mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
d754254f20
This port adds support for: 1) Serial 2) eMMC 3) USB It has been tested with ARM TRUSTED FIRMWARE running u-boot as the BL33 executable [see board's README] eMMC has been tested for reading and booting the loader and linux kernels as well as saving the u-boot environment. USB has been tested with ASIX networking adapter and SanDisk 7.4GB drive. PSCI has been tested via the reset call (PSCI executes from DDR) The firwmare upgrade process has been tested via TFTP and USB FAT filesystem containing the fastboot.bin image in one of the partitions. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
288 lines
9.2 KiB
Text
288 lines
9.2 KiB
Text
================================================================================
|
||
Board Information
|
||
================================================================================
|
||
|
||
Developed by HiSilicon, the board features the Hi3798C V200 with an
|
||
integrated quad-core 64-bit ARM Cortex A53 processor and high
|
||
performance Mali T720 GPU, making it capable of running any commercial
|
||
set-top solution based on Linux or Android. Its high performance
|
||
specification also supports a premium user experience with up to H.265
|
||
HEVC decoding of 4K video at 60 frames per second.
|
||
|
||
SOC Hisilicon Hi3798CV200
|
||
CPU Quad-core ARM Cortex-A53 64 bit
|
||
DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
|
||
USB Two USB 2.0 ports One USB 3.0 ports
|
||
CONSOLE USB-micro port for console support
|
||
ETHERNET 1 GBe Ethernet
|
||
PCIE One PCIe 2.0 interfaces
|
||
JTAG 8-Pin JTAG
|
||
EXPANSION INTERFACE Linaro 96Boards Low Speed Expansion slot
|
||
DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
|
||
WIFI 802.11AC 2*2 with Bluetooth
|
||
CONNECTORS One connector for Smart Card One connector for TSI
|
||
|
||
|
||
================================================================================
|
||
BUILD INSTRUCTIONS
|
||
================================================================================
|
||
|
||
Note of warning:
|
||
================
|
||
|
||
U-boot has a *strong* dependency with the l-loader and the arm trusted firmware
|
||
repositories.
|
||
|
||
The boot sequence is:
|
||
l-loader --> arm_trusted_firmware --> u-boot
|
||
|
||
U-Boot needs to be aware of the BL31 runtime location and size to avoid writing
|
||
over it. Currently, BL31 is being placed below the kernel text offset (check
|
||
poplar.c) but this could change in the future.
|
||
|
||
The current version of u-boot has been tested with:
|
||
- https://github.com/Linaro/poplar-l-loader.git
|
||
|
||
commit f0988698dcc5c08bd0a8f50aa0457e138a5f438c
|
||
Author: Alex Elder <elder@linaro.org>
|
||
Date: Fri Jun 16 08:57:59 2017 -0500
|
||
|
||
l-loader: use external memory region definitions
|
||
|
||
The ARM Trusted Firmware code now has a header file that collects
|
||
all the definitions for the memory regions used for its boot stages.
|
||
Include that file where needed, and use the definitions found therein
|
||
|
||
Signed-off-by: Alex Elder <elder@linaro.org>
|
||
|
||
|
||
- https://github.com/Linaro/poplar-arm-trusted-firmware.git
|
||
|
||
commit 6ac42dd3be13c99aa8ce29a15073e2f19d935f68
|
||
Author: Alex Elder <elder@linaro.org>
|
||
Date: Fri Jun 16 09:24:50 2017 -0500
|
||
|
||
poplar: define memory regions in a separate file
|
||
|
||
Separate the definitions for memory regions used for the BL stage
|
||
images and FIP into a new file. The "l-loader" image uses knowledge
|
||
of the sizes and locations of these memory regions, and it can now
|
||
include this (external) header to get these definitions, rather than
|
||
having to make coordinated changes to both code bases.
|
||
|
||
The new file has a complete set of definitions (more than may be
|
||
required by one or the other user). It also includes a summary of
|
||
how the boot process works, and how it uses these regions.
|
||
|
||
It should now be relatively easy to adjust the sizes and locations
|
||
of these memory regions, or to add to them (e.g. for TEE).
