u-boot/arch/x86/cpu/start.S
Simon Glass 401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00

316 lines
7.6 KiB
ArmAsm

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* U-Boot - x86 Startup Code
*
* This is always the first code to run from the U-Boot source. To spell it out:
*
* 1. When TPL (Tertiary Program Loader) is enabled, the boot flow is
* TPL->SPL->U-Boot and this file is used for TPL. Then start_from_tpl.S is used
* for SPL and start_from_spl.S is used for U-Boot proper.
*
* 2. When SPL (Secondary Program Loader) is enabled, but not TPL, the boot
* flow is SPL->U-Boot and this file is used for SPL. Then start_from_spl.S is
* used for U-Boot proper.
*
* 3. When neither TPL nor SPL is used, this file is used for U-Boot proper.
*
* (C) Copyright 2008-2011
* Graeme Russ, <graeme.russ@gmail.com>
*
* (C) Copyright 2002
* Daniel Engström, Omicron Ceti AB, <daniel@omicron.se>
*/
#include <config.h>
#include <asm/post.h>
#include <asm/processor.h>
#include <asm/processor-flags.h>
#include <generated/generic-asm-offsets.h>
#include <generated/asm-offsets.h>
#include <linux/linkage.h>
.section .text.start
.code32
.globl _start
.type _start, @function
.globl _x86boot_start
_x86boot_start:
/*
* This is the fail-safe 32-bit bootstrap entry point.
*
* This code is used when booting from another boot loader like
* coreboot or EFI. So we repeat some of the same init found in
* start16.
*/
cli
cld
/* Turn off cache (this might require a 486-class CPU) */
movl %cr0, %eax
orl $(X86_CR0_NW | X86_CR0_CD), %eax
movl %eax, %cr0
wbinvd
/*
* Zero the BIST (Built-In Self Test) value since we don't have it.
* It must be 0 or the previous loader would have reported an error.
*/
movl $0, %ebp
jmp 1f
/* Add a way for tools to discover the _start entry point */
.align 4
.long 0x12345678
_start:
/* This is the 32-bit cold-reset entry point, coming from start16 */
/* Save BIST */
movl %eax, %ebp
1:
/* Save table pointer */
movl %ecx, %esi
#ifdef CONFIG_X86_LOAD_FROM_32_BIT
lgdt gdt_ptr2
#endif
/* Load the segment registers to match the GDT loaded in start16.S */
movl $(X86_GDT_ENTRY_32BIT_DS * X86_GDT_ENTRY_SIZE), %eax
movw %ax, %fs
movw %ax, %ds
movw %ax, %gs
movw %ax, %es
movw %ax, %ss
/* Clear the interrupt vectors */
lidt blank_idt_ptr
#ifdef CONFIG_USE_EARLY_BOARD_INIT
/*
* Critical early platform init - generally not used, we prefer init
* to happen later when we have a console, in case something goes
* wrong.
*/
jmp early_board_init
.globl early_board_init_ret
early_board_init_ret:
#endif
post_code(POST_START)
/* Initialise Cache-As-RAM */
jmp car_init
.globl car_init_ret
car_init_ret:
#ifdef CONFIG_USE_CAR
/*
* We now have CONFIG_SYS_CAR_SIZE bytes of Cache-As-RAM (or SRAM,
* or fully initialised SDRAM - we really don't care which)
* starting at CONFIG_SYS_CAR_ADDR to be used as a temporary stack
* and early malloc() area. The MRC requires some space at the top.
*
* Stack grows down from top of CAR. We have:
*
* top-> CONFIG_SYS_CAR_ADDR + CONFIG_SYS_CAR_SIZE
* MRC area
* global_data with x86 global descriptor table
* early malloc area
* stack
* bottom-> CONFIG_SYS_CAR_ADDR
*/
movl $(CONFIG_SYS_CAR_ADDR + CONFIG_SYS_CAR_SIZE - 4), %esp
#ifdef CONFIG_DCACHE_RAM_MRC_VAR_SIZE
subl $CONFIG_DCACHE_RAM_MRC_VAR_SIZE, %esp
#endif
#else
/*
* Instructions for FSP1, but not FSP2:
* U-Boot enters here twice. For the first time it comes from
* car_init_done() with esp points to a temporary stack and esi
* set to zero. For the second time it comes from fsp_init_done()
* with esi holding the HOB list address returned by the FSP.
*/
#endif
/* Set up global data */
mov %esp, %eax
call board_init_f_alloc_reserve
mov %eax, %esp
call board_init_f_init_reserve
#ifdef CONFIG_DEBUG_UART
call debug_uart_init
#endif
/* Get address of global_data */
mov %fs:0, %edx
#if defined(CONFIG_USE_HOB) && !defined(CONFIG_USE_CAR)
/* Store the HOB list if we have one */
test %esi, %esi
jz skip_hob
movl %esi, GD_HOB_LIST(%edx)
#ifdef CONFIG_HAVE_FSP
/*
* After fsp_init() returns, the stack has already been switched to a
* place within system memory as defined by CONFIG_FSP_TEMP_RAM_ADDR.
