u-boot/arch/arm/dts/armada-3720-uDPU.dts
Vladimir Vid 32c9e1c269 arm64: mvebu: Add basic support for uDPU board
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).

On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)

Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-02-05 14:23:06 +01:00

200 lines
3.8 KiB
Text

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device tree for the uDPU board.
* Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
* Copyright (C) 2016 Marvell
* Copyright (C) 2018 Methode
* Copyright (C) 2018 Telus
*
* Vladimir Vid <vladimir.vid@sartura.hr>
*/
/dts-v1/;
#include "armada-37xx.dtsi"
#include "armada-3720-uDPU-u-boot.dtsi"
/ {
model = "Methode uDPU Board";
compatible = "methode,udpu";
chosen {
stdout-path = "serial0:115200n8";
bootargs = "console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000";
};
aliases {
i2c0 = &i2c0;
i2c1 = &i2c1;
spi0 = &spi0;
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
mdio: mdio@32004 {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy@0 {
reg = <0>;
};
ethphy1: ethernet-phy@1 {
reg = <1>;
};
};
scsi: scsi {
compatible = "marvell,mvebu-scsi";
#address-cells = <1>;
#size-cells = <1>;
max-id = <1>;
max-lun = <1>;
status = "okay";
};
i2c1: i2c@11080 {
compatible = "marvell,armada-3700-i2c", "simple-bus";
reg = <0x0 0x11080 0x0 0x80>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
#address-cells = <2>;
#size-cells = <2>;
status = "okay";
};
uart1: serial@12200 {
compatible = "marvell,armada-3700-uart-ext";
reg = <0x0 0x12200 0x0 0x30>;
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
status = "okay";
#address-cells = <2>;
#size-cells = <2>;
};
vcc_sd_reg0: regulator@0 {
compatible = "regulator-gpio";
regulator-name = "vcc_sd0";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-type = "voltage";
states = <1800000 0x1
3300000 0x0>;
gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
};
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
};
sfp_eth1: sfp-eth1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
sfp,ethernet = <&eth1>;
los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
};
};
&comphy {
phy0 {
phy-type = <PHY_TYPE_SGMII1>;
phy-speed = <PHY_SPEED_1_25G>;
};
phy1 {
phy-type = <PHY_TYPE_SGMII0>;
phy-speed = <PHY_SPEED_1_25G>;
};
phy2 {
phy-type = <PHY_TYPE_USB3_HOST1>;
phy-speed = <PHY_SPEED_5G>;
};
};
&eth0 {
pinctrl-0 = <&pcie_pins>;
status = "okay";
phy-mode = "sgmii";
phy = <&ethphy0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&eth1 {
status = "okay";
phy-mode = "sgmii";
phy = <&ethphy1>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "okay";
};
&spi0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi_quad_pins>;
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "n25q1024a","n25q512a";
reg = <0>;
spi-max-frequency = <50000000>;
spi-rx-bus-width = <4>;
spi-tx-bus-width = <4>;
m25p,fast-read;
partition@0 {
label = "uboot";
reg = <0 0x400000>;
};
};
};
&sdhci1 {
non-removable;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
bus-width = <4>;
vqmmc-supply = <&vcc_sd_reg0>;
pinctrl-names = "default";
pinctrl-0 = <&sdio_pins>;
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
mmccard: mmccard@0 {
compatible = "mmc-card";
reg = <0>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "okay";
};
&usb3 {
status = "okay";
};