mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-25 22:20:45 +00:00
d06e4b7e25
This converts the following to Kconfig: CONFIG_VID CONFIG_VOL_MONITOR_INA220 CONFIG_VOL_MONITOR_IR36021_READ CONFIG_VOL_MONITOR_IR36021_SET CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET To finish this migration, we first need to introduce CONFIG_SPL_VID as some platforms only use this code in full U-Boot while others use it in SPL as well. To make the Kconfig logic clearer, guard all of the sub-options with a if VID || SPL_VID check. Finally, add Kconfig options for the remaining related options that did not previously have one. Signed-off-by: Tom Rini <trini@konsulko.com>
96 lines
2.2 KiB
Text
96 lines
2.2 KiB
Text
CONFIG_ARM=y
|
|
CONFIG_GIC_V3_ITS=y
|
|
CONFIG_TARGET_LS2080ARDB=y
|
|
CONFIG_TFABOOT=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x202000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x6000
|
|
CONFIG_NR_DRAM_BANKS=3
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_NXP_ESBC=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2088a-rdb-qspi"
|
|
CONFIG_FSL_USE_PCA9547_MUX=y
|
|
CONFIG_VID=y
|
|
CONFIG_VID_FLS_ENV="ls2080ardb_vdd_mv"
|
|
CONFIG_VOL_MONITOR_IR36021_READ=y
|
|
CONFIG_VOL_MONITOR_IR36021_SET=y
|
|
CONFIG_QSPI_AHB_INIT=y
|
|
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
|
|
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
|
|
CONFIG_AHCI=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_BOOTDELAY=10
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS1,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_CMD_IMLS=y
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_CMD_EEPROM=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_DM=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_MP=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_DDR_CLK_FREQ=133333333
|
|
CONFIG_DDR_ECC=y
|
|
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
|
|
CONFIG_MPC8XXX_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_I2C_MUX=y
|
|
CONFIG_I2C_MUX_PCA954x=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x57
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_NOR_FLASH=y
|
|
CONFIG_FLASH_CFI_DRIVER=y
|
|
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
|
CONFIG_SYS_FLASH_CFI=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_FSL_IFC=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
# CONFIG_SPI_FLASH_BAR is not set
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_AQUANTIA=y
|
|
CONFIG_PHY_CORTINA=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_DM_MDIO=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_FSL_LS_MDIO=y
|
|
CONFIG_NVME=y
|
|
CONFIG_PCI=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_DM_RTC=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_CONS_INDEX=2
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_DSPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_RSA=y
|
|
CONFIG_SPL_RSA=y
|
|
CONFIG_RSA_SOFTWARE_EXP=y
|
|
CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
|