u-boot/include/configs/imx27lite-common.h
Tom Rini eaf6ea6a1d Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
  pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
  set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
  GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
  board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:19 -04:00

140 lines
3.5 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2010 Heiko Schocher <hs@denx.de>
*
* based on:
* Copyright (C) 2009 Ilya Yanok <yanok@emcraft.com>
*/
#ifndef __IMX27LITE_COMMON_CONFIG_H
#define __IMX27LITE_COMMON_CONFIG_H
/*
* SoC Configuration
*/
#define CONFIG_MX27
#define CONFIG_MX27_CLK32 32768 /* OSC32K frequency */
/*
* Lowlevel configuration
*/
#define SDRAM_ESDCFG_REGISTER_VAL(cas) \
(ESDCFG_TRC(10) | \
ESDCFG_TRCD(3) | \
ESDCFG_TCAS(cas) | \
ESDCFG_TRRD(1) | \
ESDCFG_TRAS(5) | \
ESDCFG_TWR | \
ESDCFG_TMRD(2) | \
ESDCFG_TRP(2) | \
ESDCFG_TXP(3))
#define SDRAM_ESDCTL_REGISTER_VAL \
(ESDCTL_PRCT(0) | \
ESDCTL_BL | \
ESDCTL_PWDT(0) | \
ESDCTL_SREFR(3) | \
ESDCTL_DSIZ_32 | \
ESDCTL_COL10 | \
ESDCTL_ROW13 | \
ESDCTL_SDE)
#define SDRAM_ALL_VAL 0xf00
#define SDRAM_MODE_REGISTER_VAL 0x33 /* BL: 8, CAS: 3 */
#define SDRAM_EXT_MODE_REGISTER_VAL 0x1000000
#define MPCTL0_VAL 0x1ef15d5
#define SPCTL0_VAL 0x043a1c09
#define CSCR_VAL 0x33f08107
#define PCDR0_VAL 0x120470c3
#define PCDR1_VAL 0x03030303
#define PCCR0_VAL 0xffffffff
#define PCCR1_VAL 0xfffffffc
#define AIPI1_PSR0_VAL 0x20040304
#define AIPI1_PSR1_VAL 0xdffbfcfb
#define AIPI2_PSR0_VAL 0x07ffc200
#define AIPI2_PSR1_VAL 0xffffffff
/*
* Memory Info
*/
/* memtest start address */
#define PHYS_SDRAM_1 0xA0000000 /* DDR Start */
#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
/*
* Serial Driver info
*/
#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(1)
/*
* Flash & Environment
*/
/* Use buffered writes (~10x faster) */
/* Use hardware sector protection */
/* CS2 Base address */
#define PHYS_FLASH_1 0xc0000000
/* Flash Base for U-Boot */
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE / \
CONFIG_SYS_FLASH_SECT_SZ)
#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256KiB */
/* Address and size of Redundant Environment Sector */
/*
* Ethernet
*/
#define CONFIG_FEC_MXC_PHYADDR 0x1f
/*
* MTD
*/
/*
* NAND
*/
#define CONFIG_MXC_NAND_REGS_BASE 0xd8000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0xd8000000
#define CONFIG_MXC_NAND_HWECC
/*
* U-Boot general configuration
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs}" \
" console=ttymxc0,${baudrate}\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addmisc=setenv bootargs ${bootargs}\0" \
"u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \
"kernel_addr_r=a0800000\0" \
"bootfile=" CONFIG_HOSTNAME "/uImage\0" \
"rootpath=/opt/eldk-4.2-arm/arm\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
"run nfsargs addip addtty addmtd addmisc;" \
"bootm\0" \
"bootcmd=run net_nfs\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
" +${filesize};cp.b ${fileaddr} " \
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
"upd=run load update\0" \
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#endif /* __IMX27LITE_COMMON_CONFIG_H */