|
||
|
||
Signed-off-by: Alex Elder <elder@linaro.org>
|
||
|
||
|
||
Compile from source:
|
||
====================
|
||
|
||
Get all the sources
|
||
|
||
> mkdir -p ~/poplar/src ~/poplar/bin
|
||
> cd ~/poplar/src
|
||
> git clone https://github.com/Linaro/poplar-l-loader.git l-loader
|
||
> git clone https://github.com/Linaro/poplar-arm-trusted-firmware.git atf
|
||
> git clone https://github.com/Linaro/poplar-u-boot.git u-boot
|
||
|
||
Make sure you are using the correct branch on each one of these repositories.
|
||
The definition of "correct" might change over time (at this moment in time this
|
||
would be the "latest" branch).
|
||
|
||
Compile U-Boot:
|
||
===============
|
||
|
||
Prerequisite:
|
||
# sudo apt-get install device-tree-compiler
|
||
|
||
> cd ~/poplar/src/u-boot
|
||
> make CROSS_COMPILE=aarch64-linux-gnu- poplar_defconfig
|
||
> make CROSS_COMPILE=aarch64-linux-gnu-
|
||
> cp u-boot.bin ~/poplar/bin
|
||
|
||
Compile ARM Trusted Firmware (ATF):
|
||
===================================
|
||
|
||
> cd ~/poplar/src/atf
|
||
> make CROSS_COMPILE=aarch64-linux-gnu- all fip \
|
||
SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar
|
||
|
||
Copy resulting binaries
|
||
> cp build/hi3798cv200/debug/bl1.bin ~/poplar/src/l-loader/atf/
|
||
> cp build/hi3798cv200/debug/fip.bin ~/poplar/src/l-loader/atf/
|
||
|
||
Compile l-loader:
|
||
=================
|
||
|
||
> cd ~/poplar/src/l-loader
|
||
> make clean
|
||
> make CROSS_COMPILE=arm-linux-gnueabi-
|
||
|
||
Due to BootROM requiremets, rename l-loader.bin to fastboot.bin:
|
||
> cp l-loader.bin ~/poplar/bin/fastboot.bin
|
||
|
||
|
||
================================================================================
|
||
FLASH INSTRUCTIONS
|
||
================================================================================
|
||
|
||
Two methods:
|
||
|
||
Using USB debrick support:
|
||
Copy fastboot.bin to a FAT partition on the USB drive and reboot the
|
||
poplar board while pressing S3(usb_boot).
|
||
|
||
The system will execute the new u-boot and boot into a shell which you
|
||
can then use to write to eMMC.
|
||
|
||
Using U-BOOT from shell:
|
||
1) using AXIS usb ethernet dongle and tftp
|
||
2) using FAT formated USB drive
|
||
|
||
|
||
1. TFTP (USB ethernet dongle)
|
||
=============================
|
||
|
||
Plug a USB AXIS ethernet dongle on any of the USB2 ports on the Poplar board.
|
||
Copy fastboot.bin to your tftp server.
|
||
In u-boot make sure your network is properly setup.
|
||
|
||
Then
|
||
|
||
=> tftp 0x30000000 fastboot.bin
|
||
starting USB...
|
||
USB0: USB EHCI 1.00
|
||
scanning bus 0 for devices... 1 USB Device(s) found
|
||
USB1: USB EHCI 1.00
|
||
scanning bus 1 for devices... 3 USB Device(s) found
|
||
scanning usb for storage devices... 0 Storage Device(s) found
|
||
scanning usb for ethernet devices... 1 Ethernet Device(s) found
|
||
Waiting for Ethernet connection... done.
|
||
Using asx0 device
|
||
TFTP from server 192.168.1.4; our IP address is 192.168.1.10
|
||
Filename 'poplar/fastboot.bin'.
|
||
Load address: 0x30000000
|
||
Loading: #################################################################
|
||
#################################################################
|
||
###############################################################
|
||
2 MiB/s
|
||
done
|
||
Bytes transferred = 983040 (f0000 hex)
|
||
|
||
=> mmc write 0x30000000 0 0x780
|
||
|
||
MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
|
||
=> reset
|
||
|
||
|
||
2. USING USB FAT DRIVE
|
||
=======================
|
||
|
||
Copy fastboot.bin to any partition on a FAT32 formated usb flash drive.
