u-boot/board/freescale/ls1043ardb/eth.c
Vladimir Oltean 77b11f7604 net: replace the "xfi" phy-mode with "10gbase-r"
As part of the effort of making U-Boot work with the same device tree as
Linux, there is an issue with the "xfi" phy-mode. To be precise, in
Linux there was a discussion (for those who have time to read:
https://lore.kernel.org/netdev/1576768881-24971-2-git-send-email-madalin.bucur@oss.nxp.com/)

which led to a patch:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c114574ebfdf42f826776f717c8056a00fa94881

TL;DR: "xfi" was standardized in Linux as "10gbase-r".

This patch changes the relevant occurrences in U-Boot to use "10gbase-r"
instead of "xfi" wherever applicable.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-28 18:50:56 +03:00

77 lines
2 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <net.h>
#include <asm/io.h>
#include <netdev.h>
#include <fm_eth.h>
#include <fsl_dtsec.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include "../common/fman.h"
int board_eth_init(struct bd_info *bis)
{
#ifdef CONFIG_FMAN_ENET
int i;
struct memac_mdio_info dtsec_mdio_info;
struct memac_mdio_info tgec_mdio_info;
struct mii_dev *dev;
u32 srds_s1;
struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
srds_s1 = in_be32(&gur->rcwsr[4]) &
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
dtsec_mdio_info.regs =
(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
/* Register the 1G MDIO bus */
fm_memac_mdio_init(bis, &dtsec_mdio_info);
tgec_mdio_info.regs =
(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
/* Register the 10G MDIO bus */
fm_memac_mdio_init(bis, &tgec_mdio_info);
/* Set the two on-board RGMII PHY address */
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
/* QSGMII on lane B, MAC 1/2/5/6 */
fm_info_set_phy_address(FM1_DTSEC1, QSGMII_PORT1_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2, QSGMII_PORT2_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC5, QSGMII_PORT3_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, QSGMII_PORT4_PHY_ADDR);
switch (srds_s1) {
case 0x1455:
break;
default:
printf("Invalid SerDes protocol 0x%x for LS1043ARDB\n",
srds_s1);
break;
}
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
fm_info_set_mdio(i, dev);
/* 10GBase-R on lane A, MAC 9 */
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
fm_info_set_mdio(FM1_10GEC1, dev);
cpu_eth_init(bis);
#endif
return pci_eth_init(bis);
}