mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 10:18:38 +00:00
94c30f9c8f
As explained in commit 3bedbcc3aa ("arm: mvebu: a38x: serdes: Don't
overwrite read-only SAR PCIe registers") it is required to set Maximum Link
Width bits of PCIe Root Port Link Capabilities Register depending of number
of used serdes lanes. As this register is part of PCIe address space and
not serdes address space, move it into pci_mvebu.c driver.
Read number of PCIe lanes from DT property "num-lanes" which is used also
by other PCIe controller drivers in Linux kernel. If this property is
absent then it defaults to 1. This property needs to be set to 4 for every
mvebu board which use PEX_ROOT_COMPLEX_X4 or PEX_BUS_MODE_X4.
Enabling of PCIe port needs to be done afer all registers in PCIe address
space are properly configure. For this purpose use new mvebu-reset driver
(part of system-controller) and remove this code from serdes code.
Because some PCIe ports cannot be enabled individually, it is required to
first setup all PCIe ports and then enable them.
This change contains also all required "num-lanes" and "resets" DTS
properties, to make pci_mvebu.c driver work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
335 lines
7.6 KiB
Text
335 lines
7.6 KiB
Text
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Device Tree file for Synology DS414
|
|
*
|
|
* Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
|
|
*
|
|
* Note: this Device Tree assumes that the bootloader has remapped the
|
|
* internal registers to 0xf1000000 (instead of the old 0xd0000000).
|
|
* The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
|
|
* bootloaders provided by Marvell. It is used in recent versions of
|
|
* DSM software provided by Synology. Nonetheless, some earlier boards
|
|
* were delivered with an older version of u-boot that left internal
|
|
* registers mapped at 0xd0000000. If you have such a device you will
|
|
* not be able to directly boot a kernel based on this Device Tree. In
|
|
* that case, the preferred solution is to update your bootloader (e.g.
|
|
* by upgrading to latest version of DSM, or building a new one and
|
|
* installing it from u-boot prompt) or adjust the Devive Tree
|
|
* (s/0xf1000000/0xd0000000/ in 'ranges' below).
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include "armada-xp-mv78230.dtsi"
|
|
|
|
/ {
|
|
model = "Synology DS414";
|
|
compatible = "synology,ds414", "marvell,armadaxp-mv78230",
|
|
"marvell,armadaxp", "marvell,armada-370-xp";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200 earlyprintk";
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
aliases {
|
|
spi0 = &spi0;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0 0x00000000 0 0x40000000>; /* 1GB */
|
|
};
|
|
|
|
soc {
|
|
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
|
|
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
|
|
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
|
|
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000>;
|
|
|
|
internal-regs {
|
|
|
|
/* RTC is provided by Seiko S-35390A below */
|
|
rtc@10300 {
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c@11000 {
|
|
clock-frequency = <400000>;
|
|
status = "okay";
|
|
|
|
s35390a: s35390a@30 {
|
|
compatible = "sii,s35390a";
|
|
reg = <0x30>;
|
|
};
|
|
};
|
|
|
|
/* Connected to a header on device's PCB. This
|
|
* provides the main console for the device.
|
|
*
|
|
* Warning: the device may not boot with a 3.3V
|
|
* USB-serial converter connected when the power
|
|
* button is pressed. The converter needs to be
|
|
* connected a few seconds after pressing the
|
|
* power button. This is possibly due to UART0_TXD
|
|
* pin being sampled at reset (bit 0 of SAR).
|
|
*/
|
|
serial@12000 {
|
|
status = "okay";
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
/* Connected to a Microchip PIC16F883 for power control */
|
|
serial@12100 {
|
|
status = "okay";
|
|
};
|
|
|
|
poweroff@12100 {
|
|
compatible = "synology,power-off";
|
|
reg = <0x12100 0x100>;
|
|
clocks = <&coreclk 0>;
|
|
};
|
|
|
|
/* Front USB 2.0 port */
|
|
usb@50000 {
|
|
status = "okay";
|
|
};
|
|
|
|
ethernet@70000 {
|
|
status = "okay";
|
|
pinctrl-0 = <&ge0_rgmii_pins>;
|
|
pinctrl-names = "default";
|
|
phy = <&phy1>;
|
|
phy-mode = "rgmii-id";
|
|
};
|
|
|
|
ethernet@74000 {
|
|
pinctrl-0 = <&ge1_rgmii_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
phy = <&phy0>;
|
|
phy-mode = "rgmii-id";
|
|
};
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
|
|
&sata3_pwr_pin &sata4_pwr_pin>;
|
|
pinctrl-names = "default";
|
|
|
|
sata1_regulator: sata1-regulator@1 {
|
|
compatible = "regulator-fixed";
|
|
reg = <1>;
|
|
regulator-name = "SATA1 Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
startup-delay-us = <2000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sata2_regulator: sata2-regulator@2 {
|
|
compatible = "regulator-fixed";
|
|
reg = <2>;
|
|
regulator-name = "SATA2 Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
startup-delay-us = <4000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sata3_regulator: sata3-regulator@3 {
|
|
compatible = "regulator-fixed";
|
|
reg = <3>;
|
|
regulator-name = "SATA3 Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
startup-delay-us = <6000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sata4_regulator: sata4-regulator@4 {
|
|
compatible = "regulator-fixed";
|
|
reg = <4>;
|
|
regulator-name = "SATA4 Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
startup-delay-us = <8000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pciec {
|
|
status = "okay";
|
|
|
|
/*
|
|
* Connected to Marvell 88SX7042 SATA-II controller
|
|
* handling the four disks.