|
||
Enter the uboot prompt
|
||
|
||
=> fatls usb 0:2
|
||
983040 fastboot.bin
|
||
|
||
1 file(s), 0 dir(s)
|
||
|
||
=> fatload usb 0:2 0x30000000 fastboot.bin
|
||
reading fastboot.bin
|
||
983040 bytes read in 44 ms (21.3 MiB/s)
|
||
|
||
=> mmc write 0x30000000 0 0x780
|
||
|
||
MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
|
||
|
||
|
||
================================================================================
|
||
BOOT TRACE
|
||
================================================================================
|
||
|
||
Bootrom start
|
||
Boot Media: eMMC
|
||
Decrypt auxiliary code ...OK
|
||
|
||
lsadc voltage min: 000000FE, max: 000000FF, aver: 000000FE, index: 00000000
|
||
|
||
Entry boot auxiliary code
|
||
|
||
Auxiliary code - v1.00
|
||
DDR code - V1.1.2 20160205
|
||
Build: Mar 24 2016 - 17:09:44
|
||
Reg Version: v134
|
||
Reg Time: 2016/03/18 09:44:55
|
||
Reg Name: hi3798cv2dmb_hi3798cv200_ddr3_2gbyte_8bitx4_4layers.reg
|
||
|
||
Boot auxiliary code success
|
||
Bootrom success
|
||
|
||
LOADER: Switched to aarch64 mode
|
||
LOADER: Entering ARM TRUSTED FIRMWARE
|
||
LOADER: CPU0 executes at 0x000ce000
|
||
|
||
INFO: BL1: 0xe1000 - 0xe7000 [size = 24576]
|
||
NOTICE: Booting Trusted Firmware
|
||
NOTICE: BL1: v1.3(debug):v1.3-372-g1ba9c60
|
||
NOTICE: BL1: Built : 17:51:33, Apr 30 2017
|
||
INFO: BL1: RAM 0xe1000 - 0xe7000
|
||
INFO: BL1: Loading BL2
|
||
INFO: Loading image id=1 at address 0xe9000
|
||
INFO: Image id=1 loaded at address 0xe9000, size = 0x5008
|
||
NOTICE: BL1: Booting BL2
|
||
INFO: Entry point address = 0xe9000
|
||
INFO: SPSR = 0x3c5
|
||
NOTICE: BL2: v1.3(debug):v1.3-372-g1ba9c60
|
||
NOTICE: BL2: Built : 17:51:33, Apr 30 2017
|
||
INFO: BL2: Loading BL31
|
||
INFO: Loading image id=3 at address 0x129000
|
||
INFO: Image id=3 loaded at address 0x129000, size = 0x8038
|
||
INFO: BL2: Loading BL33
|
||
INFO: Loading image id=5 at address 0x37000000
|
||
INFO: Image id=5 loaded at address 0x37000000, size = 0x58f17
|
||
NOTICE: BL1: Booting BL31
|
||
INFO: Entry point address = 0x129000
|
||
INFO: SPSR = 0x3cd
|
||
INFO: Boot bl33 from 0x37000000 for 364311 Bytes
|
||
NOTICE: BL31: v1.3(debug):v1.3-372-g1ba9c60
|
||
NOTICE: BL31: Built : 17:51:33, Apr 30 2017
|
||
INFO: BL31: Initializing runtime services
|
||
INFO: BL31: Preparing for EL3 exit to normal world
|
||
INFO: Entry point address = 0x37000000
|
||
INFO: SPSR = 0x3c9
|
||
|
||
|
||
U-Boot 2017.05-rc2-00130-gd2255b0 (Apr 30 2017 - 17:51:28 +0200)poplar
|
||
|
||
Model: HiSilicon Poplar Development Board
|
||
BOARD: Hisilicon HI3798cv200 Poplar
|
||
DRAM: 1 GiB
|
||
MMC: Hisilicon DWMMC: 0
|
||
In: serial@f8b00000
|
||
Out: serial@f8b00000
|
||
Err: serial@f8b00000
|
||
Net: Net Initialization Skipped
|
||
No ethernet found.
|
||
|
||
Hit any key to stop autoboot: 0
|
||
starting USB...
|
||
USB0: USB EHCI 1.00
|
||
scanning bus 0 for devices... 1 USB Device(s) found
|
||
USB1: USB EHCI 1.00
|
||
scanning bus 1 for devices... 4 USB Device(s) found
|
||
scanning usb for storage devices... 1 Storage Device(s) found
|
||
scanning usb for ethernet devices... 1 Ethernet Device(s) found
|
||
|
||
USB device 0:
|
||
Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade
|
||
Type: Removable Hard Disk
|
||
Capacity: 7632.0 MB = 7.4 GB (15630336 x 512)
|
||
... is now current device
|
||
Scanning usb 0:1...
|
||
=>
|