u-boot/drivers/usb/musb-new/musb_core.h
Tom Rini 6e7df1d151 global: Finish CONFIG -> CFG migration
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks.  Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-01-20 12:27:24 -05:00

589 lines
15 KiB
C

/* SPDX-License-Identifier: GPL-2.0 */
/*
* MUSB OTG driver defines
*
* Copyright 2005 Mentor Graphics Corporation
* Copyright (C) 2005-2006 by Texas Instruments
* Copyright (C) 2006-2007 Nokia Corporation
*/
#ifndef __MUSB_CORE_H__
#define __MUSB_CORE_H__
#ifndef __UBOOT__
#include <linux/slab.h>
#include <linux/list.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/timer.h>
#include <linux/device.h>
#include <linux/usb.h>
#include <linux/usb/otg.h>
#else
#include <linux/errno.h>
#endif
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/musb.h>
struct musb;
struct musb_hw_ep;
struct musb_ep;
/* Helper defines for struct musb->hwvers */
#define MUSB_HWVERS_MAJOR(x) ((x >> 10) & 0x1f)
#define MUSB_HWVERS_MINOR(x) (x & 0x3ff)
#define MUSB_HWVERS_RC 0x8000
#define MUSB_HWVERS_1300 0x52C
#define MUSB_HWVERS_1400 0x590
#define MUSB_HWVERS_1800 0x720
#define MUSB_HWVERS_1900 0x784
#define MUSB_HWVERS_2000 0x800
#include "musb_debug.h"
#include "musb_dma.h"
#include "musb_io.h"
#include "musb_regs.h"
#include "musb_gadget.h"
#ifndef __UBOOT__
#include <linux/usb/hcd.h>
#endif
#include "musb_host.h"
#define is_peripheral_enabled(musb) ((musb)->board_mode != MUSB_HOST)
#define is_host_enabled(musb) ((musb)->board_mode != MUSB_PERIPHERAL)
#define is_otg_enabled(musb) ((musb)->board_mode == MUSB_OTG)
/* NOTE: otg and peripheral-only state machines start at B_IDLE.
* OTG or host-only go to A_IDLE when ID is sensed.
*/
#define is_peripheral_active(m) (!(m)->is_host)
#define is_host_active(m) ((m)->is_host)
#ifdef CONFIG_PROC_FS
#include <linux/fs.h>
#define MUSB_CONFIG_PROC_FS
#endif
/****************************** PERIPHERAL ROLE *****************************/
#ifndef __UBOOT__
#define is_peripheral_capable() (1)
#else
#ifdef CONFIG_USB_MUSB_GADGET
#define is_peripheral_capable() (1)
#else
#define is_peripheral_capable() (0)
#endif
#endif
extern irqreturn_t musb_g_ep0_irq(struct musb *);
extern void musb_g_tx(struct musb *, u8);
extern void musb_g_rx(struct musb *, u8);
extern void musb_g_reset(struct musb *);
extern void musb_g_suspend(struct musb *);
extern void musb_g_resume(struct musb *);
extern void musb_g_wakeup(struct musb *);
extern void musb_g_disconnect(struct musb *);
/****************************** HOST ROLE ***********************************/
#ifndef __UBOOT__
#define is_host_capable() (1)
#else
#ifdef CONFIG_USB_MUSB_HOST
#define is_host_capable() (1)
#else
#define is_host_capable() (0)
#endif
#endif
extern irqreturn_t musb_h_ep0_irq(struct musb *);
extern void musb_host_tx(struct musb *, u8);
extern void musb_host_rx(struct musb *, u8);
/****************************** CONSTANTS ********************************/
#ifndef MUSB_C_NUM_EPS
#define MUSB_C_NUM_EPS ((u8)16)
#endif
#ifndef MUSB_MAX_END0_PACKET
#define MUSB_MAX_END0_PACKET ((u16)MUSB_EP0_FIFOSIZE)
#endif
/* host side ep0 states */
enum musb_h_ep0_state {
MUSB_EP0_IDLE,
MUSB_EP0_START, /* expect ack of setup */
MUSB_EP0_IN, /* expect IN DATA */
MUSB_EP0_OUT, /* expect ack of OUT DATA */
MUSB_EP0_STATUS, /* expect ack of STATUS */
} __attribute__ ((packed));
/* peripheral side ep0 states */
enum musb_g_ep0_state {
MUSB_EP0_STAGE_IDLE, /* idle, waiting for SETUP */
MUSB_EP0_STAGE_SETUP, /* received SETUP */
MUSB_EP0_STAGE_TX, /* IN data */
MUSB_EP0_STAGE_RX, /* OUT data */
MUSB_EP0_STAGE_STATUSIN, /* (after OUT data) */
MUSB_EP0_STAGE_STATUSOUT, /* (after IN data) */
MUSB_EP0_STAGE_ACKWAIT, /* after zlp, before statusin */
} __attribute__ ((packed));
/*
* OTG protocol constants. See USB OTG 1.3 spec,
* sections 5.5 "Device Timings" and 6.6.5 "Timers".
