u-boot/drivers/net/phy/realtek.c
Carlo Caione d47cfdbd31 net: phy: realtek: Introduce quirk to mark RXC not stoppable
When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.

A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.

Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-05-07 14:51:55 -05:00

397 lines
10 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* RealTek PHY drivers
*
* Copyright 2010-2011, 2015 Freescale Semiconductor, Inc.
* author Andy Fleming
* Copyright 2016 Karsten Merker <merker@debian.org>
*/
#include <common.h>
#include <linux/bitops.h>
#include <phy.h>
#define PHY_RTL8211x_FORCE_MASTER BIT(1)
#define PHY_RTL8211E_PINE64_GIGABIT_FIX BIT(2)
#define PHY_RTL8211F_FORCE_EEE_RXC_ON BIT(3)
#define PHY_AUTONEGOTIATE_TIMEOUT 5000
/* RTL8211x 1000BASE-T Control Register */
#define MIIM_RTL8211x_CTRL1000T_MSCE BIT(12);
#define MIIM_RTL8211x_CTRL1000T_MASTER BIT(11);
/* RTL8211x PHY Status Register */
#define MIIM_RTL8211x_PHY_STATUS 0x11
#define MIIM_RTL8211x_PHYSTAT_SPEED 0xc000
#define MIIM_RTL8211x_PHYSTAT_GBIT 0x8000
#define MIIM_RTL8211x_PHYSTAT_100 0x4000
#define MIIM_RTL8211x_PHYSTAT_DUPLEX 0x2000
#define MIIM_RTL8211x_PHYSTAT_SPDDONE 0x0800
#define MIIM_RTL8211x_PHYSTAT_LINK 0x0400
/* RTL8211x PHY Interrupt Enable Register */
#define MIIM_RTL8211x_PHY_INER 0x12
#define MIIM_RTL8211x_PHY_INTR_ENA 0x9f01
#define MIIM_RTL8211x_PHY_INTR_DIS 0x0000
/* RTL8211x PHY Interrupt Status Register */
#define MIIM_RTL8211x_PHY_INSR 0x13
/* RTL8211F PHY Status Register */
#define MIIM_RTL8211F_PHY_STATUS 0x1a
#define MIIM_RTL8211F_AUTONEG_ENABLE 0x1000
#define MIIM_RTL8211F_PHYSTAT_SPEED 0x0030
#define MIIM_RTL8211F_PHYSTAT_GBIT 0x0020
#define MIIM_RTL8211F_PHYSTAT_100 0x0010
#define MIIM_RTL8211F_PHYSTAT_DUPLEX 0x0008
#define MIIM_RTL8211F_PHYSTAT_SPDDONE 0x0800
#define MIIM_RTL8211F_PHYSTAT_LINK 0x0004
#define MIIM_RTL8211E_CONFREG 0x1c
#define MIIM_RTL8211E_CONFREG_TXD 0x0002
#define MIIM_RTL8211E_CONFREG_RXD 0x0004
#define MIIM_RTL8211E_CONFREG_MAGIC 0xb400 /* Undocumented */
#define MIIM_RTL8211E_EXT_PAGE_SELECT 0x1e
#define MIIM_RTL8211F_PAGE_SELECT 0x1f
#define MIIM_RTL8211F_TX_DELAY 0x100
#define MIIM_RTL8211F_LCR 0x10
static int rtl8211f_phy_extread(struct phy_device *phydev, int addr,
int devaddr, int regnum)
{
int oldpage = phy_read(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PAGE_SELECT);
int val;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, devaddr);
val = phy_read(phydev, MDIO_DEVAD_NONE, regnum);
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, oldpage);
return val;
}
static int rtl8211f_phy_extwrite(struct phy_device *phydev, int addr,
int devaddr, int regnum, u16 val)
{
int oldpage = phy_read(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PAGE_SELECT);
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, devaddr);
phy_write(phydev, MDIO_DEVAD_NONE, regnum, val);
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, oldpage);
return 0;
}
static int rtl8211b_probe(struct phy_device *phydev)
{
#ifdef CONFIG_RTL8211X_PHY_FORCE_MASTER
phydev->flags |= PHY_RTL8211x_FORCE_MASTER;
#endif
return 0;
}
static int rtl8211e_probe(struct phy_device *phydev)
{
#ifdef CONFIG_RTL8211E_PINE64_GIGABIT_FIX
phydev->flags |= PHY_RTL8211E_PINE64_GIGABIT_FIX;
#endif
return 0;
}
static int rtl8211f_probe(struct phy_device *phydev)
{
#ifdef CONFIG_RTL8211F_PHY_FORCE_EEE_RXC_ON
