mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 08:31:03 +00:00
c05ed00afb
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
352 lines
9.7 KiB
C
352 lines
9.7 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015-2019 Stefan Roese <sr@denx.de>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <console.h>
|
|
#include <i2c.h>
|
|
#include <init.h>
|
|
#include <net.h>
|
|
#include <pci.h>
|
|
#if !defined(CONFIG_SPL_BUILD)
|
|
#include <bootcount.h>
|
|
#endif
|
|
#include <asm/gpio.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/mbus.h>
|
|
#ifdef CONFIG_NET
|
|
#include <netdev.h>
|
|
#endif
|
|
#include <u-boot/crc.h>
|
|
#include "theadorable.h"
|
|
|
|
#include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
|
|
#include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define MV_USB_PHY_BASE (MVEBU_AXP_USB_BASE + 0x800)
|
|
#define PHY_CHANNEL_RX_CTRL0_REG(port, chan) \
|
|
(MV_USB_PHY_BASE + ((port) << 12) + ((chan) << 6) + 0x8)
|
|
|
|
#define THEADORABLE_GPP_OUT_ENA_LOW 0x00336780
|
|
#define THEADORABLE_GPP_OUT_ENA_MID 0x00003cf0
|
|
#define THEADORABLE_GPP_OUT_ENA_HIGH (~(0x0))
|
|
|
|
#define THEADORABLE_GPP_OUT_VAL_LOW 0x2c0c983f
|
|
#define THEADORABLE_GPP_OUT_VAL_MID 0x0007000c
|
|
#define THEADORABLE_GPP_OUT_VAL_HIGH 0x00000000
|
|
|
|
#define GPIO_USB0_PWR_ON 18
|
|
#define GPIO_USB1_PWR_ON 19
|
|
|
|
#define PEX_SWITCH_NOT_FOUNT_LIMIT 3
|
|
|
|
#define STM_I2C_BUS 1
|
|
#define STM_I2C_ADDR 0x27
|
|
#define REBOOT_DELAY 1000 /* reboot-delay in ms */
|
|
#define ABORT_TIMEOUT 3000 /* 3 seconds reboot abort timeout */
|
|
|
|
/* DDR3 static configuration */
|
|
static MV_DRAM_MC_INIT ddr3_theadorable[MV_MAX_DDR3_STATIC_SIZE] = {
|
|
{0x00001400, 0x7301ca28}, /* DDR SDRAM Configuration Register */
|
|
{0x00001404, 0x30000800}, /* Dunit Control Low Register */
|
|
{0x00001408, 0x44149887}, /* DDR SDRAM Timing (Low) Register */
|
|
{0x0000140C, 0x38d93fc7}, /* DDR SDRAM Timing (High) Register */
|
|
{0x00001410, 0x1b100001}, /* DDR SDRAM Address Control Register */
|
|
{0x00001424, 0x0000f3ff}, /* Dunit Control High Register */
|
|
{0x00001428, 0x000f8830}, /* ODT Timing (Low) Register */
|
|
{0x0000142C, 0x014c50f4}, /* DDR3 Timing Register */
|
|
{0x0000147C, 0x0000c671}, /* ODT Timing (High) Register */
|
|
|
|
{0x00001494, 0x00010000}, /* DDR SDRAM ODT Control (Low) Reg */
|
|
{0x0000149C, 0x00000001}, /* DDR Dunit ODT Control Register */
|
|
{0x000014A0, 0x00000001}, /* DRAM FIFO Control Register */
|
|
{0x000014A8, 0x00000101}, /* AXI Control Register */
|
|
|
|
/*
|
|
* DO NOT Modify - Open Mbus Window - 2G - Mbus is required for the
|
|
* training sequence
|
|
*/
|
|
{0x000200e8, 0x3fff0e01},
|
|
{0x00020184, 0x3fffffe0}, /* Close fast path Window to - 2G */
|
|
|
|
{0x0001504, 0x7fffffe1}, /* CS0 Size */
|
|
{0x000150C, 0x00000000}, /* CS1 Size */
|
|
{0x0001514, 0x00000000}, /* CS2 Size */
|
|
{0x000151C, 0x00000000}, /* CS3 Size */
|
|
|
|
{0x00020220, 0x00000007}, /* Reserved */
|
|
|
|
{0x00001538, 0x00000009}, /* Read Data Sample Delays Register */
|
|
{0x0000153C, 0x00000009}, /* Read Data Ready Delay Register */
|
|
|
|
{0x000015D0, 0x00000650}, /* MR0 */
|
|
{0x000015D4, 0x00000044}, /* MR1 */
|
|
{0x000015D8, 0x00000010}, /* MR2 */
|
|
{0x000015DC, 0x00000000}, /* MR3 */
|
|
{0x000015E0, 0x00000001},
|
|
{0x000015E4, 0x00203c18}, /* ZQDS Configuration Register */
|
|
{0x000015EC, 0xf800a225}, /* DDR PHY */
|
|
|
|
/* Recommended Settings from Marvell for 4 x 16 bit devices: */
|
|
{0x000014C0, 0x192424c9}, /* DRAM addr and Ctrl Driving Strenght*/
|
|
{0x000014C4, 0x0aaa24c9}, /* DRAM Data and DQS Driving Strenght */
|
|
|
|
{0x0, 0x0}
|
|
};
|
|
|
|
static MV_DRAM_MODES board_ddr_modes[MV_DDR3_MODES_NUMBER] = {
|
|
{"theadorable_1333-667", 0x3, 0x5, 0x0, A0, ddr3_theadorable, NULL},
|
|
};
|
|
|
|
extern MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[];
|
|
|
|
/*
|
|
* Lane0 - PCIE0.0 X1 (to WIFI Module)
|
|
* Lane5 - SATA0
|
|
* Lane6 - SATA1
|
|
* Lane7 - SGMII0 (to Ethernet Phy)
