options in it have appropriate dependencies so that we can include it a single time under arch/Kconfig Signed-off-by: Tom Rini <trini@konsulko.com> |
||
|---|---|---|
| .. | ||
| eth.c | ||
| Kconfig | ||
| ls1012ardb.c | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Overview
--------
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LS1012A SoC Overview
--------------------
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
SoC overview.
LS1012ARDB board Overview
-----------------------
- SERDES Connections, 4 lanes supporting:
- PCI Express - 3.0
- SGMII, SGMII 2.5
- SATA 3.0
- DDR Controller
- 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
-QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
signals to
- QSPI NOR flash memory (2 virtual banks)
- the QSPI emulator.s
- USB 3.0
- one high-speed USB 2.0/3.0 port.
- Two enhanced secure digital host controllers:
- SDHC1 controller can be connected to onboard SDHC connector
- SDHC2 controller: Three dual 1:4 mux/demux devices,
74CBTLV3253DS (U30, U31, U33) drive the SDHC2 signals to eMMC,
SDIO WiFi, SPI, and Ardiuno shield
- 2 I2C controllers
- One SATA onboard connectors
- UART
- The LS1012A processor consists of two UART controllers,
out of which only UART1 is used on RDB.
- ARM JTAG support
Booting Options
---------------
a) QSPI Flash Emu Boot
b) QSPI Flash 1
c) QSPI Flash 2
QSPI flash map
--------------
Images | Size |QSPI Flash Address
------------------------------------------
RCW + PBI | 1MB | 0x4000_0000
U-boot | 1MB | 0x4010_0000
U-boot Env | 1MB | 0x4020_0000
PPA FIT image | 2MB | 0x4050_0000
Linux ITB | ~53MB | 0x40A0_0000
LS1012A2G5RDB board Overview
-----------------------
- SERDES Connections, 3 lanes supporting:
- SGMII, SGMII 2.5
- SATA 3.0
- DDR Controller
- 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
-QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
signals to
- QSPI NOR flash memory
- USB 3.0
- one high-speed USB 2.0/3.0 port.
- SDIO WiFi, SPI
- 2 I2C controllers
- One SATA onboard connectors
- UART
- The LS1012A processor consists of two UART controllers,
out of which only UART1 is used on 2G5RDB.
- ARM JTAG support
Major Difference between LS1012ARDB and LS1012A-2G5RDB
------------------------------------------------------
1. LS1012A-2G5RDB has Type C USB connector unlike USB Type A/B of LS1012ARDB
2. LS1012A-2G5RDB has 2 2.5G AQR PHY unlike 2 1G Realtek RTL8211FS PHYs
of LS1012ARDB
3. LS1012A-2G5RDB is not having Arduino header
4. LS1012A-2G5RDB doesn't have PCI slot
Booting Options
---------------
QSPI Flash
QSPI flash map
--------------
Images | Size |QSPI Flash Address
------------------------------------------
RCW + PBI | 1MB | 0x4000_0000
U-boot | 1MB | 0x4010_0000
U-boot Env | 1MB | 0x4030_0000
PPA FIT image | 2MB | 0x4040_0000
PFE firmware | 20K | 0x00a0_0000
Linux ITB | ~53MB | 0x4100_0000