phydev->flags |= PHY_RTL8211F_FORCE_EEE_RXC_ON;
#endif
return 0;
}
/* RealTek RTL8211x */
static int rtl8211x_config(struct phy_device *phydev)
{
phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET);
/* mask interrupt at init; if the interrupt is
* needed indeed, it should be explicitly enabled
*/
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211x_PHY_INER,
MIIM_RTL8211x_PHY_INTR_DIS);
if (phydev->flags & PHY_RTL8211x_FORCE_MASTER) {
unsigned int reg;
reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_CTRL1000);
/* force manual master/slave configuration */
reg |= MIIM_RTL8211x_CTRL1000T_MSCE;
/* force master mode */
reg |= MIIM_RTL8211x_CTRL1000T_MASTER;
phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, reg);
}
if (phydev->flags & PHY_RTL8211E_PINE64_GIGABIT_FIX) {
unsigned int reg;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT,
7);
phy_write(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211E_EXT_PAGE_SELECT, 0xa4);
reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211E_CONFREG);
/* Ensure both internal delays are turned off */
reg &= ~(MIIM_RTL8211E_CONFREG_TXD | MIIM_RTL8211E_CONFREG_RXD);
/* Flip the magic undocumented bits */
reg |= MIIM_RTL8211E_CONFREG_MAGIC;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211E_CONFREG, reg);
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT,
0);
}
/* read interrupt status just to clear it */
phy_read(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211x_PHY_INER);
genphy_config_aneg(phydev);
return 0;
}
static int rtl8211f_config(struct phy_device *phydev)
{
u16 reg;
if (phydev->flags & PHY_RTL8211F_FORCE_EEE_RXC_ON) {
unsigned int reg;
reg = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_CTRL1);
reg &= ~MDIO_PCS_CTRL1_CLKSTOP_EN;
phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_CTRL1, reg);
}
phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET);
phy_write(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PAGE_SELECT, 0xd08);
reg = phy_read(phydev, MDIO_DEVAD_NONE, 0x11);
/* enable TX-delay for rgmii-id and rgmii-txid, otherwise disable it */
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
reg |= MIIM_RTL8211F_TX_DELAY;
else
reg &= ~MIIM_RTL8211F_TX_DELAY;
phy_write(phydev, MDIO_DEVAD_NONE, 0x11, reg);
/* restore to default page 0 */
phy_write(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PAGE_SELECT, 0x0);
/* Set green LED for Link, yellow LED for Active */
phy_write(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PAGE_SELECT, 0xd04);
phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x617f);
phy_write(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PAGE_SELECT, 0x0);
genphy_config_aneg(phydev);
return 0;
}
static int rtl8211x_parse_status(struct phy_device *phydev)
{
unsigned int speed;
unsigned int mii_reg;
mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211x_PHY_STATUS);
if (!(mii_reg & MIIM_RTL8211x_PHYSTAT_SPDDONE)) {
int i = 0;
/* in case of timeout ->link is cleared */
phydev->link = 1;
puts("Waiting for PHY realtime link");
while (!(mii_reg & MIIM_RTL8211x_PHYSTAT_SPDDONE)) {
/* Timeout reached ? */
if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
puts(" TIMEOUT !\n");
phydev->link = 0;
break;
}
if ((i++ % 1000) == 0)
putc('.');
udelay(1000); /* 1 ms */
mii_reg = phy_read(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211x_PHY_STATUS);
}
puts(" done\n");