|
|
* Lane8-11 - PCIE2.0 X4 (to PEX Switch)
|
|
* all other lanes are disabled
|
|
*/
|
|
MV_BIN_SERDES_CFG theadorable_serdes_cfg[] = {
|
|
{ MV_PEX_ROOT_COMPLEX, 0x22200001, 0x00001111,
|
|
{ PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4,
|
|
PEX_BUS_DISABLED },
|
|
0x0060, serdes_change_m_phy
|
|
},
|
|
};
|
|
|
|
/*
|
|
* Define a board-specific detection pulse-width array for the SerDes PCIe
|
|
* interfaces. If not defined in the board code, the default of currently 2
|
|
* is used. Values from 0...3 are possible (2 bits).
|
|
*/
|
|
u8 serdes_pex_pulse_width[4] = { 0, 2, 2, 2 };
|
|
|
|
MV_DRAM_MODES *ddr3_get_static_ddr_mode(void)
|
|
{
|
|
/* Only one mode supported for this board */
|
|
return &board_ddr_modes[0];
|
|
}
|
|
|
|
MV_BIN_SERDES_CFG *board_serdes_cfg_get(void)
|
|
{
|
|
return &theadorable_serdes_cfg[0];
|
|
}
|
|
|
|
u8 board_sat_r_get(u8 dev_num, u8 reg)
|
|
{
|
|
/* Bit x enables PCI 2.0 link capabilities instead of PCI 1.x */
|
|
return 0xe; /* PEX port 0 is PCIe Gen1, PEX port 1..3 PCIe Gen2 */
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* Configure MPP */
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x00);
|
|
writel(0x03300000, MVEBU_MPP_BASE + 0x04);
|
|
writel(0x00000033, MVEBU_MPP_BASE + 0x08);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x0c);
|
|
writel(0x11110000, MVEBU_MPP_BASE + 0x10);
|
|
writel(0x00221100, MVEBU_MPP_BASE + 0x14);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x18);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x1c);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x20);
|
|
|
|
/* Configure GPIO */
|
|
writel(THEADORABLE_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
|
|
writel(THEADORABLE_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
|
|
writel(THEADORABLE_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
|
|
writel(THEADORABLE_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
|
|
writel(THEADORABLE_GPP_OUT_VAL_HIGH, MVEBU_GPIO2_BASE + 0x00);
|
|
writel(THEADORABLE_GPP_OUT_ENA_HIGH, MVEBU_GPIO2_BASE + 0x04);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
int ret;
|
|
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
/*
|
|
* Map SPI devices via MBUS so that they can be accessed via
|
|
* the SPI direct access mode
|
|
*/
|
|
mbus_dt_setup_win(&mbus_state, SPI_BUS0_DEV1_BASE, SPI_BUS0_DEV1_SIZE,
|
|
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI0_CS1);
|
|
mbus_dt_setup_win(&mbus_state, SPI_BUS1_DEV2_BASE, SPI_BUS0_DEV1_SIZE,
|
|
CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI1_CS2);
|
|
|
|
/*
|
|
* Set RX Channel Control 0 Register:
|
|
* Tests have shown, that setting the LPF_COEF from 0 (1/8)
|
|
* to 3 (1/1) results in a more stable USB connection.
|
|
*/
|
|
setbits_le32(PHY_CHANNEL_RX_CTRL0_REG(0, 1), 0xc);
|
|
setbits_le32(PHY_CHANNEL_RX_CTRL0_REG(0, 2), 0xc);
|
|
setbits_le32(PHY_CHANNEL_RX_CTRL0_REG(0, 3), 0xc);
|
|
|
|
/* Toggle USB power */
|
|
ret = gpio_request(GPIO_USB0_PWR_ON, "USB0_PWR_ON");
|
|
if (ret < 0)
|
|
return ret;
|
|
gpio_direction_output(GPIO_USB0_PWR_ON, 0);
|
|
ret = gpio_request(GPIO_USB1_PWR_ON, "USB1_PWR_ON");
|
|
if (ret < 0)
|
|
return ret;
|
|
gpio_direction_output(GPIO_USB1_PWR_ON, 0);
|
|
mdelay(1);
|
|
gpio_set_value(GPIO_USB0_PWR_ON, 1);
|
|
gpio_set_value(GPIO_USB1_PWR_ON, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
board_fpga_add();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_NET
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
cpu_eth_init(bis); /* Built in controller(s) come first */
|
|
return pci_eth_init(bis);
|
|
}
|
|
#endif
|
|
|
|
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_BOARD_LATE_INIT)
|
|
int board_late_init(void)
|
|
{
|
|
pci_dev_t bdf;
|
|
ulong bootcount;
|
|
|
|
/*
|
|
* Check if the PEX switch is detected (somtimes its not available
|
|
* on the PCIe bus). In this case, try to recover by issuing a
|
|
* soft-reset or even a power-cycle, depending on the bootcounter
|
|
* value.
