u-boot/arch/arm/dts/stm32mp157c-ev1.dts
Patrick Delaunay 1258e4667a ARM: dts: Add STMFX gpio expander support for stm32mp157c-ev1
Adds alias to set the pincontrol seq id.
For STMFX gpio expander, force sequence number after
the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX
gpio bank sequence number.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12 16:09:13 +02:00

234 lines
4 KiB
Text

// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/
/dts-v1/;
#include "stm32mp157c-ed1.dts"
/ {
model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
chosen {
stdout-path = "serial0:115200n8";
};
aliases {
serial0 = &uart4;
ethernet0 = &ethernet0;
};
panel_backlight: panel-backlight {
compatible = "gpio-backlight";
gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
default-on;
status = "okay";
};
};
&cec {
pinctrl-names = "default";
pinctrl-0 = <&cec_pins_a>;
status = "okay";
};
&dsi {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
dsi_in: endpoint {
remote-endpoint = <&ltdc_ep0_out>;
};
};
port@1 {
reg = <1>;
dsi_out: endpoint {
remote-endpoint = <&dsi_panel_in>;
};
};
};
panel-dsi@0 {
compatible = "raydium,rm68200";
reg = <0>;
reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
backlight = <&panel_backlight>;
status = "okay";
port {
dsi_panel_in: endpoint {
remote-endpoint = <&dsi_out>;
};
};
};
};
&ethernet0 {
status = "okay";
pinctrl-0 = <&ethernet0_rgmii_pins_a>;
pinctrl-1 = <&ethernet0_rgmii_pins_sleep_a>;
pinctrl-names = "default", "sleep";
phy-mode = "rgmii";
max-speed = <1000>;
phy-handle = <&phy0>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@0 {
reg = <0>;
};
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
stmfx: stmfx@42 {
compatible = "st,stmfx-0300";
reg = <0x42>;
interrupts = <8 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gpioi>;
vdd-supply = <&v3v3>;
stmfx_pinctrl: stmfx-pin-controller {
compatible = "st,stmfx-0300-pinctrl";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&stmfx_pinctrl 0 0 24>;
status = "disabled";
};
};
};
&i2c5 {
pinctrl-names = "default";
pinctrl-0 = <&i2c5_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
};
&ltdc {
status = "okay";
port {
#address-cells = <1>;
#size-cells = <0>;
ltdc_ep0_out: endpoint@0 {
reg = <0>;
remote-endpoint = <&dsi_in>;
};
};
};
&m_can1 {
pinctrl-names = "default";
pinctrl-0 = <&m_can1_pins_a>;
status = "okay";
};
&qspi {
pinctrl-names = "default";
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
flash0: mx66l51235l@0 {
reg = <0>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>;
#address-cells = <1>;
#size-cells = <1>;
};
flash1: mx66l51235l@1 {
reg = <1>;
spi-rx-bus-width = <4>;
spi-max-frequency = <108000000>;
#address-cells = <1>;
#size-cells = <1>;
};
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins_a>;
status = "disabled";
};
&timers2 {
status = "disabled";
pwm {
pinctrl-0 = <&pwm2_pins_a>;
pinctrl-names = "default";
status = "okay";
};
timer@1 {
status = "okay";
};
};
&timers8 {
status = "disabled";
pwm {
pinctrl-0 = <&pwm8_pins_a>;
pinctrl-names = "default";
status = "okay";
};
timer@7 {
status = "okay";
};
};
&timers12 {
status = "disabled";
pwm {
pinctrl-0 = <&pwm12_pins_a>;
pinctrl-names = "default";
status = "okay";
};
timer@11 {
status = "okay";
};
};
&usbh_ehci {
phys = <&usbphyc_port0>;
phy-names = "usb";
vbus-supply = <&vbus_sw>;
status = "okay";
};
&usbotg_hs {
pinctrl-names = "default";
pinctrl-0 = <&usbotg_hs_pins_a>;
dr_mode = "peripheral";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
};
&usbphyc {
status = "okay";
};