*/
#define OTG_TIME_A_WAIT_VRISE 100 /* msec (max) */
#define OTG_TIME_A_WAIT_BCON 1100 /* min 1 second */
#define OTG_TIME_A_AIDL_BDIS 200 /* min 200 msec */
#define OTG_TIME_B_ASE0_BRST 100 /* min 3.125 ms */
/*************************** REGISTER ACCESS ********************************/
/* Endpoint registers (other than dynfifo setup) can be accessed either
* directly with the "flat" model, or after setting up an index register.
*/
#if defined(CONFIG_ARCH_DAVINCI) || defined(CONFIG_SOC_OMAP2430) \
|| defined(CFG_SOC_OMAP3430) || defined(CFG_ARCH_OMAP4)
/* REVISIT indexed access seemed to
* misbehave (on DaVinci) for at least peripheral IN ...
*/
#define MUSB_FLAT_REG
#endif
/* TUSB mapping: "flat" plus ep0 special cases */
#if defined(CONFIG_USB_MUSB_TUSB6010) || \
defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
#define musb_ep_select(_mbase, _epnum) \
musb_writeb((_mbase), MUSB_INDEX, (_epnum))
#define MUSB_EP_OFFSET MUSB_TUSB_OFFSET
/* "flat" mapping: each endpoint has its own i/o address */
#elif defined(MUSB_FLAT_REG)
#define musb_ep_select(_mbase, _epnum) (((void)(_mbase)), ((void)(_epnum)))
#define MUSB_EP_OFFSET MUSB_FLAT_OFFSET
/* "indexed" mapping: INDEX register controls register bank select */
#else
#define musb_ep_select(_mbase, _epnum) \
musb_writeb((_mbase), MUSB_INDEX, (_epnum))
#define MUSB_EP_OFFSET MUSB_INDEXED_OFFSET
#endif
/****************************** FUNCTIONS ********************************/
#define MUSB_HST_MODE(_musb)\
{ (_musb)->is_host = true; }
#define MUSB_DEV_MODE(_musb) \
{ (_musb)->is_host = false; }
#define test_devctl_hst_mode(_x) \
(musb_readb((_x)->mregs, MUSB_DEVCTL)&MUSB_DEVCTL_HM)
#define MUSB_MODE(musb) ((musb)->is_host ? "Host" : "Peripheral")
/******************************** TYPES *************************************/
/**
* struct musb_platform_ops - Operations passed to musb_core by HW glue layer
* @init: turns on clocks, sets up platform-specific registers, etc
* @exit: undoes @init
* @set_mode: forcefully changes operating mode
* @try_ilde: tries to idle the IP
* @vbus_status: returns vbus status if possible
* @set_vbus: forces vbus status
* @adjust_channel_params: pre check for standard dma channel_program func
* @pre_root_reset_end: called before the root usb port reset flag gets cleared
* @post_root_reset_end: called after the root usb port reset flag gets cleared
*/
struct musb_platform_ops {
int (*init)(struct musb *musb);
int (*exit)(struct musb *musb);
#ifndef __UBOOT__
void (*enable)(struct musb *musb);
#else
int (*enable)(struct musb *musb);
#endif
void (*disable)(struct musb *musb);
int (*set_mode)(struct musb *musb, u8 mode);
void (*try_idle)(struct musb *musb, unsigned long timeout);
int (*vbus_status)(struct musb *musb);
void (*set_vbus)(struct musb *musb, int on);
int (*adjust_channel_params)(struct dma_channel *channel,
u16 packet_sz, u8 *mode,
dma_addr_t *dma_addr, u32 *len);
void (*pre_root_reset_end)(struct musb *musb);
void (*post_root_reset_end)(struct musb *musb);
};
/*
* struct musb_hw_ep - endpoint hardware (bidirectional)
*
* Ordered slightly for better cacheline locality.