|
|
*/
|
|
bdf = pci_find_device(PCI_VENDOR_ID_PLX, 0x8619, 0);
|
|
if (bdf == -1) {
|
|
unsigned long start_time = get_timer(0);
|
|
u8 i2c_buf[8];
|
|
int ret;
|
|
|
|
/* PEX switch not found! */
|
|
bootcount = bootcount_load();
|
|
printf("Failed to find PLX PEX-switch (bootcount=%ld)\n",
|
|
bootcount);
|
|
|
|
/*
|
|
* The user can exit this boot-loop in the error case by
|
|
* hitting Ctrl-C. So wait some time for this key here.
|
|
*/
|
|
printf("Continue booting with Ctrl-C, otherwise rebooting\n");
|
|
do {
|
|
/* Handle control-c and timeouts */
|
|
if (ctrlc()) {
|
|
printf("PEX error boot-loop aborted!\n");
|
|
return 0;
|
|
}
|
|
} while (get_timer(start_time) < ABORT_TIMEOUT);
|
|
|
|
|
|
/*
|
|
* At this stage the bootcounter has not been incremented
|
|
* yet. We need to do this manually here to get an actually
|
|
* working bootcounter in this error case.
|
|
*/
|
|
bootcount_inc();
|
|
|
|
if (bootcount > PEX_SWITCH_NOT_FOUNT_LIMIT) {
|
|
printf("Issuing power-switch via uC!\n");
|
|
|
|
printf("Issuing power-switch via uC!\n");
|
|
i2c_set_bus_num(STM_I2C_BUS);
|
|
i2c_buf[0] = STM_I2C_ADDR << 1;
|
|
i2c_buf[1] = 0xc5; /* cmd */
|
|
i2c_buf[2] = 0x01; /* enable */
|
|
/* Delay before reboot */
|
|
i2c_buf[3] = REBOOT_DELAY & 0x00ff;
|
|
i2c_buf[4] = (REBOOT_DELAY & 0xff00) >> 8;
|
|
/* Delay before shutdown */
|
|
i2c_buf[5] = 0x00;
|
|
i2c_buf[6] = 0x00;
|
|
i2c_buf[7] = crc8(0x72, &i2c_buf[0], 7);
|
|
|
|
ret = i2c_write(STM_I2C_ADDR, 0, 0, &i2c_buf[1], 7);
|
|
if (ret) {
|
|
printf("I2C write error (ret=%d)\n", ret);
|
|
printf("Issuing soft-reset...\n");
|
|
/* default handling: SOFT reset */
|
|
do_reset(NULL, 0, 0, NULL);
|
|
}
|
|
|
|
/* Wait for power-cycle to occur... */
|
|
printf("Waiting for power-cycle via uC...\n");
|
|
while (1)
|
|
;
|
|
} else {
|
|
printf("Issuing soft-reset...\n");
|
|
/* default handling: SOFT reset */
|
|
do_reset(NULL, 0, 0, NULL);
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_PCI)
|
|
int do_pcie_test(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
|
|
{
|
|
pci_dev_t bdf;
|
|
u16 ven_id, dev_id;
|
|
|
|
if (argc != 3)
|
|
return cmd_usage(cmdtp);
|
|
|
|
ven_id = simple_strtoul(argv[1], NULL, 16);
|
|
dev_id = simple_strtoul(argv[2], NULL, 16);
|
|
|
|
printf("Checking for PCIe device: VendorID 0x%04x, DeviceId 0x%04x\n",
|
|
ven_id, dev_id);
|
|
|
|
/*
|
|
* Check if the PCIe device is detected (somtimes its not available
|
|
* on the PCIe bus)
|
|
*/
|
|
bdf = pci_find_device(ven_id, dev_id, 0);
|
|
if (bdf == -1) {
|
|
/* PCIe device not found! */
|
|
printf("Failed to find PCIe device\n");
|
|
} else {
|
|
/* PCIe device found! */
|
|
printf("PCIe device found, resetting board...\n");
|
|
|
|
/* default handling: SOFT reset */
|
|
do_reset(NULL, 0, 0, NULL);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
U_BOOT_CMD(
|
|
pcie, 3, 0, do_pcie_test,
|
|
"Test for presence of a PCIe device",
|
|
"<VendorID> <DeviceID>"
|
|
);
|
|
#endif
|