mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 12:33:41 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
147 lines
4.5 KiB
C
147 lines
4.5 KiB
C
/*
|
|
* Copyright (c) 2004 Picture Elements, Inc.
|
|
* Stephen Williams (steve@icarus.com)
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
# include <common.h>
|
|
# include <asm/ppc4xx.h>
|
|
# include <asm/processor.h>
|
|
# include <asm/io.h>
|
|
# include "jse_priv.h"
|
|
|
|
/*
|
|
* This function is run very early, out of flash, and before devices are
|
|
* initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue
|
|
* of being in the init_sequence array.
|
|
*
|
|
* The SDRAM has been initialized already -- start.S:start called
|
|
* init.S:init_sdram early on -- but it is not yet being used for
|
|
* anything, not even stack. So be careful.
|
|
*/
|
|
int board_early_init_f (void)
|
|
{
|
|
/*-------------------------------------------------------------------------+
|
|
| Interrupt controller setup for the JSE board.
|
|
| Note: IRQ 0-15 405GP internally generated; active high; level sensitive
|
|
| IRQ 16 405GP internally generated; active low; level sensitive
|
|
| IRQ 17-24 RESERVED/UNUSED
|
|
| IRQ 25 (EXT IRQ 0) PCI SLOT 0; active low; level sensitive
|
|
| IRQ 26 (EXT IRQ 1) PCI SLOT 1; active low; level sensitive
|
|
| IRQ 27 (EXT IRQ 2) JP2C CHIP ; active low; level sensitive
|
|
| IRQ 28 (EXT IRQ 3) PCI bridge; active low; level sensitive
|
|
| IRQ 29 (EXT IRQ 4) SystemACE IRQ; active high
|
|
| IRQ 30 (EXT IRQ 5) SystemACE BRdy (unused)
|
|
| IRQ 31 (EXT IRQ 6) (unused)
|
|
+-------------------------------------------------------------------------*/
|
|
mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
mtdcr (UIC0ER, 0x00000000); /* disable all ints */
|
|
mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */
|
|
mtdcr (UIC0PR, 0xFFFFFF87); /* set int polarities */
|
|
mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
|
|
mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
|
|
/* Configure the interface to the SystemACE MCU port.
|
|
The SystemACE is fast, but there is no reason to have
|
|
excessivly tight timings. So the settings are slightly
|
|
generous. */
|
|
|
|
/* EBC0_B1AP: BME=1, TWT=2, CSN=0, OEN=1,
|
|
WBN=0, WBF=1, TH=0, RE=0, SOR=0, BEM=0, PEN=0 */
|
|
mtdcr (EBC0_CFGADDR, PB1AP);
|
|
mtdcr (EBC0_CFGDATA, 0x01011000);
|
|
|
|
/* EBC0_B1CR: BAS=x, BS=0(1MB), BU=3(R/W), BW=0(8bits) */
|
|
mtdcr (EBC0_CFGADDR, PB1CR);
|
|
mtdcr (EBC0_CFGDATA, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
|
|
|
|
/* Enable the /PerWE output as /PerWE, instead of /PCIINT. */
|
|
/* CPC0_CR1 |= PCIPW */
|
|
mtdcr (0xb2, mfdcr (0xb2) | 0x00004000);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_BOARD_PRE_INIT
|
|
int board_pre_init (void)
|
|
{
|
|
return board_early_init_f ();
|
|
}
|
|
|
|
#endif
|
|
|
|
/*
|
|
* This function is also called by arch/powerpc/lib/board.c:board_init_f (it is
|
|
* also in the init_sequence array) but later. Many more things are
|
|
* configured, but we are still running from flash.
|
|
*/
|
|
int checkboard (void)
|
|
{
|
|
unsigned vers, status;
|
|
|
|
/* check that the SystemACE chip is alive. */
|
|
printf ("ACE: ");
|
|
vers = readw (CONFIG_SYS_SYSTEMACE_BASE + 0x16);
|
|
printf ("SystemACE %u.%u (build %u)",
|
|
(vers >> 12) & 0x0f, (vers >> 8) & 0x0f, vers & 0xff);
|
|
|
|
status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
|
|
#ifdef DEBUG
|
|
printf (" STATUS=0x%08x", status);
|
|
#endif
|
|
/* If the flash card is present and there is an initial error,
|
|
then force a restart of the program. */
|
|
if (status & 0x00000010) {
|
|
printf (" CFDETECT");
|
|
|
|
if (status & 0x04) {
|
|
/* CONTROLREG = CFGPROG */
|
|
writew (0x1000, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
|
|
udelay (500);
|
|
/* CONTROLREG = CFGRESET */
|
|
writew (0x0080, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
|
|
udelay (500);
|
|
writew (0x0000, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
|
|
/* CONTROLREG = CFGSTART */
|
|
writew (0x0020, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
|
|
|
|
status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
|
|
}
|
|
}
|
|
|
|
/* Wait for the SystemACE to program its chain of devices. */
|
|
while ((status & 0x84) == 0x00) {
|
|
udelay (500);
|
|
status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
|
|
}
|
|
|
|
if (status & 0x04)
|
|
printf (" CFG-ERROR");
|
|
if (status & 0x80)
|
|
printf (" CFGDONE");
|
|
|
|
printf ("\n");
|
|
|
|
/* Force /RTS to active. The board it not wired quite
|
|
correctly to use cts/rtc flow control, so just force the
|
|
/RST active and forget about it. */
|
|
writeb (readb (0xef600404) | 0x03, 0xef600404);
|
|
|
|
printf ("JSE: ready\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* **** No more functions called by board_init_f. **** */
|
|
|
|
/*
|
|
* This function is called by arch/powerpc/lib/board.c:board_init_r. At this
|
|
* point, basic setup is done, U-Boot has been moved into SDRAM and
|
|
* PCI has been set up. From here we done late setup.
|
|
*/
|
|
int misc_init_r (void)
|
|
{
|
|
host_bridge_init ();
|
|
return 0;
|
|
}
|