*/
struct musb_hw_ep {
struct musb *musb;
void __iomem *fifo;
void __iomem *regs;
#if defined(CONFIG_USB_MUSB_TUSB6010) || \
defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
void __iomem *conf;
#endif
/* index in musb->endpoints[] */
u8 epnum;
/* hardware configuration, possibly dynamic */
bool is_shared_fifo;
bool tx_double_buffered;
bool rx_double_buffered;
u16 max_packet_sz_tx;
u16 max_packet_sz_rx;
struct dma_channel *tx_channel;
struct dma_channel *rx_channel;
#if defined(CONFIG_USB_MUSB_TUSB6010) || \
defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
/* TUSB has "asynchronous" and "synchronous" dma modes */
dma_addr_t fifo_async;
dma_addr_t fifo_sync;
void __iomem *fifo_sync_va;
#endif
void __iomem *target_regs;
/* currently scheduled peripheral endpoint */
struct musb_qh *in_qh;
struct musb_qh *out_qh;
u8 rx_reinit;
u8 tx_reinit;
/* peripheral side */
struct musb_ep ep_in; /* TX */
struct musb_ep ep_out; /* RX */
};
static inline struct musb_request *next_in_request(struct musb_hw_ep *hw_ep)
{
return next_request(&hw_ep->ep_in);
}
static inline struct musb_request *next_out_request(struct musb_hw_ep *hw_ep)
{
return next_request(&hw_ep->ep_out);
}
struct musb_csr_regs {
/* FIFO registers */
u16 txmaxp, txcsr, rxmaxp, rxcsr;
u16 rxfifoadd, txfifoadd;
u8 txtype, txinterval, rxtype, rxinterval;
u8 rxfifosz, txfifosz;
u8 txfunaddr, txhubaddr, txhubport;
u8 rxfunaddr, rxhubaddr, rxhubport;
};
struct musb_context_registers {
u8 power;
u16 intrtxe, intrrxe;
u8 intrusbe;
u16 frame;
u8 index, testmode;
u8 devctl, busctl, misc;
u32 otg_interfsel;
struct musb_csr_regs index_regs[MUSB_C_NUM_EPS];
};
/*
* struct musb - Driver instance data.
*/
struct musb {
/* device lock */
spinlock_t lock;
const struct musb_platform_ops *ops;
struct musb_context_registers context;
irqreturn_t (*isr)(int, void *);
struct work_struct irq_work;
u16 hwvers;
/* this hub status bit is reserved by USB 2.0 and not seen by usbcore */
#define MUSB_PORT_STAT_RESUME (1 << 31)
u32 port1_status;
unsigned long rh_timer;
enum musb_h_ep0_state ep0_stage;
/* bulk traffic normally dedicates endpoint hardware, and each
* direction has its own ring of host side endpoints.
* we try to progress the transfer at the head of each endpoint's
* queue until it completes or NAKs too much; then we try the next
* endpoint.
*/
struct musb_hw_ep *bulk_ep;
struct list_head control; /* of musb_qh */
struct list_head in_bulk; /* of musb_qh */
struct list_head out_bulk; /* of musb_qh */
struct timer_list otg_timer;
struct notifier_block nb;
struct dma_controller *dma_controller;
struct device *controller;
void __iomem *ctrl_base;
void __iomem *mregs;
#if defined(CONFIG_USB_MUSB_TUSB6010) || \
defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
dma_addr_t async;
dma_addr_t sync;
void __iomem *sync_va;
#endif
/* passed down from chip/board specific irq handlers */
u8 int_usb;
u16 int_rx;
u16 int_tx;
struct usb_phy *xceiv;
int nIrq;
unsigned irq_wake:1;
struct musb_hw_ep endpoints[MUSB_C_NUM_EPS];
#define control_ep endpoints
#define VBUSERR_RETRY_COUNT 3
u16 vbuserr_retry;
u16 epmask;
u8 nr_endpoints;
u8 board_mode; /* enum musb_mode */
int (*board_set_power)(int state);
u8 min_power; /* vbus for periph, in mA/2 */
bool is_host;
int a_wait_bcon; /* VBUS timeout in msecs */
unsigned long idle_timeout; /* Next timeout in jiffies */
/* active means connected and not suspended */
unsigned is_active:1;
unsigned is_multipoint:1;
unsigned ignore_disconnect:1; /* during bus resets */
unsigned hb_iso_rx:1; /* high bandwidth iso rx? */
unsigned hb_iso_tx:1; /* high bandwidth iso tx? */
unsigned dyn_fifo:1; /* dynamic FIFO supported? */
unsigned bulk_split:1;
#define can_bulk_split(musb,type) \
(((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_split)
unsigned bulk_combine:1;
#define can_bulk_combine(musb,type) \
(((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_combine)
/* is_suspended means USB B_PERIPHERAL suspend */
unsigned is_suspended:1;
/* may_wakeup means remote wakeup is enabled */
unsigned may_wakeup:1;
/* is_self_powered is reported in device status and the
* config descriptor. is_bus_powered means B_PERIPHERAL
* draws some VBUS current; both can be true.
