mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 02:08:38 +00:00
f858bcccf4
Add the Octeon ethernet (BGX) and SFP DT nodes to the NIC23 dts file to enable ethernet support on this board. Signed-off-by: Stefan Roese <sr@denx.de>
400 lines
8.8 KiB
Text
400 lines
8.8 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Marvell / Cavium Inc. NIC23
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "mrvl,cn73xx.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
model = "cavium,nic23";
|
|
compatible = "cavium,nic23";
|
|
|
|
aliases {
|
|
mmc0 = &mmc0;
|
|
serial0 = &uart0;
|
|
spi0 = &spi;
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
/* Power on GPIO 8, active high */
|
|
reg_mmc_3v3: regulator@0 {
|
|
compatible = "regulator-fixed";
|
|
reg = <0>;
|
|
regulator-name = "mmc-3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = &uart0;
|
|
};
|
|
};
|
|
|
|
&bootbus {
|
|
/*
|
|
* bootbus CS0 for CFI flash is remapped (0x1fc0.0000 -> 1f40.0000)
|
|
* as the initial size is too small for the 8MiB flash device
|
|
*/
|
|
ranges = <0 0 0 0x1f400000 0xc00000>,
|
|
<1 0 0x10000 0x10000000 0>,
|
|
<2 0 0x10000 0x20000000 0>,
|
|
<3 0 0x10000 0x30000000 0>,
|
|
<4 0 0 0x1d020000 0x10000>,
|
|
<5 0 0x10000 0x50000000 0>,
|
|
<6 0 0x10000 0x60000000 0>,
|
|
<7 0 0x10000 0x70000000 0>;
|
|
|
|
cavium,cs-config@0 {
|
|
compatible = "cavium,octeon-3860-bootbus-config";
|
|
cavium,cs-index = <0>;
|
|
cavium,t-adr = <10>;
|
|
cavium,t-ce = <50>;
|
|
cavium,t-oe = <50>;
|
|
cavium,t-we = <35>;
|
|
cavium,t-rd-hld = <25>;
|
|
cavium,t-wr-hld = <35>;
|
|
cavium,t-pause = <0>;
|
|
cavium,t-wait = <50>;
|
|
cavium,t-page = <30>;
|
|
cavium,t-rd-dly = <0>;
|
|
cavium,page-mode = <1>;
|
|
cavium,pages = <8>;
|
|
cavium,bus-width = <8>;
|
|
};
|
|
|
|
cavium,cs-config@4 {
|
|
compatible = "cavium,octeon-3860-bootbus-config";
|
|
cavium,cs-index = <4>;
|
|
cavium,t-adr = <10>;
|
|
cavium,t-ce = <10>;
|
|
cavium,t-oe = <160>;
|
|
cavium,t-we = <100>;
|
|
cavium,t-rd-hld = <10>;
|
|
cavium,t-wr-hld = <0>;
|
|
cavium,t-pause = <50>;
|
|
cavium,t-wait = <50>;
|
|
cavium,t-page = <10>;
|
|
cavium,t-rd-dly = <10>;
|
|
cavium,pages = <0>;
|
|
cavium,bus-width = <8>;
|
|
};
|
|
|
|
flash0: nor@0,0 {
|
|
compatible = "cfi-flash";
|
|
reg = <0 0 0x800000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
partition@0 {
|
|
label = "bootloader";
|
|
reg = <0 0x340000>;
|
|
read-only;
|
|
};
|
|
partition@300000 {
|
|
label = "storage";
|
|
reg = <0x340000 0x4be000>;
|
|
};
|
|
partition@7fe000 {
|
|
label = "environment";
|
|
reg = <0x7fe000 0x2000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
clock-frequency = <800000000>;
|
|
};
|
|
|
|
&i2c0 {
|
|
u-boot,dm-pre-reloc; /* Needed early for DDR SPD EEPROM */
|
|
clock-frequency = <100000>;
|
|
|
|
sfp0eeprom: eeprom@50 {
|
|
compatible = "atmel,24c01";
|
|
reg = <0x50>;
|
|
};
|
|
|
|
sfp0alerts: eeprom@51 {
|
|
compatible = "atmel,24c01";
|
|
reg = <0x51>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
u-boot,dm-pre-reloc; /* Needed early for DDR SPD EEPROM */
|
|
clock-frequency = <100000>;
|
|
|
|
vitesse@10 {
|
|
compatible = "vitesse,vsc7224";
