mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-04 10:30:32 +00:00
ea83ea5afd
This supports Falcon boot support for Microchip SAMA5D3 Xplained, tested on raw MMC, and on raw NAND. spl_start_uboot() is has the simplest possible implementation. It doesn't test the environment because enabling environment support currently causes the SPL to exceed its maximum size (64 KiB). It doesn't check the serial for incoming characters either because this functionality currently doesn't seem to work from the SPL on this board. Settings for Falcon boot from at FAT partition are also added to avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this particular case is currently not functional as adding FAT and partition support cause the SPL to be too big again. Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
96 lines
2.7 KiB
C
96 lines
2.7 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Configuration settings for the SAMA5D3 Xplained board.
|
|
*
|
|
* Copyright (C) 2014 Atmel Corporation
|
|
* Bo Shen <voice.shen@atmel.com>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#include <linux/sizes.h>
|
|
#include "at91-sama5_common.h"
|
|
|
|
/*
|
|
* This needs to be defined for the OHCI code to work but it is defined as
|
|
* ATMEL_ID_UHPHS in the CPU specific header files.
|
|
*/
|
|
#define ATMEL_ID_UHP 32
|
|
|
|
/*
|
|
* Specify the clock enable bit in the PMC_SCER register.
|
|
*/
|
|
#define ATMEL_PMC_UHP (1 << 6)
|
|
|
|
/* SDRAM */
|
|
#define CONFIG_SYS_SDRAM_BASE 0x20000000
|
|
#define CONFIG_SYS_SDRAM_SIZE 0x10000000
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#define CONFIG_SYS_INIT_SP_ADDR 0x318000
|
|
#else
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
|
|
#endif
|
|
|
|
/* NAND flash */
|
|
#ifdef CONFIG_CMD_NAND
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE 0x60000000
|
|
/* our ALE is AD21 */
|
|
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
|
|
/* our CLE is AD22 */
|
|
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
#endif
|
|
|
|
/* USB */
|
|
#ifdef CONFIG_CMD_USB
|
|
#define CONFIG_USB_ATMEL
|
|
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
|
|
#define CONFIG_USB_OHCI_NEW
|
|
#define CONFIG_SYS_USB_OHCI_CPU_INIT
|
|
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00600000
|
|
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained"
|
|
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
|
|
#endif
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
|
|
|
|
/* SPL */
|
|
#define CONFIG_SPL_MAX_SIZE 0x18000
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
|
|
|
|
/* size of u-boot.bin to load */
|
|
#define CONFIG_SYS_MONITOR_LEN (2 * SZ_512K)
|
|
|
|
#ifdef CONFIG_SD_BOOT
|
|
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
#endif
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT 64
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
|
|
|
|
/* Falcon boot support on raw MMC */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x100 /* 128 KiB */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
|
|
/* U-Boot proper stored by default at 0x200 (256 KiB) */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */
|
|
#define CONFIG_SYS_SPL_ARGS_ADDR 0x22000000
|
|
|
|
/* Falcon boot support on FAT on MMC */
|
|
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
|
|
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
|
|
|
|
/* Falcon boot support on raw NAND */
|
|
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x1a0000
|
|
|
|
#endif
|