mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 04:23:46 +00:00
73eca21128
This config is valid for two devices: - Odroid X2, - Odroid U3. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
143 lines
5.3 KiB
Text
143 lines
5.3 KiB
Text
U-boot for Odroid X2/U3
|
|
========================
|
|
|
|
1. Summary
|
|
==========
|
|
This is a quick instruction for setup Odroid boards based on Exynos4412.
|
|
Board config: odroid_config
|
|
|
|
2. Supported devices
|
|
====================
|
|
This U-BOOT config can be used on two boards:
|
|
- Odroid U3
|
|
- Odroid X2
|
|
with CPU Exynos 4412 rev 2.0 and 2GB of RAM
|
|
|
|
3. Boot sequence
|
|
================
|
|
iROM->BL1->(BL2 + TrustZone)->U-BOOT
|
|
|
|
This version of U-BOOT doesn't implement SPL but it is required(BL2)
|
|
and can be found in "boot.tar.gz" from here:
|
|
http://dev.odroid.com/projects/4412boot/wiki/FrontPage?action=download&value=boot.tar.gz
|
|
or here:
|
|
http://odroid.in/guides/ubuntu-lfs/boot.tar.gz
|
|
|
|
4. Boot media layout
|
|
====================
|
|
The table below shows SD/eMMC cards layout for U-boot.
|
|
The block offset is starting from 0 and the block size is 512B.
|
|
-------------------------------------
|
|
| Binary | Block offset| part type |
|
|
| name | SD | eMMC |(eMMC only)|
|
|
-------------------------------------
|
|
| Bl1 | 1 | 0 | 1 (boot) |
|
|
| Bl2 | 31 | 30 | 1 (boot) |
|
|
| U-boot | 63 | 62 | 1 (boot) |
|
|
| Tzsw | 2111 | 2110 | 1 (boot) |
|
|
| Uboot Env | 2500 | 2500 | 0 (user) |
|
|
-------------------------------------
|
|
|
|
5. Prepare the SD boot card - with SD card reader
|
|
=================================================
|
|
To prepare bootable media you need boot binaries provided by hardkernel.
|
|
File "boot.tar.gz" (link in point 3.) contains:
|
|
- E4412_S.bl1.HardKernel.bin
|
|
- E4412_S.tzsw.signed.bin
|
|
- bl2.signed.bin
|
|
- sd_fusing.sh
|
|
- u-boot.bin
|
|
|
|
This is all you need to boot this board. But if you want to use your custom
|
|
u-boot then you need to change u-boot.bin with your own u-boot binary*
|
|
and run the script "sd_fusing.sh" - this script is valid only for SD card.
|
|
|
|
*note:
|
|
The proper binary file of current U-boot is u-boot-dtb.bin.
|
|
|
|
quick steps for Linux:
|
|
- extract boot.tar.gz
|
|
- put any SD card into the SD reader
|
|
- check the device with "dmesg"
|
|
- run ./sd_fusing.sh /dev/sdX - where X is SD card device (but not a partition)
|
|
Check if Hardkernel U-boot is booting, and next do the same with your U-boot.
|
|
|
|
6. Prepare the eMMC boot card
|
|
with a eMMC card reader (boot from eMMC card slot)
|
|
=====================================================
|
|
To boot the device from the eMMC slot you should use a special card reader
|
|
which supports eMMC partiion switch. All of the boot binaries are stored
|
|
on the eMMC boot partition which is normally hidden.
|
|
|
|
The "sd_fusing.sh" script can be used after updating offsets of binaries
|
|
according to the table from point 4. Be sure that you are working on the right
|
|
eMMC partition - its size is usually very small, about 1-4 MiB.
|
|
|
|
7. Prepare the eMMC boot card
|
|
with a SD card reader (boot from SD card slot)
|
|
=================================================
|
|
If you have an eMMC->microSD adapter you can prepare the card as in point 5.
|
|
But then the device can boot only from the SD card slot.
|
|
|
|
8. Prepare the boot media using Hardkernel U-boot
|
|
=================================================
|
|
You can update the U-boot to the custom one if you have an working bootloader
|
|
delivered with the board on a eMMC/SD card. Then follow the steps:
|
|
- install the android fastboot tool
|
|
- connect a micro usb cable to the board
|
|
- on the U-boot prompt, run command: fastboot (as a root)
|
|
- on the host, run command: "fastboot flash bootloader u-boot-dtb.bin"
|
|
- the custom U-boot should start after the board resets.
|
|
|
|
9. Partition layout
|
|
====================
|
|
Default U-boot environment is setup for fixed partiion layout.
|
|
|
|
Partition table: MSDOS. Disk layout and files as listed in the table below.
|
|
----- ------ ------ ------ -------- ---------------------------------
|
|
| Num | Name | FS | Size | Offset | Reguired files |
|
|
| | | Type | MiB | MiB | |
|
|
----- ------ ------ ------ -------- ---------------------------------
|
|
| 1 | BOOT | fat | 100 | 2 | kernel, fdt** |
|
|
| 2 | ROOT | ext4 | - | | any Linux system |
|
|
----- ------ ------ ------ -------- ---------------------------------
|
|
|
|
**note:
|
|
Supported fdt files are:
|
|
- exynos4412-odroidx2.dtb
|
|
- exynos4412-odroidu3.dtb
|
|
|
|
Supported kernel files are:
|
|
- Image.itb
|
|
- zImage
|
|
- uImage
|
|
|
|
The default environmental variable "dfu_alt_info" is set* for above layout.
|
|
Each partition size is just an example, dfu_alt_info tries init two partitions.
|
|
The size of each is not important.
|
|
|
|
*note:
|
|
$dfu_alt_info is set on a boot time and it is concatenated using two variables:
|
|
- $dfu_alt_boot(set dynamically)
|
|
- $dfu_alt_system(from current env).
|
|
|
|
To add any changes to dfu_alt_info - please modify $dfu_alt_system only.
|
|
Changes are visible after board reset.
|
|
|
|
10. The environment and booting the kernel
|
|
==========================================
|
|
There are three macros defined in config for various boot options:
|
|
Two for both, kernel with device tree support and also without it:
|
|
- boot_uimg - load uImage
|
|
- boot_zimg - load zImage
|
|
If proper fdt file exists then it will be automatically loaded,
|
|
so for old kernel types, please remove fdt file from boot partition.
|
|
|
|
The third boot option for multi image support (more info: doc/uImage.FIT/)
|
|
- boot_fit - for binary file: "Image.itb"
|
|
|
|
Default boot command: "autoboot"
|
|
And the boot sequence is:
|
|
- boot_fit - if "Image.itb" exists
|
|
- boot_zimg - if "zImage" exists
|
|
- boot_uimg - if "uImage" exists
|