udelay(500000); /* another 500 ms (results in faster booting) */
} else {
if (mii_reg & MIIM_RTL8211x_PHYSTAT_LINK)
phydev->link = 1;
else
phydev->link = 0;
}
if (mii_reg & MIIM_RTL8211x_PHYSTAT_DUPLEX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
speed = (mii_reg & MIIM_RTL8211x_PHYSTAT_SPEED);
switch (speed) {
case MIIM_RTL8211x_PHYSTAT_GBIT:
phydev->speed = SPEED_1000;
break;
case MIIM_RTL8211x_PHYSTAT_100:
phydev->speed = SPEED_100;
break;
default:
phydev->speed = SPEED_10;
}
return 0;
}
static int rtl8211f_parse_status(struct phy_device *phydev)
{
unsigned int speed;
unsigned int mii_reg;
int i = 0;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, 0xa43);
mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PHY_STATUS);
phydev->link = 1;
while (!(mii_reg & MIIM_RTL8211F_PHYSTAT_LINK)) {
if (i > PHY_AUTONEGOTIATE_TIMEOUT) {
puts(" TIMEOUT !\n");
phydev->link = 0;
break;
}
if ((i++ % 1000) == 0)
putc('.');
udelay(1000);
mii_reg = phy_read(phydev, MDIO_DEVAD_NONE,
MIIM_RTL8211F_PHY_STATUS);
}
if (mii_reg & MIIM_RTL8211F_PHYSTAT_DUPLEX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
speed = (mii_reg & MIIM_RTL8211F_PHYSTAT_SPEED);
switch (speed) {
case MIIM_RTL8211F_PHYSTAT_GBIT:
phydev->speed = SPEED_1000;
break;
case MIIM_RTL8211F_PHYSTAT_100:
phydev->speed = SPEED_100;
break;
default:
phydev->speed = SPEED_10;
}
return 0;
}
static int rtl8211x_startup(struct phy_device *phydev)
{
int ret;
/* Read the Status (2x to make sure link is right) */
ret = genphy_update_link(phydev);
if (ret)
return ret;
return rtl8211x_parse_status(phydev);
}
static int rtl8211e_startup(struct phy_device *phydev)
{
int ret;
ret = genphy_update_link(phydev);
if (ret)
return ret;
return genphy_parse_link(phydev);
}
static int rtl8211f_startup(struct phy_device *phydev)
{
int ret;
/* Read the Status (2x to make sure link is right) */
ret = genphy_update_link(phydev);
if (ret)
return ret;
/* Read the Status (2x to make sure link is right) */
return rtl8211f_parse_status(phydev);
}
/* Support for RTL8211B PHY */
static struct phy_driver RTL8211B_driver = {
.name = "RealTek RTL8211B",
.uid = 0x1cc912,
.mask = 0xffffff,
.features = PHY_GBIT_FEATURES,
.probe = &rtl8211b_probe,
.config = &rtl8211x_config,
.startup = &rtl8211x_startup,
.shutdown = &genphy_shutdown,
};
/* Support for RTL8211E-VB-CG, RTL8211E-VL-CG and RTL8211EG-VB-CG PHYs */
static struct phy_driver RTL8211E_driver = {
.name = "RealTek RTL8211E",
.uid = 0x1cc915,
.mask = 0xffffff,
.features = PHY_GBIT_FEATURES,
.probe = &rtl8211e_probe,
.config = &rtl8211x_config,
.startup = &rtl8211e_startup,
.shutdown = &genphy_shutdown,
};
/* Support for RTL8211DN PHY */
static struct phy_driver RTL8211DN_driver = {
.name = "RealTek RTL8211DN",
.uid = 0x1cc914,
.mask = 0xffffff,
.features = PHY_GBIT_FEATURES,
.config = &rtl8211x_config,
.startup = &rtl8211x_startup,
.shutdown = &genphy_shutdown,
};
/* Support for RTL8211F PHY */
static struct phy_driver RTL8211F_driver = {
.name = "RealTek RTL8211F",
.uid = 0x1cc916,
.mask = 0xffffff,
.features = PHY_GBIT_FEATURES,
.probe = &rtl8211f_probe,
.config = &rtl8211f_config,
.startup = &rtl8211f_startup,
.shutdown = &genphy_shutdown,
.readext = &rtl8211f_phy_extread,
.writeext = &rtl8211f_phy_extwrite,
};
int phy_realtek_init(void)
{
phy_register(&RTL8211B_driver);
phy_register(&RTL8211E_driver);
phy_register(&RTL8211F_driver);
phy_register(&RTL8211DN_driver);
return 0;
}