|
|
reg = <0x10>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
/* Note that reset is active high with this device */
|
|
reset = <&gpio 7 0>;
|
|
|
|
/* LoS pin can be pulled low when there is a loss of signal */
|
|
los = <&gpio 6 0>;
|
|
|
|
vitesse,reg-init =
|
|
/* Clear all masks */
|
|
/* Page select FSYNC0 (0x30) */
|
|
<0x7f 0x0030>,
|
|
/* Set FSYNC0 for 10.3125Gbps */
|
|
<0x80 0x2841>, /* See Table 3. */
|
|
<0x81 0x0008>,
|
|
<0x82 0xc000>,
|
|
<0x83 0x0010>,
|
|
<0x84 0x1d00>,
|
|
|
|
/* All channels Rx settings set equally */
|
|
<0x7f 0x0050>,
|
|
/* Shrink EQ_BUFF */
|
|
<0x82 0x0014>,
|
|
/* Set EQVGA_ADAP = 1 (enable EQVGA circuitry),
|
|
* USE_UNIT_GAIN = 1 (EQVGA is in unity gain),
|
|
* USE_LPF = 0 (VGA adapt not using LPF),
|
|
* USE_EQVGA = 1
|
|
<0x89 0x7f13>,
|
|
/* Select min DFE Delay (DFE_DELAY) */
|
|
<0x90 0x5785>,
|
|
/* Set DFE 1-3 limit (DXMAX) = 32dec,
|
|
* AP Max limit = 127 decimal
|
|
*/
|
|
<0x92 0x207f>,
|
|
/* Set AP Min limit = 32 decimal */
|
|
<0x93 0x2000>,
|
|
/* Set DFE Averaging to the slowest (DFE_AVG) */
|
|
<0x94 0x0031>,
|
|
/* Set Inductor Bypass OD_IND_BYP = 0 & fastest Rise/Fall */
|
|
<0x9c 0x0000>,
|
|
/* Setting DFE Boost = none. Must set for
|
|
* rev C (if DFE in adapt mode)
|
|
*/
|
|
<0xaa 0x0888>,
|
|
/* Setting EQ Min = 8 & Max limit = 72 dec.
|
|
* Must set for rev C, otherwise EQ is 0
|
|
* (if EQ is in adaptive mode)
|
|
*/
|
|
<0xa8 0x2408>,
|
|
/* Setting EQVGA = 96, when in EQVGA manual mode */
|
|
<0xa9 0x0060>,
|
|
/* Setting SW_BFOCM, bits 15:14 to 01 */
|
|
<0x87 0x4021>,
|
|
/* Turn off adaptive input equalization
|
|
* and VGA adaptive algorithm control.
|
|
*/
|
|
<0x89 0x7313>,
|
|
/* Turn on adaptive input equalization
|
|
* and VGA adaptive algorithm control.
|
|
*/
|
|
<0x89 0x7f13>;
|
|
|
|
vitesse-channel@0 {
|
|
compatible = "vitesse,vsc7224-channel";
|
|
reg = <0>;
|
|
direction-tx;
|
|
sfp-mac = <ð0>;
|
|
|
|
/* TAP settings. The format of this is as
|
|
* follows:
|
|
* - cable length in meters, 0 = active or
|
|
* optical module
|
|
* - maintap value
|
|
* - pretap value
|
|
* - posttap value
|
|
*
|
|
* For the cable length, the value will apply
|
|
* for that cable length and greater until the
|
|
* next largest cable length specified. These
|
|
* values must be ordered first by channel mask
|
|
* then by cable length. These are typically
|
|
* set for the transmit channels, not the
|
|
* receive channels.
|
|
*/
|
|
taps = <0 0x0013 0x000f 0x0000>,
|
|
<1 0x001f 0x000f 0x0004>,
|
|
<3 0x0014 0x000b 0x0004>,
|
|
<5 0x0014 0x0009 0x0006>,
|
|
<7 0x0014 0x000f 0x0000>,
|
|
<10 0x0012 0x000b 0x0013>;
|
|
};
|
|
|
|
vitesse-channel@1 {
|
|
compatible = "vitesse,vsc7224-channel";
|
|
reg = <1>;
|
|
/* Ignore mod_abs and module */
|
|
direction-rx;
|
|
sfp-mac = <ð0>;
|
|
|
|
/* Disable pre-tap */
|
|
pretap-disable;
|
|
|
|
/* Disable post-tap */
|
|
posttap-disable;
|
|
|
|
/* Taps has the following fields:
|
|
* - cable length (ignored for rx)
|
|
* - main tap value
|
|
* - pre tap value
|
|
* - post tap value
|
|
*
|
|
* NOTE: if taps are disabled then they
|
|
* are not programmed.
