mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-09-30 19:32:16 +00:00
d024236e5a
We have a large number of places where while we historically referenced gd in the code we no longer do, as well as cases where the code added that line "just in case" during development and never dropped it. Signed-off-by: Tom Rini <trini@konsulko.com>
183 lines
4.8 KiB
C
183 lines
4.8 KiB
C
/*
|
|
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
|
|
*
|
|
* Based on: gw_ventana_spl.c which is:
|
|
* Copyright (C) 2014 Gateworks Corporation
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/mx6-ddr.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <spl.h>
|
|
|
|
#include "platinum.h"
|
|
|
|
#undef RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
|
|
|
|
/* Configure MX6Q/DUAL mmdc DDR io registers */
|
|
struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
|
|
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
|
|
.dram_sdclk_0 = 0x00020030,
|
|
.dram_sdclk_1 = 0x00020030,
|
|
.dram_cas = 0x00020030,
|
|
.dram_ras = 0x00020030,
|
|
.dram_reset = 0x00020030,
|
|
/* SDCKE[0:1]: 100k pull-up */
|
|
.dram_sdcke0 = 0x00003000,
|
|
.dram_sdcke1 = 0x00003000,
|
|
/* SDBA2: pull-up disabled */
|
|
.dram_sdba2 = 0x00000000,
|
|
/* SDODT[0:1]: 100k pull-up, 40 ohm */
|
|
.dram_sdodt0 = 0x00003030,
|
|
.dram_sdodt1 = 0x00003030,
|
|
/* SDQS[0:7]: Differential input, 40 ohm */
|
|
.dram_sdqs0 = 0x00000030,
|
|
.dram_sdqs1 = 0x00000030,
|
|
.dram_sdqs2 = 0x00000030,
|
|
.dram_sdqs3 = 0x00000030,
|
|
.dram_sdqs4 = 0x00000030,
|
|
.dram_sdqs5 = 0x00000030,
|
|
.dram_sdqs6 = 0x00000030,
|
|
.dram_sdqs7 = 0x00000030,
|
|
/* DQM[0:7]: Differential input, 40 ohm */
|
|
.dram_dqm0 = 0x00020030,
|
|
.dram_dqm1 = 0x00020030,
|
|
.dram_dqm2 = 0x00020030,
|
|
.dram_dqm3 = 0x00020030,
|
|
.dram_dqm4 = 0x00020030,
|
|
.dram_dqm5 = 0x00020030,
|
|
.dram_dqm6 = 0x00020030,
|
|
.dram_dqm7 = 0x00020030,
|
|
};
|
|
|
|
/* Configure MX6Q/DUAL mmdc GRP io registers */
|
|
struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
|
|
/* DDR3 */
|
|
.grp_ddr_type = 0x000c0000,
|
|
.grp_ddrmode_ctl = 0x00020000,
|
|
/* disable DDR pullups */
|
|
.grp_ddrpke = 0x00000000,
|
|
/* ADDR[00:16], SDBA[0:1]: 40 ohm */
|
|
.grp_addds = 0x00000030,
|
|
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
|
|
.grp_ctlds = 0x00000030,
|
|
/* DATA[00:63]: Differential input, 40 ohm */
|
|
.grp_ddrmode = 0x00020000,
|
|
.grp_b0ds = 0x00000030,
|
|
.grp_b1ds = 0x00000030,
|
|
.grp_b2ds = 0x00000030,
|
|
.grp_b3ds = 0x00000030,
|
|
.grp_b4ds = 0x00000030,
|
|
.grp_b5ds = 0x00000030,
|
|
.grp_b6ds = 0x00000030,
|
|
.grp_b7ds = 0x00000030,
|
|
};
|
|
|
|
/* MT41K256M16HA-125 */
|
|
static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
|
|
.mem_speed = 1600,
|
|
.density = 4, /* 4Gbit */
|
|
.width = 16,
|
|
.banks = 8,
|
|
.rowaddr = 15,
|
|
.coladdr = 10,
|
|
.pagesz = 2,
|
|
.trcd = 1375,
|
|
.trcmin = 4875,
|
|
.trasmin = 3500,
|
|
};
|
|
|
|
/*
|
|
* Values from running the Freescale DDR stress tool via USB
|
|
*/
|
|
static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
|
|
/* write leveling calibration determine */
|
|
.p0_mpwldectrl0 = 0x0044004E,
|
|
.p0_mpwldectrl1 = 0x001F0023,
|
|
/* Read DQS Gating calibration */
|
|
.p0_mpdgctrl0 = 0x02480248,
|
|
.p0_mpdgctrl1 = 0x0210021C,
|
|
/* Read Calibration: DQS delay relative to DQ read access */
|
|
.p0_mprddlctl = 0x42444444,
|
|
/* Write Calibration: DQ/DM delay relative to DQS write access */
|
|
.p0_mpwrdlctl = 0x36322C32,
|
|
};
|
|
|
|
static void spl_dram_init(int width)
|
|
{
|
|
struct mx6_ddr3_cfg *mem = &mt41k256m16ha_125;
|
|
struct mx6_ddr_sysinfo sysinfo = {
|
|
/* width of data bus:0=16,1=32,2=64 */
|
|
.dsize = width / 32,
|
|
/* config for full 4GB range so that get_mem_size() works */
|
|
.cs_density = 32, /* 32Gb per CS */
|
|
/* single chip select */
|
|
.ncs = 1,
|
|
.cs1_mirror = 1,
|
|
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
|
|
#ifdef RTT_NOM_120OHM
|
|
.rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
|
|
#else
|
|
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
|
|
#endif
|
|
.walat = 0, /* Write additional latency */
|
|
.ralat = 5, /* Read additional latency */
|
|
.mif3_mode = 3, /* Command prediction working mode */
|
|
.bi_on = 1, /* Bank interleaving enabled */
|
|
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
|
|
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
|
|
.ddr_type = DDR_TYPE_DDR3,
|
|
.refsel = 1, /* Refresh cycles at 32KHz */
|
|
.refr = 7, /* 8 refresh commands per refresh cycle */
|
|
};
|
|
|
|
mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
|
|
mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
|
|
}
|
|
|
|
/*
|
|
* Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
|
|
* - we have a stack and a place to store GD, both in SRAM
|
|
* - no variable global data is available
|
|
*/
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
/* Setup AIPS and disable watchdog */
|
|
arch_cpu_init();
|
|
|
|
ccgr_init();
|
|
gpr_init();
|
|
|
|
/* UART iomux */
|
|
board_early_init_f();
|
|
|
|
/* Setup GP timer */
|
|
timer_init();
|
|
|
|
/* UART clocks enabled and gd valid - init serial console */
|
|
preloader_console_init();
|
|
|
|
/* Init DDR with 32bit width */
|
|
spl_dram_init(32);
|
|
|
|
/* Clear the BSS */
|
|
memset(__bss_start, 0, __bss_end - __bss_start);
|
|
|
|
/*
|
|
* Setup enet related MUXing early to give the PHY
|
|
* some time to wake-up from reset
|
|
*/
|
|
platinum_setup_enet();
|
|
|
|
/* load/boot image from boot device */
|
|
board_init_r(NULL, 0);
|
|
}
|