u-boot/board/BuS/eb_cpux9k2/cpux9k2.c
Joe Hershberger d2eaec6006 net: Remove the bd* parameter from net stack functions
This value is not used by the network stack and is available in the
global data, so stop passing it around.  For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
2015-04-18 11:11:11 -06:00

373 lines
8.1 KiB
C

/*
* (C) Copyright 2008-2009
* BuS Elektronik GmbH & Co. KG <www.bus-elektronik.de>
* Jens Scharsig <esw@bus-elektronik.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <exports.h>
#include <net.h>
#include <netdev.h>
#include <nand.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/at91_pio.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_mc.h>
#include <asm/arch/at91_common.h>
#ifdef CONFIG_STATUS_LED
#include <status_led.h>
#endif
#ifdef CONFIG_VIDEO
#include <bus_vcxk.h>
extern unsigned long display_width;
extern unsigned long display_height;
#endif
#ifdef CONFIG_CMD_NAND
void cpux9k2_nand_hw_init(void);
#endif
DECLARE_GLOBAL_DATA_PTR;
/*
* Miscelaneous platform dependent initialisations
*/
int board_init(void)
{
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
/* Correct IRDA resistor problem / Set PA23_TXD in Output */
writel(ATMEL_PMX_AA_TXD2, &pio->pioa.oer);
gd->bd->bi_arch_number = MACH_TYPE_EB_CPUX9K2;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_STATUS_LED
status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
#endif
#ifdef CONFIG_CMD_NAND
cpux9k2_nand_hw_init();
#endif
return 0;
}
int board_early_init_f(void)
{
at91_seriald_hw_init();
return 0;
}
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
uchar mac[8];
uchar tm;
uchar midx;
uchar macn6, macn7;
if (getenv("ethaddr") == NULL) {
if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0x00,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
(uchar *) &mac, sizeof(mac)) != 0) {
puts("Error reading MAC from EEPROM\n");
} else {
tm = 0;
macn6 = 0;
macn7 = 0xFF;
for (midx = 0; midx < 6; midx++) {
if ((mac[midx] != 0) && (mac[midx] != 0xFF))
tm++;
macn6 += mac[midx];
macn7 ^= mac[midx];
}
if ((macn6 != mac[6]) || (macn7 != mac[7]))
tm = 0;
if (tm)
eth_setenv_enetaddr("ethaddr", mac);
else
puts("Error: invalid MAC at EEPROM\n");
}
}
gd->jt->do_reset = do_reset;
#ifdef CONFIG_STATUS_LED
status_led_set(STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
return 0;
}
#endif
#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
udelay(10000);
eth_init();
}
#endif
/*
* DRAM initialisations
*/
int dram_init(void)
{
gd->ram_size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
/*
* Ethernet initialisations
*/
#ifdef CONFIG_DRIVER_AT91EMAC
int board_eth_init(bd_t *bis)
{
int rc = 0;
rc = at91emac_register(bis, (u32) ATMEL_BASE_EMAC);
return rc;
}
#endif
/*
* Disk On Chip (NAND) Millenium initialization.
* The NAND lives in the CS2* space
*/
#if defined(CONFIG_CMD_NAND)
#define MASK_ALE (1 << 22) /* our ALE is AD22 */
#define MASK_CLE (1 << 21) /* our CLE is AD21 */
void cpux9k2_nand_hw_init(void)
{
unsigned long csr;
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_mc_t *mc = (at91_mc_t *) ATMEL_BASE_MC;
/* Setup Smart Media, fitst enable the address range of CS3 */
writel(readl(&mc->ebi.csa) | AT91_EBI_CSA_CS3A, &mc->ebi.csa);
/* RWH = 1 | RWS = 0 | TDF = 1 | NWS = 3 */
csr = AT91_SMC_CSR_RWHOLD(1) | AT91_SMC_CSR_TDF(1) |
AT91_SMC_CSR_NWS(3) |
AT91_SMC_CSR_ACSS_STANDARD | AT91_SMC_CSR_DBW_8 |
AT91_SMC_CSR_WSEN;
writel(csr, &mc->smc.csr[3]);
writel(ATMEL_PMX_CA_SMOE | ATMEL_PMX_CA_SMWE, &pio->pioc.asr);
writel(ATMEL_PMX_CA_BFCK | ATMEL_PMX_CA_SMOE | ATMEL_PMX_CA_SMWE,
&pio->pioc.pdr);
/* Configure PC2 as input (signal Nand READY ) */
writel(ATMEL_PMX_CA_BFAVD, &pio->pioc.per);
writel(ATMEL_PMX_CA_BFAVD, &pio->pioc.odr); /* disable output */
writel(ATMEL_PMX_CA_BFCK, &pio->pioc.codr);
/* PIOC clock enabling */
writel(1 << ATMEL_ID_PIOC, &pmc->pcer);
}
static void board_nand_hwcontrol(struct mtd_info *mtd,
int cmd, unsigned int ctrl)
{
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
struct nand_chip *this = mtd->priv;
ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