|
|
*/
|
|
taps = <0 0x0a 0x0b 0x10>;
|
|
};
|
|
|
|
vitesse-channel@2 {
|
|
compatible = "vitesse,vsc7224-channel";
|
|
reg = <2>;
|
|
direction-tx;
|
|
sfp-mac = <ð1>;
|
|
|
|
/* TAP settings. The format of this is as
|
|
* follows:
|
|
* - cable length in meters, 0 = active or
|
|
* optical module
|
|
* - maintap value
|
|
* - pretap value
|
|
* - posttap value
|
|
*
|
|
* For the cable length, the value will apply
|
|
* for that cable length and greater until the
|
|
* next largest cable length specified. These
|
|
* values must be ordered first by channel mask
|
|
* then by cable length. These are typically
|
|
* set for the transmit channels, not the
|
|
* receive channels.
|
|
*/
|
|
taps = <0 0x0013 0x000f 0x0000>,
|
|
<1 0x001f 0x000f 0x0004>,
|
|
<3 0x0014 0x000b 0x0004>,
|
|
<5 0x0014 0x0009 0x0006>,
|
|
<7 0x0014 0x000f 0x0000>,
|
|
<10 0x0012 0x000b 0x0013>;
|
|
};
|
|
|
|
vitesse-channel@3 {
|
|
compatible = "vitesse,vsc7224-channel";
|
|
reg = <3>;
|
|
/* Ignore mod_abs and module */
|
|
direction-rx;
|
|
sfp-mac = <ð1>;
|
|
|
|
/* Disable pre-tap */
|
|
pretap-disable;
|
|
|
|
/* Disable post-tap */
|
|
posttap-disable;
|
|
|
|
/* Taps has the following fields:
|
|
* - cable length (ignored for rx)
|
|
* - main tap value
|
|
* - pre tap value
|
|
* - post tap value
|
|
*
|
|
* NOTE: if taps are disabled then they
|
|
* are not programmed.
|
|
*/
|
|
taps = <0 0x0a 0x0b 0x10>;
|
|
};
|
|
};
|
|
|
|
sfp1eeprom: eeprom@50 {
|
|
compatible = "atmel,24c01";
|
|
reg = <0x50>;
|
|
};
|
|
|
|
sfp1alerts: eeprom@51 {
|
|
compatible = "atmel,24c01";
|
|
reg = <0x51>;
|
|
};
|
|
};
|
|
|
|
&mmc {
|
|
status = "okay";
|
|
|
|
mmc0: mmc-slot@0 {
|
|
compatible = "cavium,octeon-6130-mmc-slot", "mmc-slot";
|
|
reg = <0>;
|
|
vqmmc-supply = <®_mmc_3v3>;
|
|
voltage-ranges = <3300 3300>;
|
|
spi-max-frequency = <52000000>;
|
|
/* bus width can be 1, 4 or 8 */
|
|
bus-width = <8>; /* new std property */
|
|
cavium,bus-max-width = <8>; /* custom property */
|
|
non-removable;
|
|
};
|
|
};
|
|
|
|
&soc0 {
|
|
pci-console@0 {
|
|
compatible = "marvell,pci-console";
|
|
status = "okay";
|
|
};
|
|
|
|
pci-bootcmd@0 {
|
|
compatible = "marvell,pci-bootcmd";
|
|
status = "okay";
|
|
};
|
|
|
|
sfp0: sfp-slot@0 {
|
|
compatible = "ethernet,sfp-slot";
|
|
tx_disable = <&gpio 16 0>;
|
|
mod_abs = <&gpio 17 0>;
|
|
tx_error = <&gpio 19 0>;
|
|
rx_los = <&gpio 18 0>;
|
|
eeprom = <&sfp0eeprom>;
|
|
diag = <&sfp0alerts>;
|
|
};
|
|
|
|
sfp1: sfp-slot@1 {
|
|
compatible = "ethernet,sfp-slot";
|
|
tx_disable = <&gpio 21 0>;
|
|
mod_abs = <&gpio 22 0>;
|
|
tx_error = <&gpio 24 0>;
|
|
rx_los = <&gpio 23 0>;
|
|
eeprom = <&sfp1eeprom>;
|
|
diag = <&sfp1alerts>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
flash@0 {
|
|
compatible = "micron,n25q128a11", "jedec,spi-nor";
|
|
spi-max-frequency = <2000000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
/* BGX 2 */
|
|
&bgx2 {
|
|
status = "okay";
|
|
|
|
/* SerDes 0, may differ from PCS Lane/LMAC */
|
|
eth0: ethernet-mac@0 {
|
|
compatible = "cavium,octeon-7890-bgx-port";
|
|
reg = <0>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
sfp-slot = <&sfp0>;
|
|
};
|
|
|
|
/* SerDes 1, may differ from PCS Lane/LMAC */
|
|
eth1: ethernet-mac@1 {
|
|
compatible = "cavium,octeon-7890-bgx-port";
|
|
reg = <1>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
sfp-slot = <&sfp1>;
|
|
};
|
|
};
|