*/
unsigned is_self_powered:1;
unsigned is_bus_powered:1;
unsigned set_address:1;
unsigned test_mode:1;
unsigned softconnect:1;
u8 address;
u8 test_mode_nr;
u16 ackpend; /* ep0 */
enum musb_g_ep0_state ep0_state;
struct usb_gadget g; /* the gadget */
struct usb_gadget_driver *gadget_driver; /* its driver */
/*
* FIXME: Remove this flag.
*
* This is only added to allow Blackfin to work
* with current driver. For some unknown reason
* Blackfin doesn't work with double buffering
* and that's enabled by default.
*
* We added this flag to forcefully disable double
* buffering until we get it working.
*/
unsigned double_buffer_not_ok:1;
struct musb_hdrc_config *config;
#ifdef MUSB_CONFIG_PROC_FS
struct proc_dir_entry *proc_entry;
#endif
};
static inline struct musb *gadget_to_musb(struct usb_gadget *g)
{
return container_of(g, struct musb, g);
}
static inline int musb_read_fifosize(struct musb *musb,
struct musb_hw_ep *hw_ep, u8 epnum)
{
void *mbase = musb->mregs;
u8 reg = 0;
/* read from core using indexed model */
reg = musb_readb(mbase, MUSB_EP_OFFSET(epnum, MUSB_FIFOSIZE));
/* 0's returned when no more endpoints */
if (!reg)
return -ENODEV;
musb->nr_endpoints++;
musb->epmask |= (1 << epnum);
hw_ep->max_packet_sz_tx = 1 << (reg & 0x0f);
/* shared TX/RX FIFO? */
if ((reg & 0xf0) == 0xf0) {
hw_ep->max_packet_sz_rx = hw_ep->max_packet_sz_tx;
hw_ep->is_shared_fifo = true;
return 0;
} else {
hw_ep->max_packet_sz_rx = 1 << ((reg & 0xf0) >> 4);
hw_ep->is_shared_fifo = false;
}
return 0;
}
static inline void musb_configure_ep0(struct musb *musb)
{
musb->endpoints[0].max_packet_sz_tx = MUSB_EP0_FIFOSIZE;
musb->endpoints[0].max_packet_sz_rx = MUSB_EP0_FIFOSIZE;
musb->endpoints[0].is_shared_fifo = true;
}
/***************************** Glue it together *****************************/
extern const char musb_driver_name[];
#ifndef __UBOOT__
extern void musb_start(struct musb *musb);
#else
extern int musb_start(struct musb *musb);
#endif
extern void musb_stop(struct musb *musb);
extern void musb_write_fifo(struct musb_hw_ep *ep, u16 len, const u8 *src);
extern void musb_read_fifo(struct musb_hw_ep *ep, u16 len, u8 *dst);
extern void musb_load_testpacket(struct musb *);
extern irqreturn_t musb_interrupt(struct musb *);
extern void musb_hnp_stop(struct musb *musb);
static inline void musb_platform_set_vbus(struct musb *musb, int is_on)
{
if (musb->ops->set_vbus)
musb->ops->set_vbus(musb, is_on);
}
#ifndef __UBOOT__
static inline void musb_platform_enable(struct musb *musb)
{
if (musb->ops->enable)
musb->ops->enable(musb);
}
#else
static inline int musb_platform_enable(struct musb *musb)
{
if (!musb->ops->enable)
return 0;
return musb->ops->enable(musb);
}
#endif
static inline void musb_platform_disable(struct musb *musb)
{
if (musb->ops->disable)
musb->ops->disable(musb);
}
static inline int musb_platform_set_mode(struct musb *musb, u8 mode)
{
if (!musb->ops->set_mode)
return 0;
return musb->ops->set_mode(musb, mode);
}
static inline void musb_platform_try_idle(struct musb *musb,
unsigned long timeout)
{
if (musb->ops->try_idle)
musb->ops->try_idle(musb, timeout);
}
static inline int musb_platform_get_vbus_status(struct musb *musb)
{
if (!musb->ops->vbus_status)
return 0;
return musb->ops->vbus_status(musb);
}
static inline int musb_platform_init(struct musb *musb)
{
if (!musb->ops->init)
return -EINVAL;
return musb->ops->init(musb);
}
static inline int musb_platform_exit(struct musb *musb)
{
if (!musb->ops->exit)
return -EINVAL;
return musb->ops->exit(musb);
}
#ifdef __UBOOT__
struct musb *
musb_init_controller(struct musb_hdrc_platform_data *plat, struct device *dev,
void *ctrl);
#endif
#endif /* __MUSB_CORE_H__ */