* Enlarge the size of malloc() pool before relocation since we have
* plenty of memory now.
*/
subl $CONFIG_FSP_SYS_MALLOC_F_LEN, %esp
movl %esp, GD_MALLOC_BASE(%edx)
#endif
skip_hob:
#else
/* Store table pointer */
movl %esi, GD_TABLE(%edx)
#endif
/* Store BIST */
movl %ebp, GD_BIST(%edx)
/* Set parameter to board_init_f() to boot flags */
post_code(POST_START_DONE)
xorl %eax, %eax
/* Enter, U-Boot! */
call board_init_f
/* indicate (lack of) progress */
movw $0x85, %ax
jmp die
.globl board_init_f_r_trampoline
.type board_init_f_r_trampoline, @function
board_init_f_r_trampoline:
/*
* SDRAM has been initialised, U-Boot code has been copied into
* RAM, BSS has been cleared and relocation adjustments have been
* made. It is now time to jump into the in-RAM copy of U-Boot
*
* %eax = Address of top of new stack
*/
/* Stack grows down from top of SDRAM */
movl %eax, %esp
/* See if we need to disable CAR */
call car_uninit
/* Re-enter U-Boot by calling board_init_f_r() */
call board_init_f_r
#ifdef CONFIG_TPL
.globl jump_to_spl
.type jump_to_spl, @function
jump_to_spl:
/* Reset stack to the top of CAR space */
movl $(CONFIG_SYS_CAR_ADDR + CONFIG_SYS_CAR_SIZE - 4), %esp
#ifdef CONFIG_DCACHE_RAM_MRC_VAR_SIZE
subl $CONFIG_DCACHE_RAM_MRC_VAR_SIZE, %esp
#endif
jmp *%eax
#endif
die:
hlt
jmp die
hlt
WEAK(car_uninit)
ret
ENDPROC(car_uninit)
blank_idt_ptr:
.word 0 /* limit */
.long 0 /* base */
.p2align 2 /* force 4-byte alignment */
/* Add a multiboot header so U-Boot can be loaded by GRUB2 */
multiboot_header:
/* magic */
.long 0x1badb002
/* flags */
.long (1 << 16)
/* checksum */
.long -0x1BADB002 - (1 << 16)
/* header addr */
.long multiboot_header - _x86boot_start + CONFIG_SYS_TEXT_BASE
/* load addr */
.long CONFIG_SYS_TEXT_BASE
/* load end addr */
.long 0
/* bss end addr */
.long 0
/* entry addr */
.long CONFIG_SYS_TEXT_BASE
#ifdef CONFIG_X86_LOAD_FROM_32_BIT
/*
* The following Global Descriptor Table is just enough to get us into
* 'Flat Protected Mode' - It will be discarded as soon as the final
* GDT is setup in a safe location in RAM
*/
gdt_ptr2:
.word 0x1f /* limit (31 bytes = 4 GDT entries - 1) */
.long gdt_rom2 /* base */
/* Some CPUs are picky about GDT alignment... */
.align 16
.globl gdt_rom2
gdt_rom2:
/*
* The GDT table ...
*
* Selector Type
* 0x00 NULL
* 0x08 Unused
* 0x10 32bit code
* 0x18 32bit data/stack
*/
/* The NULL Desciptor - Mandatory */
.word 0x0000 /* limit_low */
.word 0x0000 /* base_low */
.byte 0x00 /* base_middle */
.byte 0x00 /* access */
.byte 0x00 /* flags + limit_high */
.byte 0x00 /* base_high */
/* Unused Desciptor - (matches Linux) */
.word 0x0000 /* limit_low */
.word 0x0000 /* base_low */
.byte 0x00 /* base_middle */
.byte 0x00 /* access */
.byte 0x00 /* flags + limit_high */
.byte 0x00 /* base_high */
/*
* The Code Segment Descriptor:
* - Base = 0x00000000
* - Size = 4GB
* - Access = Present, Ring 0, Exec (Code), Readable
* - Flags = 4kB Granularity, 32-bit
*/
.word 0xffff /* limit_low */
.word 0x0000 /* base_low */
.byte 0x00 /* base_middle */
.byte 0x9b /* access */
.byte 0xcf /* flags + limit_high */
.byte 0x00 /* base_high */
/*
* The Data Segment Descriptor:
* - Base = 0x00000000
* - Size = 4GB
* - Access = Present, Ring 0, Non-Exec (Data), Writable
* - Flags = 4kB Granularity, 32-bit
*/
.word 0xffff /* limit_low */
.word 0x0000 /* base_low */
.byte 0x00 /* base_middle */
.byte 0x93 /* access */
.byte 0xcf /* flags + limit_high */
.byte 0x00 /* base_high */
#endif