|
|
*/
|
|
pcie@1,0 {
|
|
/* Port 0, Lane 0 */
|
|
status = "okay";
|
|
num-lanes = <4>;
|
|
};
|
|
|
|
/*
|
|
* Connected to EtronTech EJ168A XHCI controller
|
|
* providing the two rear USB 3.0 ports.
|
|
*/
|
|
pcie@5,0 {
|
|
/* Port 1, Lane 0 */
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
|
|
&mdio {
|
|
phy0: ethernet-phy@0 { /* Marvell 88E1512 */
|
|
reg = <0>;
|
|
};
|
|
|
|
phy1: ethernet-phy@1 { /* Marvell 88E1512 */
|
|
reg = <1>;
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
sata1_pwr_pin: sata1-pwr-pin {
|
|
marvell,pins = "mpp42";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata2_pwr_pin: sata2-pwr-pin {
|
|
marvell,pins = "mpp44";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata3_pwr_pin: sata3-pwr-pin {
|
|
marvell,pins = "mpp45";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata4_pwr_pin: sata4-pwr-pin {
|
|
marvell,pins = "mpp46";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata1_pres_pin: sata1-pres-pin {
|
|
marvell,pins = "mpp34";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata2_pres_pin: sata2-pres-pin {
|
|
marvell,pins = "mpp35";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata3_pres_pin: sata3-pres-pin {
|
|
marvell,pins = "mpp40";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
sata4_pres_pin: sata4-pres-pin {
|
|
marvell,pins = "mpp41";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
syno_id_bit0_pin: syno-id-bit0-pin {
|
|
marvell,pins = "mpp26";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
syno_id_bit1_pin: syno-id-bit1-pin {
|
|
marvell,pins = "mpp28";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
syno_id_bit2_pin: syno-id-bit2-pin {
|
|
marvell,pins = "mpp29";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
fan1_alarm_pin: fan1-alarm-pin {
|
|
marvell,pins = "mpp33";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
fan2_alarm_pin: fan2-alarm-pin {
|
|
marvell,pins = "mpp32";
|
|
marvell,function = "gpio";
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
spi-flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "micron,n25q064", "jedec,spi-nor";
|
|
reg = <0>; /* Chip select 0 */
|
|
spi-max-frequency = <20000000>;
|
|
|
|
/*
|
|
* Warning!
|
|
*
|
|
* Synology u-boot uses its compiled-in environment
|
|
* and it seems Synology did not care to change u-boot
|
|
* default configuration in order to allow saving a
|
|
* modified environment at a sensible location. So,
|
|
* if you do a 'saveenv' under u-boot, your modified
|
|
* environment will be saved at 1MB after the start
|
|
* of the flash, i.e. in the middle of the uImage.
|
|
* For that reason, it is strongly advised not to
|
|
* change the default environment, unless you know
|
|
* what you are doing.
|
|
*/
|
|
partition@0 { /* u-boot */
|
|
label = "RedBoot";
|
|
reg = <0x00000000 0x000d0000>; /* 832KB */
|
|
};
|
|
|
|
partition@c0000 { /* uImage */
|
|
label = "zImage";
|
|
reg = <0x000d0000 0x002d0000>; /* 2880KB */
|
|
};
|
|
|
|
partition@3a0000 { /* uInitramfs */
|
|
label = "rd.gz";
|
|
reg = <0x003a0000 0x00430000>; /* 4250KB */
|
|
};
|
|
|
|
partition@7d0000 { /* MAC address and serial number */
|
|
label = "vendor";
|
|
reg = <0x007d0000 0x00010000>; /* 64KB */
|
|
};
|
|
|
|
partition@7e0000 {
|
|
label = "RedBoot config";
|
|
reg = <0x007e0000 0x00010000>; /* 64KB */
|
|
};
|
|
|
|
partition@7f0000 {
|
|
label = "FIS directory";
|
|
reg = <0x007f0000 0x00010000>; /* 64KB */
|
|
};
|
|
};
|
|
};
|