if (ctrl & NAND_CTRL_CHANGE) {
IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
if (ctrl & NAND_CLE)
IO_ADDR_W |= MASK_CLE;
if (ctrl & NAND_ALE)
IO_ADDR_W |= MASK_ALE;
if ((ctrl & NAND_NCE))
writel(1, &pio->pioc.codr);
else
writel(1, &pio->pioc.sodr);
this->IO_ADDR_W = (void *) IO_ADDR_W;
}
if (cmd != NAND_CMD_NONE)
writeb(cmd, this->IO_ADDR_W);
}
static int board_nand_dev_ready(struct mtd_info *mtd)
{
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
return ((readl(&pio->pioc.pdsr) & (1 << 2)) != 0);
}
int board_nand_init(struct nand_chip *nand)
{
cpux9k2_nand_hw_init();
nand->ecc.mode = NAND_ECC_SOFT;
nand->cmd_ctrl = board_nand_hwcontrol;
nand->dev_ready = board_nand_dev_ready;
nand->chip_delay = 20;
return 0;
}
#endif
#if defined(CONFIG_VIDEO)
/*
* drv_video_init
* FUNCTION: initialize VCxK device
*/
int drv_video_init(void)
{
#ifdef CONFIG_SPLASH_SCREEN
unsigned long splash;
#endif
char *s;
unsigned long csr;
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_mc_t *mc = (at91_mc_t *) ATMEL_BASE_MC;
printf("Init Video as ");
s = getenv("displaywidth");
if (s != NULL)
display_width = simple_strtoul(s, NULL, 10);
else
display_width = 256;
s = getenv("displayheight");
if (s != NULL)
display_height = simple_strtoul(s, NULL, 10);
else
display_height = 256;
printf("%ld x %ld pixel matrix\n", display_width, display_height);
/* RWH = 2 | RWS =2 | TDF = 4 | NWS = 0x6 */
csr = AT91_SMC_CSR_RWHOLD(2) | AT91_SMC_CSR_RWSETUP(2) |
AT91_SMC_CSR_TDF(4) | AT91_SMC_CSR_NWS(6) |
AT91_SMC_CSR_ACSS_STANDARD | AT91_SMC_CSR_DBW_16 |
AT91_SMC_CSR_BAT_16 | AT91_SMC_CSR_WSEN;
writel(csr, &mc->smc.csr[2]);
writel(1 << ATMEL_ID_PIOB, &pmc->pcer);
vcxk_init(display_width, display_height);
#ifdef CONFIG_SPLASH_SCREEN
s = getenv("splashimage");
if (s != NULL) {
splash = simple_strtoul(s, NULL, 16);
printf("use splashimage: %lx\n", splash);
video_display_bitmap(splash, 0, 0);
}
#endif
return 0;
}
#endif
#ifdef CONFIG_SYS_I2C_SOFT
void i2c_init_board(void)
{
u32 pin;
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
writel(1 << ATMEL_ID_PIOA, &pmc->pcer);
pin = ATMEL_PMX_AA_TWD | ATMEL_PMX_AA_TWCK;
writel(pin, &pio->pioa.idr);
writel(pin, &pio->pioa.pudr);
writel(pin, &pio->pioa.per);
writel(pin, &pio->pioa.oer);
writel(pin, &pio->pioa.sodr);
}
#endif
/*--------------------------------------------------------------------------*/
#ifdef CONFIG_STATUS_LED
void __led_toggle(led_id_t mask)
{
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
if (readl(&pio->piod.odsr) & mask)
writel(mask, &pio->piod.codr);
else
writel(mask, &pio->piod.codr);
}
void __led_init(led_id_t mask, int state)
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
writel(1 << ATMEL_ID_PIOD, &pmc->pcer); /* Enable PIOB clock */
/* Disable peripherals on LEDs */
writel(STATUS_LED_BIT | STATUS_LED_BIT1, &pio->piod.per);
/* Enable pins as outputs */
writel(STATUS_LED_BIT | STATUS_LED_BIT1, &pio->piod.oer);
/* Turn all LEDs OFF */
writel(STATUS_LED_BIT | STATUS_LED_BIT1, &pio->piod.sodr);
__led_set(mask, state);
}
void __led_set(led_id_t mask, int state)
{
at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO;
if (state == STATUS_LED_ON)
writel(mask, &pio->piod.codr);
else
writel(mask, &pio->piod.sodr);
}
#endif
/*---------------------------------------------------------------------------*/
int do_brightness(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int rcode = 0;
ulong side;
ulong bright;
switch (argc) {
case 3:
side = simple_strtoul(argv[1], NULL, 10);
bright = simple_strtoul(argv[2], NULL, 10);
if ((side >= 0) && (side <= 3) &&
(bright >= 0) && (bright <= 1000)) {
vcxk_setbrightness(side, bright);
rcode = 0;
} else {
printf("parameters out of range\n");
printf("Usage:\n%s\n", cmdtp->usage);
rcode = 1;
}
break;
default:
printf("Usage:\n%s\n", cmdtp->usage);
rcode = 1;
break;
}
return rcode;
}
/*---------------------------------------------------------------------------*/
U_BOOT_CMD(
bright, 3, 0, do_brightness,
"bright - sets the display brightness\n",
" <side> <0..1000>\n side: 0/3=both; 1=first; 2=second\n"
);
/* EOF cpu9k2.c */